Skip to the content
2 layers40 × 30 mmThreadnode h2, the printed circuit board in 3D

Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

Size
40 × 30 mm
Copper layers
2
Thickness
1.6 mm
Parts
18
Nets
11
Pads
90
Tracks, vias
52, 30
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
11 Aug 2026
Updated
25 Sep 2026

Overview

Threadnode h2 is an open-source printed circuit board by AskAlice, from the AskAlice/home-automation-pcbs repository on GitHub, published under the MIT licence. It is a 2-layer board of 40 × 30 mm with 18 parts on 11 nets, routed with 52 tracks and 30 vias.

It is built around the ESP32-H2-MINI-1U. Its parts include 5 resistors, 3 capacitors, 2 connectors, 1 IC and 1 diode. It belongs with the ESP32 and RISC-V boards of this library.

Main components

1

README

boards/threadnode-h2/README.md

threadnode-h2 — battery Thread contact/button node (SPEC 7.1)

ESP32-H2-MINI-1 node on CR2032 with reed-switch input, user button, I2C expansion header, and programming header. v0.1 concept board.

  • Board: 40 × 30 mm, 2-layer, 3 mounting holes
  • Power: CR2032 (BT1) direct to +3V3 (no LDO) — brown-out risk below ~2.6 V
  • Status: python3 boards/wave2/wave2gen.py threadnode-h2 → self-check OK

BOM (bom_lcsc.csv)

RefValueFootprintLCSC #MPNQty
U1ESP32-H2-MINI-1ESP32-H2-MINI-1C2924539ESP32-H2-MINI-1-N41
BT1CR2032custom:CR2032-SMDC70377MY-BS-03-A1AJ1
SW1Reed switchcustom:Reed-MK24C140342MK24-B-21
D1LED green0603C7204319-217/GHC-YR1S2/3T1
R81k0603C211900603WAF1001T5E1
R4,R54.7k0603C231620603WAF4701T5E2
R1,R2,R3,R710k0603C982520603WAF1002T5E4
C1,C2,C3100nF0603C14663CL10B104KB8NNNC3
BT2SW_PUSHcustom:Tactile-6x6-SMDC91808TS-1187A-B-A-B1
J1Conn_01x04 (3V3/TX0/RX0/GND)PinHeader_1x04_P2.54mmC49241A2541WV-4P1
J2Conn_01x04 (3V3/SDA/SCL/GND)PinHeader_1x04_P2.54mmC49241A2541WV-4P1

Pinout (H2-MINI-1)

SignalGPIONotes
REEDGPIO3reed switch to GND, deep-sleep wakeup
I2C_SDA / I2C_SCLGPIO12 / GPIO13J2 header, 4.7k pull-ups R4/R5
STAT_LEDGPIO8green LED via R8 (pulse only — battery)
BTN (BOOT)GPIO9user button; hold at reset = ROM bootloader
TX0 / RX0GPIO24 / GPIO23J1 prog header (flash + log; no USB)
EN—R1 10k pull-up + C3 100nF

Firmware

See esphome/threadnode-h2.yaml. H2 has no Wi-Fi — production firmware targets Matter-over-Thread (esp-matter) or Zigbee; yaml validates the I/O map with logger + deep-sleep on GPIO3.

Routing status

v0.1 concept — signals left for autorouting. Power rails (+3V3/GND/EN) routed with B.Cu trunk + F.Cu drops and GND via-stitching; all signal nets (I2C, UART, reed, LED) are unrouted ratsnest.

Analyzer notes

analyze_pcb.py: DFM-001 = 0. Expect RT-001 unrouted-net errors (by design, signals left for autorouting) and PM courtyard notes around the CR2032 holder / tactile button GND pads touching GND mounting-hole copper (electrically joined by design).

Caveats (verify before fabrication!)

  • CR2032 voltage (2.8–3.6 V) grazes the H2 brown-out threshold; short LED pulses only. Verify with esp-idf brownout settings.
  • I2C pads (J2) are on strapping-adjacent GPIOs — double-check the H2 datasheet (GPIO8/9/25/26/27 strapping) before reusing.
  • No USB connector: flash via J1 (3V3/TX0/RX0/GND) or add USB-JTAG wiring.
  • Verify all footprints, pin numbers, and clearances against KiCad libraries + datasheets before ordering boards.

Renders

Raytraced 3D (KiCad)2D layout
toptop
bottombottom

360° turntable

🎬 24 real KiCad raytraced frames stitched with ffmpeg (tools/turntable.sh).

