Skip to the content
2 layers69 × 56.8 mmBeal TX, the printed circuit board in 3D

Kicad project for a Lora valves controller

Size
69 × 56.8 mm
Copper layers
2
Thickness
1.58 mm
Parts
93
Nets
64
Pads
317
Tracks, vias
524, 66
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
12 Aug 2026
Updated
19 Oct 2026

Overview

Beal TX is an open-source printed circuit board by anobli, from the anobli/beal-hw repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 69 × 56.8 mm with 93 parts on 64 nets, routed with 524 tracks and 66 vias.

It is built around the LORA-E5-HF, DRV8912QPWPRQ1 and LM5157QRTERQ1, with the TPSM863253RDXR, ESD9X12ST5G and CRCW040210K0FKEDC among its other parts. Its parts include 25 capacitors, 23 resistors, 12 diodes, 6 connectors and 4 ICs. It belongs with the radio and wireless boards of this library.

Main components

12

README

Beal-Rx/README.md

Beal-Rx — input board

Beal-Rx clips onto an existing irrigation controller's zone-output wiring, senses which zone it's energizing, and reports that over LoRa to one or more Beal-TX units. It is the LoRa coordinator of a Beal system — it's where commands originate, and it's already the natural central device since it's the one wired to the existing controller.

The schematic is split into three sheets: Inputs, Radio, Power.

Inputs (io_ext.kicad_sch)

  • 12 sense channels, each isolated from the field wiring by an opto-isolator (3× LTV-844S, 4 channels each). This gives galvanic isolation from whatever the existing controller puts on its zone outputs, with no current drawn from or injected back into the controller.
  • Sized against 24VAC zone outputs but tolerant of smaller signals (9VAC/9VDC), so the same board can read other controller types without a hardware change.
  • A 14-position terminal block (TBL004-508-14BE-2GY) brings in the 12 channels plus the shared INPUT_COM return.
  • A dedicated STM32C031K6Ux MCU on this sheet scans all 12 opto outputs and reports state changes up to the LoRa-E5 (I2C/UART, plus an interrupt line) — the LoRa-E5 doesn't have enough spare GPIOs to read 12 channels directly itself, so this small companion MCU owns the input-scanning job. It has its own SWD (TC2050) connector for programming/debug.

Radio (radio_mcu.kicad_sch)

  • LoRa-E5 module (U5, Seeed, STM32WL-based) — the application MCU. It owns the LoRa radio, drives the status LED (D3), reads the pairing button (SW2, on its own dedicated GPIO), and talks to the Inputs sheet's STM32C031 over I2C/UART to learn which zone just turned on.
  • Pairing button (SW2) behavior:
    • Short press: pairs this coordinator with a Beal-TX peer (implemented).
    • Double press: maps a specific input channel to a specific output channel on a specific Beal-TX (planned, procedure still TBD).
    • Long press: probable factory reset (not decided).
  • U.FL/antenna connector (J1) for the 868 MHz antenna.
  • USB-C connector (J5) — power input only.
  • SWD (Tag-Connect J7) for programming/debugging the LoRa-E5.
  • One extension connector (J2, Conn_02x04_Odd_Even) reserved for a future add-on board (e.g. more sense inputs) — not used by anything today.

Power (power.kicad_sch)

  • TPSM863253 buck power module producing the board's logic-level rail from USB 5V. No boost converter or valve driver on this board — Beal-Rx only senses, it never drives anything, so it has no need for the 9V drive rail that Beal-TX needs.
  • Powered from a 5V USB supply (mains-adapter or similar) — it lives next to the existing controller, which typically has power available nearby.

Open items

  • Channel-to-channel mapping procedure (input on Beal-Rx → output on a specific Beal-TX) — design not finalized.
  • Long-press button behavior (factory reset) — not decided.
  • Extension connector (J2) use case — reserved, nothing designed against it yet.

