

Numitron clock rotated numitrons
Rpo for pcb layouts, gerber and gcode files
- Size
- 120 × 50.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 24
- Nets
- 66
- Pads
- 187
- Tracks, vias
- 625, 21
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 18 Jun 2018
- Updated
- 30 Aug 2022
Overview
Numitron clock rotated numitrons is an open-source printed circuit board by androiders, from the androiders/pcbs repository on GitHub. It is a 2-layer board of 120 × 50.2 mm with 24 parts on 66 nets, routed with 625 tracks and 21 vias.
It is built around the ATMEGA8L-8AU and TPIC6595N. Its parts include 5 ICs, 4 connectors, 3 resistors, 3 switches and 2 capacitors. It belongs with the lEDs and displays boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATMEGA8L-8AU
TQFP-32(7x7)-40℃~+85℃ 10bit 1KB 2.7V~5.5V 23 512Byte 8 Bit 8KB 8MHz AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)TPIC6595N
PDIP-20-40℃~+125℃ 1 4.5V~5.5V 8 Open Drain Serial-to-Serial or Parallel TPIC PDIP-20 Shift Registers ROHSTexas InstrumentsShift Registers
README
README.mdView this project on CADLAB.io.
pcbs
Repo for pcb layouts, gerber and gcode files
Ki-Cad
PCB layout:
- Use as wide traces as possible. 1mm preffered.
- Dont use "filled areas" if possible. It does not make good geometry in flatcam
- Don't forget to set origin marker
- Export gerber: use auxiliary axis
FlatCam
geometry generation:
- If you are using thru-hole components or using bottom layer, mirror around y axis for both geometry and Drilling
- Edit drill files if necessary for fewer drill sizes
- TODO: test double sided layout by mirroring around center axis!
Isolation generation:
-
Current isolation mill depth to test: 0.04 mm (0.05 was tested and seems to work fine!) (Common copper depth is about 0.03 mm)
-
Current feedrate on isolation milling to test: 60 mm/s
-
spindle speed 12000 rpm
-
use 0.2 mm tool width on cnc generation
-
2 passes with 0.1 overlap
Cutout generation:
- Current cutout mill depth: 1.6 mm
- Current feedrate on cutout milling: 40 mm/s
- spindle speed 12000 rpm
FlatCam defaults:
- put a link in ~/.FlatCAM/defaults.json
bCNC
Probe:
- Fastfeed: 120
- Probefeed: 25
- Probe points: 4/cm (in each direction)
Drilling:
- Current drill plunge rate to test 20 mm/s
- spindle speed: 12000 rpm
- Drill depth: 1.6
Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | Numitron_IV-9 | Numitron:numitron iv-9 | NU1, NU2, NU3, NU4 |
| 4 | TPIC6595 | Package_DIP:DIP-20_W7.62mm_LongPads | U1, U2, U3, U4 |
| 3 | R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R2, R3 |
| 2 | C | Capacitor_THT:C_Disc_D3.8mm_W2.6mm_P2.50mm | C1, C2 |
| 2 | LED | LED_THT:LED_D5.0mm | D1, D2 |
| 1 | 5v in | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MKDS-1,5-2-5.08_1x02_P5.08mm_Horizontal | J3 |
| 1 | ATmega8L-8A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U5 |
| 1 | AVR-ISP-6 | Connector_IDC:IDC-Header_2x03_P2.54mm_Vertical | J1 |
| 1 | Crystal | Crystal:Crystal_Round_D1.5mm_Vertical | Y1 |
| 1 | RST | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW1 |
| 1 | Set H | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW3 |
| 1 | Set M | Button_Switch_SMD:SW_SPST_CK_RS282G05A3 | SW2 |
| 1 | UART | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | rtc | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J2 |
More from androiders/pcbs
12- 2 layers58 × 80 mm

- 2 layers

- 2 layers

- 2 layers

- 2 layers65.3 × 48.5 mm

- 2 layers

- 2 layers

- 2 layers44 × 50 mm

- 2 layers73.7 × 34.3 mm

- 2 layers

- 2 layers

- 2 layers

Similar boards
- 2 layers52.2 × 79 mm

Programmable light
dilshan/programmable-light
Simple time based programmable light controller
55 parts5MIT - 2 layers35 × 39.5 mm

RasPagerC9000
rwth-afu/RasPagerC9000
Adapted Version of RasPager to generate Signals for Ericsson C9000 Paging Transmitter
29 parts5 - 2 layers64.5 × 39.9 mm

- 2 layers32.4 × 32.8 mm

Analog Mixed Signal PCB
niyathiarun/Analog-Mixed-Signal-PCB
Analog–Mixed Signal PCB project featuring ATmega8L microcontroller and op-amp interface, designed and fabricated using KiCad.
12 parts1 - 2 layers120.1 × 46 mm

- 2 layers60.1 × 42.3 mm

TermoHumi
LinJesUxUs/TermoHumi
Thermo-hygrometer code, powered on ATMega, AHT10 sensor and 7 Segment Display.
91 parts - 2 layers44 × 16 mm

- 2 layers133.4 × 28.4 mm

Controlled generator schematics
alextousss/3d_ultrasonic_scanner
An ultrasonic 3D scanner
56 parts86GPL-3.0
Questions
How big is the Numitron clock rotated numitrons PCB?
It measures 120 × 50.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Numitron clock rotated numitrons use?
24 parts, built around the ATMEGA8L-8AU and TPIC6595N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Numitron clock rotated numitrons KiCad files?
From the androiders/pcbs repository on GitHub, at the commit this page was made from: the board is numitron clock/numitron clock-rotated-numitrons.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Numitron clock rotated numitrons design in my own project?
Its repository states no licence, so its author keeps all rights: ask androiders before reusing the design.