Parts

18
QtyValueFootprintReferences
3MountingHole_M2.5threadnode-h2:MountingHole_M2.5H1, H2, H3
2100nFCapacitor_SMD:C_0603_1608MetricC2, C3
24.7kResistor_SMD:R_0603_1608MetricR4, R5
2Conn_01x04Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ1, J2
1100kResistor_SMD:R_0603_1608MetricR3
110kResistor_SMD:R_0603_1608MetricR2
110uFCapacitor_SMD:C_0603_1608MetricC1
11kResistor_SMD:R_0603_1608MetricR1
1CR2032_HOLDERthreadnode-h2:CR2032-holderBT1
1ESP32-H2-MINI-1threadnode-h2:ESP32-H2-MINI-1U1
1LED_GRNLED_SMD:LED_0603_1608MetricD1
1REEDthreadnode-h2:Reed-SMDSW1
1SW_PUSHthreadnode-h2:Tactile-6x6-SMDBT2

More from AskAlice/home-automation-pcbs

11
  • 2 layers80 × 50 mmLedhub c6, the printed circuit board in 3D

    Ledhub c6

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    59 parts1MIT
  • 2 layers50 × 40 mmLedquad c3, the printed circuit board in 3D

    Ledquad c3

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    52 parts1MIT
  • 2 layers60 × 40 mmRelaymini c3, the printed circuit board in 3D

    Relaymini c3

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    39 parts1MIT
  • 2 layers100 × 60 mmGaragepilot c6, the printed circuit board in 3D

    Garagepilot c6

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    35 parts1MIT
  • 2 layers60 × 40 mmSensenode c6, the printed circuit board in 3D

    Sensenode c6

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    35 parts1MIT
  • 2 layers45 × 35 mmPresencepro c3, the printed circuit board in 3D

    Presencepro c3

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    33 parts1MIT
  • 2 layers70 × 50 mmBlinddriver c6, the printed circuit board in 3D

    Blinddriver c6

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    32 parts1MIT
  • 2 layers40 × 30 mmIrblaster c3, the printed circuit board in 3D

    Irblaster c3

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    27 parts1MIT
  • 2 layers60 × 40 mmAirquality s3, the printed circuit board in 3D

    Airquality s3

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    25 parts1MIT
  • 2 layers70 × 25 mmGardenprobe c6, the printed circuit board in 3D

    Gardenprobe c6

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    19 parts1MIT
  • 2 layers35 × 20 mmThreadrcp h2, the printed circuit board in 3D

    Threadrcp h2

    AskAlice/home-automation-pcbs

    Daily Kimi-generated home automation PCB designs with KiCad sources, 3D models, and rendered documentation

    19 parts1MIT

Similar boards

  • 4 layers36 × 50.2 mmRacer, the printed circuit board in 3D

    Racer

    StuckAtPrototype/Racer

    These are structured into their own files. I could have used submodules, but decided against it.

    83 parts3.8kApache-2.0
  • 2 layers45 × 45 mmAirCube, the printed circuit board in 3D

    AirCube

    StuckAtPrototype/AirCube

    Works standalone out of the box. Pairs with Home Assistant in minutes. Other platforms are supported through community-contributed extensions.

    61 parts379Apache-2.0
  • 4 layers74.7 × 30 mmController, the printed circuit board in 3D

    Controller

    StuckAtPrototype/Thumbtroller

    77 parts305
  • 4 layers49 × 74.9 mmPCB business card, the printed circuit board in 3D

    PCB business card

    StuckAtPrototype/PCB_business_card_remake

    A custom PCB based "business" card that lets you play a version of Flappy Bird.

    311 parts132Apache-2.0
  • 2 layers22 × 32 mmH2 carrier, the printed circuit board in 3D

    H2 carrier

    Pulpyyyy/zigcreate-ota

    OTA firmware releases for zigcreate (ESP32-H2 Zigbee)

    3 parts16
  • 2 layersESP32-H2-MINI-1, the printed circuit board in 3D

    ESP32-H2-MINI-1

    74th/esp32-dev-boards

    ESP32 Dev Boards PCB

    46 parts8MIT
  • 4 layers50 × 22 mmMain pcb, the printed circuit board in 3D

    Main pcb

    antoine-prrn/mia-ou

    A smart, connected device designed to be attached to pet collars. It monitors various animal metrics and enables interaction via a mobile app. Built for safety, health, and user engagement.

    57 parts1
  • 4 layers62 × 67 mmMain pcb, the printed circuit board in 3D

    Main pcb

    Andreasdahlberg/zkmeter

    ZK-meter is a Zigbee HAN-module for Kamstrup Omnipower electricity meters.

    57 partsCC0-1.0

Questions

How big is the Threadnode h2 PCB?

It measures 40 × 30 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Threadnode h2 use?

18 parts, built around the ESP32-H2-MINI-1U. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Threadnode h2 KiCad files?

From the AskAlice/home-automation-pcbs repository on GitHub, at the commit this page was made from: the board is boards/threadnode-h2/threadnode-h2.kicad_pcb and its schematic boards/airquality-s3/airquality-s3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Threadnode h2 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).