2 layers312.5 × 122.3 mm
2 layers19.9 × 29 mm
Rpipico
ambraglow/proto20406- Size
- 19.9 × 29 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 41
- Nets
- 59
- Pads
- 248
- Tracks, vias
- 464, 17
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 2 Jul 2023
- Updated
- 20 Jul 2024
Overview
Rpipico is an open-source printed circuit board by ambraglow, from the ambraglow/proto2040 repository on GitHub. It is a 2-layer board of 19.9 × 29 mm with 41 parts on 59 nets, routed with 464 tracks and 17 vias.
It is built around the RP2040, W25Q128JVSIQ and AP2112K-3.3. Its parts include 16 capacitors, 10 connectors, 8 resistors, 4 ICs and 1 diode. It belongs with the RP2040 boards of this library.
Main components
3
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
AP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorised
README
README.mdThis is proto2040, an rp2040 based board.
Parts
41| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0201_0603Metric | C4, C5, C6, C7, C8, C9, C10, C11, C12, C14 |
| 2 | 10uF | Capacitor_SMD:C_0402_1005Metric | C1, C2 |
| 2 | 1K | Resistor_SMD:R_0402_1005Metric | R5, R9 |
| 2 | 1uF | Capacitor_SMD:C_0201_0603Metric | C3, C13 |
| 2 | 27.4 | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | 27pF | Capacitor_SMD:C_0201_0603Metric | C15, C16 |
| 2 | 5.1K | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | Conn_01x02 | Connector_PinHeader_1.00mm:PinHeader_1x02_P1.00mm_Vertical | J2, J9 |
| 2 | Conn_01x04 | Connector_PinHeader_1.00mm:PinHeader_1x04_P1.00mm_Vertical | J5, J10 |
| 2 | Conn_01x13 | Connector_PinHeader_1.00mm:PinHeader_1x13_P1.00mm_Vertical | J3, J4 |
| 1 | 10K | Resistor_SMD:R_0402_1005Metric | R8 |
| 1 | 12M | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1K | Resistor_SMD:R_0201_0603Metric | R6 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | Conn_01x02 | Connector_PinHeader_1.27mm:PinHeader_1x02_P1.27mm_Vertical | J8 |
| 1 | Conn_01x03 | Connector_PinHeader_1.27mm:PinHeader_1x03_P1.27mm_Vertical | J6 |
| 1 | Conn_01x04 | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | J7 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LOGO | drawings:cute | G*** |
| 1 | RP2040 | MCU_RaspberryPi_and_Boards:RP2040-QFN-56 | U3 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 1 | W25Q128JVS | Package_DFN_QFN:DFN-8-1EP_3x2mm_P0.5mm_EP1.3x1.5mm | U1 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.23x5.23mm_P1.27mm | U2 |
Similar boards
- 2 layers120 × 25 mm
Grooveboard rp
ianklug/grooveboard
A four-key mechanical keyboard for rhythm games.
47 parts58CC-BY-SA-4.0 - 2 layers220 × 70 mm
Bemini rp
ianklug/bemini
A miniature mechanical keyboard controller with a rotary encoder for staggered-key rhythm games.
70 parts55CC-BY-SA-4.0 - 2 layers84.2 × 100 mm
Fabpack out v5 8
yuz207/agentpad13
agentpad13 — open-source 13-key macropad for agentic work (RP2040, vial-qmk, planar joystick, Raw HID agent-status protocol)
126 parts41 - 2 layers100 × 90 mm
EncoderPad RP2040
jpconstantineau/EncoderPad_RP2040
The EncoderPad RP2040 is a Video Editing Macropad with a 60mm Encoder Wheel. This encoder is made of metal and feels like it will last forever. The EncoderPad uses 9 mechanical switches (Cherry MX type).
62 parts29 - 2 layers76 × 90 mm
- 2 layers75 × 55 mm
Wellfed bench
Isaac-Duarte/wellfed
Open firmware that runs the PETLIBRO Granary PLAF103 pet feeder on your own Wi-Fi: no cloud, no account. Early and in testing.
93 parts8MIT - 2 layers42 × 42 mm
LoadcellSensor
jujojujo2003/Ender-3-3DPrinter-Load-Cell-Bed-Leveling-Sensor
This is a Load Cell based bed leveling sensor based on the RP2040 and TI ADS1235 ADC that should mount onto any vertical MGN12H gantry. My printer is an Ender 3 with a bunch of linear rail mods.
56 parts5MIT
Questions
How big is the Rpipico PCB?
It measures 19.9 × 29 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Rpipico use?
41 parts, built around the RP2040, W25Q128JVSIQ and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rpipico KiCad files?
From the ambraglow/proto2040 repository on GitHub, at the commit this page was made from: the board is rpipico.kicad_pcb and its schematic rpipico.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rpipico design in my own project?
Its repository states no licence, so its author keeps all rights: ask ambraglow before reusing the design.