Skip to the content
2 layers81 × 47 mmD34-ctrl, the printed circuit board in 3D

A high performance cat-food-feeder.

Size
81 × 47 mm
Copper layers
2
Thickness
1.6 mm
Parts
45
Nets
65
Pads
185
Tracks, vias
849, 44
Pours
6
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 Nov 2026
Updated
1 Nov 2026

Overview

D34-ctrl is an open-source printed circuit board by aquarat, from the aquarat/cat-feeder repository on GitHub. It is a 2-layer board of 81 × 47 mm with 45 parts on 65 nets, routed with 849 tracks and 44 vias.

It is built around the ESP32-DEVKITC-32E, 74HC123D and 74HC573, with the BAT42 among its other parts. Its parts include 26 resistors, 6 capacitors, 6 connectors, 4 diodes and 3 ICs. It belongs with the ESP32 boards of this library.

Main components

4

README

electronics/revb/power/README.md

Rev B power-block handoff

Selected: AP63203WU-7 / C780769 for 3.3 V (1 A design budget); AP63201WU-7 / C2071044 for approximately 12 V (0.5 A fan-start budget, 0.14 A normal).

Read rationale, layout constraints and qualification gaps.

  • circuit.json: complete 22-component numbered-pin integration contract, MPNs, JLC codes, KiCad symbols/footprints, datasheet links.
  • design.py: source generator; follows the motor block's parts schema.
  • analysis.json, analyze.py, test_power.py: explicit assumptions and eight analytical/fault-injection tests.
  • stock-evidence.json, refresh-stock.py: read-only public stock snapshots, including rejected candidates; selection is defined by circuit.json, not by presence in the evidence file.
  • kicad-audit.json, audit_kicad.py, power.pretty/: installed KiCad 9.0.2 symbol/pad checks and exact standard footprint copies.
  • reference-sources.json, retained PDFs/text: manufacturer-authored reference evidence and mirror provenance.

Required upstream contract: SYS_20V is a hardware-qualified 20 V switched supply, OFF for fallback contracts and contract loss. Both buck EN pins tie to this supply. Neither rail waits on ESP32 firmware. Feed motor power and DPS5005 separately from the qualified 20 V bus; include the buck banks' 40 µF nominal input capacitance in upstream switch inrush calculations.

The new PCB integrator must check layout/loop/transient/thermal behavior. These files contain no full-board layout and no physical test results. Capacitor DC-bias retention and 10 µs load-step recovery are screening assumptions, not measured guarantees. The 0.5 A fan-start budget is not a qualified continuous thermal rating.

Parts

45
QtyValueFootprintReferences
101kd34:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR5, R6, R8, R10, R11, R14, R16, R18, R21, R22
910kd34:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR2, R4, R7, R15, R17, R20, R23, R24, R25
347kd34:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR3, R12, R19
2100nd34:C_Rect_L4.0mm_W2.5mm_P2.50mmC6, C7
21ud34:C_Rect_L5.5mm_W3.2mm_P2.50mmC4, C5
222u 50Vd34:CP_Radial_D5.0mm_P2.00mmC1, C2
11N5817d34:D_DO-41_SOD81_P2.54mm_Vertical_AnodeUpD2
11N5817d34:D_DO-41_SOD81_P10.16mm_HorizontalD1
1330d34:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR13
14.7kd34:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR9
1470kd34:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_VerticalR26
1470kd34:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR1
174HC123d34:DIP-16_W7.62mmU2
174HC573d34:DIP-20_W7.62mmU3
1BAT42d34:D_DO-35_SOD27_P2.54mm_Vertical_AnodeUpD9
1DPS5005 UART (3.3 V TTL; DPS order GND TX RX 3V3)d34:JST_XH_B4B-XH-A_1x04_P2.50mm_VerticalJ11
1ESP32-DevKitC-32Ed34:ESP32-DevKitC-32E_SocketU1
1HOME sensor (DRV5023 hall, 3.3 V, open drain)d34:JST_XH_B3B-XH-A_1x03_P2.50mm_VerticalJ3
1LID reed + basin-full probed34:JST_XH_B4B-XH-A_1x04_P2.50mm_VerticalJ4
1LINK to D34-PWRd34:JST_XH_B11B-XH-A_1x11_P2.50mm_VerticalJ1
1LINK to D34-TECd34:JST_XH_B12B-XH-A_1x12_P2.50mm_VerticalJ2
1STATUSd34:LED_D3.0mmD3
1UI: panel LED + buttond34:JST_XH_B5B-XH-A_1x05_P2.50mm_VerticalJ6

More from aquarat/cat-feeder

5
  • 2 layers57.9 × 80 mmFeeder, the printed circuit board in 3D

    Feeder

    aquarat/cat-feeder

    A high performance cat-food-feeder.

    54 parts
  • 2 layers81 × 47 mmD34-tec unrouted, the printed circuit board in 3D

    D34-tec unrouted

    aquarat/cat-feeder

    A high performance cat-food-feeder.

    39 parts
  • 2 layers81 × 47 mmD34-pwr, the printed circuit board in 3D

    D34-pwr

    aquarat/cat-feeder

    A high performance cat-food-feeder.

    24 parts
  • 2 layers17.7 × 16.5 mmFan placement, the printed circuit board in 3D

    Fan placement

    aquarat/cat-feeder

    A high performance cat-food-feeder.

    12 parts
  • 2 layers14.3 × 17.7 mmLogic placement, the printed circuit board in 3D

    Logic placement

    aquarat/cat-feeder

    A high performance cat-food-feeder.

    10 parts

Similar boards

  • 4 layers220 × 160 mmQds cv, the printed circuit board in 3D

    Qds cv

    cnpem-emi/qds-cv-hw

    Quench detection system for a single superconducting coil working in the Vertical Cryostat.

    403 parts
  • 2 layers44 × 100 mmHP45 Standalone V4.02, the printed circuit board in 3D

    HP45 Standalone V4.02

    yvodehaas/HP45-standalone-controller-V4.02

    HP45 standalone controller V4.02

    90 parts36GPL-3.0
  • 2 layers198.1 × 193 mmSTE25, the printed circuit board in 3D

    STE25

    stonedDiscord/Automatenplatinen

    Reverse engineerte Hardware aus deutschen Spielautomaten.

    252 parts5BSD-2-Clause
  • 2 layers87.5 × 60 mmSingle step-6502, the printed circuit board in 3D

    Single step-6502

    ceharris/single-step-6502

    Single step controller module for the 6502 microprocessor

    33 parts1
  • 2 layers160 × 100 mmDCC V2, the printed circuit board in 3D

    DCC V2

    PaulVdBergh/DCC_Hardware

    The repository for DCC Hardware projects

    101 parts1

Questions

How big is the D34-ctrl PCB?

It measures 81 × 47 mm and has 2 copper layers, 1.6 mm thick.

What parts does the D34-ctrl use?

45 parts, built around the ESP32-DEVKITC-32E, 74HC123D, 74HC573 and BAT42. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the D34-ctrl KiCad files?

From the aquarat/cat-feeder repository on GitHub, at the commit this page was made from: the board is electronics/d34/d34-ctrl/d34-ctrl.kicad_pcb and its schematic electronics/d34/d34-ctrl/d34-ctrl.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the D34-ctrl design in my own project?

Its repository states no licence, so its author keeps all rights: ask aquarat before reusing the design.