

Stm8l test
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 60
- Nets
- 36
- Pads
- 160
- Tracks, vias
- 509, 77
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 11 Apr 2021
- Updated
- 6 Jan 2022
Overview
Stm8l test is an open-source printed circuit board by antonloof, from the antonloof/eggtimer repository on GitHub. It is a 2-layer board with 60 parts on 36 nets, routed with 509 tracks and 77 vias.
It is built around the STM8L101F3P6, BD70522GUL-E2 and TLMS1000-GS08, with the SI2365EDS-T1-GE3 among its other parts. Its parts include 31 diodes, 8 transistors, 4 resistors, 3 capacitors and 3 switches. It belongs with the STM8 boards of this library.
Main components
4STM8L101F3P6
TSSOP-20-40℃~+85℃ 1.65V~3.6V 16MHz 18 2KB 8 Bit 8KB Built-in FLASH STM8 TSSOP-20 Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)BD70522GUL-E2
UFBGA-9-40℃~+85℃ 1 1.2V~3.3V 180nA 1MHz 2.5V~5.5V 500mA Buck Buck Built-in No UFBGA-9 DC-DC Converters ROHSROHM SemiconductorDC-DC ConvertersTLMS1000-GS08
0603-40℃~+100℃ 1.6mm x 0.8mm square LED 1.8V 160° 2mA 40mW 4mcd 628nm 640nm AlGaInP Discrete Diode Red 0603 LED Indication - Discrete ROHSVishay IntertechnologyLED Indication - DiscreteSI2365EDS-T1-GE3
SOT-23-3-55℃~+150℃ 1 P-Channel 1.1W 13.8nC@8V 20V 32mΩ@4.5V 400mV 5.9A P-Channel SOT-23-3 MOSFETs ROHSVishay IntertechnologyMOSFETs
README
README.mdeggtimer
Parts
60| Qty | Value | Footprint | References |
|---|---|---|---|
| 30 | TLMS1000-GS08 | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24 +14 |
| 7 | SI2365EDS-T1-GE3 | Package_TO_SOT_SMD:SOT-23_Handsoldering | Q1, Q3, Q4, Q5, Q6, Q7, Q8 |
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 2 | 100k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2 |
| 2 | 22u | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C3 |
| 1 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C4 |
| 1 | 180 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R4 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3 |
| 1 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q2 |
| 1 | 2u2 | Inductor_SMD:L_Wuerth_WE-PD-Typ-7345 | L1 |
| 1 | 500ma | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | F1 |
| 1 | BD70522GUL-E2 | good_things:BGA-9_3x3_1.76x1.56mm | U1 |
| 1 | Battery_Cell | Battery:BatteryHolder_Keystone_3002_1x2032 | BT1 |
| 1 | Buzzer | good_things:buzzer_d14_p5 | BZ1 |
| 1 | Conn_01x04 | good_things:TSM-104-01-L-SH | J1 |
| 1 | D_Small | Diode_SMD:D_1210_3225Metric_Pad1.42x2.65mm_HandSolder | D1 |
| 1 | Rotary_Encoder_Switch | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW3 |
| 1 | STM8L101F3P | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | SW_Push | good_things:push_sw_purple | SW2 |
| 1 | prog_sw | good_things:TSM-103-01-l_SH | SW1 |
More from antonloof/eggtimer
1- 2 layers

Similar boards
- 2 layers68 × 35.3 mm

- 4 layers65.4 × 53.7 mm

HV POWER SUPPLY
Sooraj21s/High-Volt-Radiation-Detect-PCB
A PCB that converts the radiatoin detected by the geiger tube captured as milli volts to a high voltage by opamp & a buzzer is also provided in the module that triggers when the detected voltage reaches a certain…
83 parts - 2 layers140 × 72 mm

- 2 layers35.5 × 20 mm

- 2 layers105 × 42 mm

- 2 layers35 × 50 mm

- 2 layers32.9 × 119.1 mm

- 2 layers35.9 × 62.7 mm

Rp2040-memcard
sd2psx/pcb
The PCB must be produced in 0.8mm thickness. Production files are provided under the "Releases" tab. These do not include the through-hole OLED module.
60 parts241
Questions
What parts does the Stm8l test use?
60 parts, built around the STM8L101F3P6, BD70522GUL-E2, TLMS1000-GS08 and SI2365EDS-T1-GE3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Stm8l test KiCad files?
From the antonloof/eggtimer repository on GitHub, at the commit this page was made from: the board is stm8_based/kicad/stm8l_test.kicad_pcb and its schematic eggtimer_pcb/eggtimer_pcb.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Stm8l test design in my own project?
Its repository states no licence, so its author keeps all rights: ask antonloof before reusing the design.