Parts

93
QtyValueFootprintReferences
16TestPointTestPoint:TestPoint_Pad_D1.0mmTP1, TP2, TP3, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP21, TP22
6ESD9X12ST5GDiode_SMD:D_SOD-923D2, D5, D8, D9, D10, D11
50.1uFCapacitor_SMD:C_0805_2012MetricC5, C7, C17, C18, C33
510kResistor_SMD:R_0402_1005MetricR4, R6, R10, R13, R23
4470Resistor_SMD:R_0402_1005MetricR5, R7, R8, R9
4LEDLED_SMD:LED_0603_1608MetricD3, D4, D7, D15
4MountingHoleMountingHole:MountingHole_2.1mmH1, H2, H3, H4
310uFCapacitor_SMD:C_1206_3216MetricC2, C20, C32
20Resistor_SMD:R_0402_1005MetricR17, R28
20.1uFCapacitor_SMD:C_0402_1005MetricC16, C28
210nFCapacitor_SMD:C_0402_1005MetricC3, C29
210uFCapacitor_SMD:C_0805_2012MetricC6, C19
21uFCapacitor_SMD:C_0603_1608MetricC9, C25
25.1kResistor_SMD:R_0402_1005MetricR1, R2
28.2mFCapacitor_THT:CP_Radial_D25.0mm_P10.00mm_SnapInC8, C11
2CCapacitor_SMD:C_0603_1608MetricC4, C40
2Conn_02x04_Odd_EvenConnector_PinHeader_1.00mm:PinHeader_2x04_P1.00mm_Vertical_SMDJ3, J4
10Inductor_SMD:L_0603_1608MetricL2
110KResistor_SMD:R_0402_1005MetricR14
1143kResistor_SMD:R_0402_1005MetricR11
119.1kResistor_SMD:R_0402_1005MetricR3
11kResistor_SMD:R_0402_1005MetricR15
11uHInductor_SMD:L_Wuerth_WE-PD-Typ-7345L4
12.2uFCapacitor_SMD:C_0805_2012MetricC1
12.49kResistor_SMD:R_0402_1005MetricR26
120kResistor_SMD:R_0402_1005MetricR25
122uFCapacitor_SMD:C_0805_2012MetricC27
130Resistor_SMD:R_2512_6332MetricR16
1300pFCapacitor_SMD:C_0402_1005MetricC21
14.7uFCapacitor_SMD:C_0805_2012MetricC10
14.7uFCapacitor_SMD:C_0402_1005MetricC30
166.5kResistor_SMD:R_0402_1005MetricR12
19.76kResistor_SMD:R_0402_1005MetricR24
1953Resistor_SMD:R_0402_1005MetricR27
1CONMHF1-SMD-TCONMHF1-SMD-T:CONMHF1SMDTJ1
1DRV8912QPWPRQ1Package_SO:HTSSOP-24-1EP_4.4x7.8mm_P0.65mm_EP3.4x7.8mm_Mask2.4x4.68mm_ThermalViasU6
1LM5157-Q1Package_DFN_QFN:WQFN-16-1EP_3x3mm_P0.5mm_EP1.68x1.68mm_ThermalViasU150
1LoRa-E5Lora-E5:LoRa-E5U5
1SS34-E3/57TDiode_SMD:D_SMBD6
1SW_PushButton_Switch_THT:SW_PUSH_6mmSW2
1SZESD9B5.0ST5GDiode_SMD:D_SOD-923D1
1Screw_Terminal_01x06Beal:691401710006BJ6
1TC2050Connector:Tag-Connect_TC2050-IDC-NL_2x05_P1.27mm_VerticalJ7
1TPSM863253Package_DFN_QFN:Texas_RDX0007A_QFN-FCMOD-7-3.3x4mm-P0.5mm_4EPU2
1UJ20-C-H-G-MSMT-4B-P16-TRLIB_UJ20-C-H-G-MSMT-4B-P16-TR/:UJ20CHGMSMT4BP16TRJ5

More from anobli/beal-hw

1
  • 2 layers112 × 38 mmBeal RX, the printed circuit board in 3D

    Beal RX

    anobli/beal-hw

    Kicad project for a Lora valves controller

    81 partsCERN-OHL-S-2.0

Similar boards

  • 6 layers110 × 96 mmAssembly preview, the printed circuit board in 3D

    Assembly preview

    ripclap/rm520n-carrier

    KiCad RM520N-GL carrier with 2.5 GbE, passive PoE, dual SIM interfaces and independent LoRa management.

    446 partsCERN-OHL-P-2.0
  • 2 layers70 × 70 mmCrawler pi charger, the printed circuit board in 3D

    Crawler pi charger

    christianarrer/crawler-pi-hardware

    Contains electronic PCB designs and 3D-printable parts for the crawler-pi autonomous tracked robot. Copy

    47 partsGPL-3.0
  • 4 layers67.5 × 96.6 mmBasicSTM32, the printed circuit board in 3D

    BasicSTM32

    MikeMcPherson/BasicSTM32F3

    Basic STM32F3 board for testing and development

    67 partsMIT
  • 4 layers35 × 42.5 mmBluetooth Channel Sounding Tag, the printed circuit board in 3D

    Bluetooth Channel Sounding Tag

    JaphD/Phasetag

    Compact nRF54L15 Bluetooth Channel Sounding tag with dual PCB antennas, motion sensing, and rechargeable power management. Designed in KiCad 10.

    71 parts
  • 6 layers22 × 80 mmM2SmartHome, the printed circuit board in 3D

    M2SmartHome

    lukasznowarkiewicz/M2SmartHome

    Setting up a smart home hub, such as running Home Assistant, often requires hardware with sufficient performance and connectivity options.

    257 parts2
  • 6 layers160 × 100 mmAwohali, the printed circuit board in 3D

    Awohali

    DeepSpace00/Awohali

    An open soure GNSS station for flash flood nowcasting

    556 parts
  • 8 layers110 × 90 mmLpddr4-test board, the printed circuit board in 3D

    Lpddr4-test board

    Singleboardcomputer/hardware_for_kintex

    495 parts1

Questions

How big is the Beal TX PCB?

It measures 69 × 56.8 mm and has 2 copper layers, 1.58 mm thick.

What parts does the Beal TX use?

93 parts, built around the LORA-E5-HF, DRV8912QPWPRQ1, LM5157QRTERQ1 and TPSM863253RDXR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Beal TX KiCad files?

From the anobli/beal-hw repository on GitHub, at the commit this page was made from: the board is Beal-TX/Beal-TX.kicad_pcb and its schematic Beal-Rx/Beal-RX.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Beal TX design in my own project?

Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).