Skip to the content
2 layers93.9 × 83.8 mmBackplane, the printed circuit board in 3D

LoRa Wan Server to send data to a private InfluxDB

Size
93.9 × 83.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
67
Nets
61
Pads
196
Tracks, vias
383, 12
Pours
4
Routed
Yes
KiCad
KiCad 4
Created
19 Sep 2017
Updated
19 Sep 2017

Overview

Backplane is an open-source printed circuit board by AndreaGini, from the AndreaGini/DPW-Mesh-LoraWan repository on GitHub. It is a 2-layer board of 93.9 × 83.8 mm with 67 parts on 61 nets, routed with 383 tracks and 12 vias.

It is built around the SHT21. Its parts include 13 resistors, 6 diodes, 6 connectors, 5 ICs and 5 transistors.

Main components

1

README

ic880a-backplane/README.md

iC880A + Raspberry Pi Backplane

Buy this board at shop.coredump.ch!

This is a backplane to connect an iC880A-SPI concentrator board to a Raspberry Pi. It is inspired by the iC880A backplane by @gonzalocasas, but aims to give you the following additional features:

Power

  • Screw terminal and footprint for MP1584 step-down regulator module (6.7-28V)
  • Screw terminal for direct power input/output (5V)
  • Protection diode and resettable polyfuse against high voltage spikes
  • Protection against reverse polarity power input

Headers

  • Full access to Raspberry Pi GPIO header
  • Pin header for serial communication (RX/TX)
  • 2 Pin headers for I²C based sensors (SDA/SCL/GND/3.3V/5V)

Sensors

  • A SHT21 temperature/humidity sensor
  • An MCP3425 16-bit ADC to measure RPi supply voltage

Other

  • Pin header with flyback diode for 5V fan (5V/GND)
  • General purpose button connected to GPIO pin (e.g. for controlled Raspi shutdown)
  • Three general purpose SMD LEDs (Note: Only usable from Raspi versions with 40-pin GPIO header)
  • Mounting holes for Raspberry Pi B+ / 2B / 3B / Zero

PCB

Rendered

Rendered

Schematics

See schematics-v1.1.pdf.

Development

This PCB was created using KiCad 4.

Make sure that you clone all submodules:

text
git submodule init
git submodule update

License

© 2017 Danilo Bargen. Licensed under the TAPR Open Hardware License (www.tapr.org/OHL).

If you make any modification to this board, it would be great if you could let me know at mail@dbrgn.ch.

Parts

67
QtyValueFootprintReferences
10RResistors_SMD:R_1206R1, R2, R3, R4, R5, R6, R7, R8, R9, R13
4Q_NMOS_GSDTO_SOT_Packages_SMD:SOT-23Q1, Q2, Q3, Q4
3LED_SmallLEDs:LED_1206D1, D2, D3
3RResistors_SMD:R_0805R10, R11, R12
2CCapacitors_SMD:C_1206C1, C3
2DDO214:DO-214ACD4, D6
2I2Cheaders:header_1x5_unmarkedJ1, J2
2PWRConnectors_Terminal_Blocks:TerminalBlock_Pheonix_MPT-2.54mm_2polJ4, J5
1Ccapacitor-unmarked:CAP_UNMARKEDC2
1D_TVSDO214:DO-214AAD5
1FANheaders:header_1x2_markedJ6
1IC880A-SPIic880a:IC880A-SPIU2
1LOGOoshw-logos:OSHW_MASK_7MMG***
1MCP3425A0T-E/CHTO_SOT_Packages_SMD:SOT-23-6U5
1MP1584_MODULEregulators:MP1584_MODULEU4
1PolyfuseCapacitors_SMD:C_1812F1
1Q_PMOS_GSDTO_SOT_Packages_SMD:SOT-23Q5
1Raspberry_Pi_2_3Pin_Headers:Pin_Header_Straight_2x20_Pitch2.54mmU1
1SERheaders:header_1x2_unmarkedJ3
1SHT21sensirion:SHT21U3
1SW_Pushbuttons:SW_MikroshopSW1

The 41 most common of 67 parts.

Similar boards

  • 4 layers150 × 72 mmFIAControl, the printed circuit board in 3D

    FIAControl

    CatoLynx/LCD-FIA

    Custom hardware and software for a LCD platform passenger information display

    110 parts7
  • 2 layers100 × 30 mmPcb esp, the printed circuit board in 3D

    Pcb esp

    josefadamcik/RoomMonitorPcb

    A PCB design for RoomMonitor

    26 parts5MIT
  • 2 layersCepelin, the printed circuit board in 3D

    Cepelin

    frizider-si/delavnice

    opisi delavnic in materiali

    18 parts2
  • 2 layers56 × 90 mmWatertemp v1, the printed circuit board in 3D

    Watertemp v1

    gfroerli/hardware

    PCB and other hardware stuff in the watertemp project.

    61 parts1
  • 2 layers41 × 41.1 mmSensor logger, the printed circuit board in 3D

    Sensor logger

    hsl25/Sensor-Logger-PCB

    PCB design project - the sensor logger board features an IMU, temperature and humidity sensor, LCD screen and micro-SD card data storage.

    60 parts1
  • 4 layers90 × 140 mmEeg hardware v1, the printed circuit board in 3D

    Eeg hardware v1

    es-ude/eeg-hardware

    Repo of the Custom Hardware Design Files of the EEG-based Gaming Controller

    460 partsMIT
  • 2 layers103.8 × 122 mmPrueba1, the printed circuit board in 3D

    Prueba1

    francojsantander22-afk/main_board_habp

    Placa principal (main board) del sistema de adquisición de datos y telemetría para un globo meteorológico de alta altitud (HABP – High Altitude Balloon Project), diseñada en KiCad.

    26 parts
  • 4 layers140 × 54 mmPicoclock, the printed circuit board in 3D

    Picoclock

    locked/picoclock

    This repo is an attempt at building a Pico based alarm clock. It was created for my kids and features:

    146 parts

Questions

How big is the Backplane PCB?

It measures 93.9 × 83.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Backplane use?

67 parts, built around the SHT21. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Backplane KiCad files?

From the AndreaGini/DPW-Mesh-LoraWan repository on GitHub, at the commit this page was made from: the board is ic880a-backplane/backplane.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Backplane design in my own project?

Its repository states no licence, so its author keeps all rights: ask AndreaGini before reusing the design.