Skip to the content
2 layersCtrl brd reduced, the printed circuit board in 3D

Tomizawa FZ-880B soldering station controller open-source firmware

Copper layers
2
Thickness
1.6 mm
Parts
14
Nets
14
Pads
37
Tracks, vias
70, 0
Routed
Yes
KiCad
KiCad 3
Created
10 Mar 2015
Updated
12 Jul 2015

Overview

Ctrl brd reduced is an open-source printed circuit board by alsav, from the alsav/stm8-soldering-station-controller repository on GitHub. It is a 2-layer board with 14 parts on 14 nets, routed with 70 tracks and 0 vias.

It is built around the STM8S003F3P6. Its parts include 11 connectors, 2 capacitors and 1 IC. It belongs with the STM8 boards of this library.

Main components

1

README

README.md

Tomizawa FZ-880B soldering station controller open-source firmware

Цель данного проекта - реанимация умершего чуда китайской инженерной мысли: паяльника с терморегуляцией Tomizawa FZ-880 и его клонов. Т.к. схемотехника агрегата мягко говоря не очень, возможно еще кому-то пригодится...

Итак, самое слабое место - схема питания МК. Если паяльник перестал подавать признаки жизни и при включении в розетку монотонно горят один илн несколько светодиодов - ваш случай.

Для восстановления потребуется:

  1. Прокачать до второго уровня или выше схему питания микроконтроллера (см.фото).
  2. Изготовить методом лута печатку под новый МК STM8S003F3P6, прикупив последний где-нибудь тут: http://www.ebay.com/sch/i.html?&_nkw=stm8s003f3
  3. Прошить МК и установить плату вместо стокового контроллера на свободное место.

Файлы:

  1. firmware_vX.X.hex - сама прошивка.
  2. ctrl-brd_reduced-F_Cu.ps - шаблон для изготовления платы (формат post-script).
  3. Все остальное - если будете заморачиваться с допилкой под сови нужды и повторной сборкой.

Для компиляции использовался sdcc 3.4.3 #9179 под linux (ubuntu 14.04). Для шитья - Versaloon (в проекте) или более доступное средство: ST_Link V2.

Features:

  1. Термостабилизация ПИД-регулятором. Точность 5-10С.
  2. Предварительный прогрев до температуры режима n+1 для сокращения времени нагрева жала.
  3. Индикация выхода на рабочий температурный режим миганием светодиода.
  4. Отключение паяла длинным нажатием.

TODO (если будет не лень):

  1. Режим калибровки: точная подстройка температуры с сохранением в eeprom.

Parts

14
QtyValueFootprintReferences
1CSM0603_CapaC2
1CSM0805C1
1GNDPIN_ARRAY_1P9
1HEATPIN_ARRAY_1P2
1LCDPIN_ARRAY_3X1P10
1NRSTPIN_ARRAY_1P4
1SENSEPIN_ARRAY_1P1
1STM8S003F3Ptssop-20IC1
1SWPIN_ARRAY_1P12
1SWIMPIN_ARRAY_1P5
1UART_TXPIN_ARRAY_1P6
1VDDPIN_ARRAY_1P8
1XPIN_ARRAY_1P11
1ZEROPIN_ARRAY_1P3

Similar boards

  • 2 layers87 × 71 mmSocket, the printed circuit board in 3D

    Socket

    eddyem/STM8_samples

    Some code samples and ready projects based on STM8 (deprecated)

    89 parts80
  • 2 layers32.1 × 41.2 mmIr signalgen lite, the printed circuit board in 3D

    Ir signalgen lite

    dilshan/ir-clone

    Open-source infrared remote control signal analysis and generating tool

    40 parts58MIT
  • 4 layers26.4 × 56 mmRPI5-SDexpress Hat, the printed circuit board in 3D

    RPI5-SDexpress Hat

    will127534/RPI5-SDexpress-Hat

    ctrl-c "RPI5-CFE-Hat" ctrl-v "RPI5-SDexpress-Hat"

    51 parts37MIT
  • 4 layers65 × 56 mmRPI5-CFE Hat, the printed circuit board in 3D

    RPI5-CFE Hat

    will127534/RPI5-CFE-Hat

    CFexpress Card hat for Raspberry Pi 5

    59 parts25MIT
  • 4 layersKvm base, the printed circuit board in 3D

    Kvm base

    thatoddmailbox/kvm-base

    The main board for the open-source HDMI KVM switch I built.

    70 parts19
  • 2 layers72.8 × 32 mmMicro fm radio, the printed circuit board in 3D

    Micro fm radio

    dilshan/rda5807-fm-radio-module

    RDA5807M based stereo FM radio receiver

    56 parts8MIT
  • 2 layers65 × 56 mmRas pi supercap ups, the printed circuit board in 3D

    Ras pi supercap ups

    akuker/SuperUPS

    This is a fork of the original Supercapacitor UPS board for a Raspberry Pi by Scott Baker, http://www.smbaker.com/

    88 parts7

Questions

What parts does the Ctrl brd reduced use?

14 parts, built around the STM8S003F3P6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Ctrl brd reduced KiCad files?

From the alsav/stm8-soldering-station-controller repository on GitHub, at the commit this page was made from: the board is brd/ctrl-brd_reduced.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Ctrl brd reduced design in my own project?

Its repository states no licence, so its author keeps all rights: ask alsav before reusing the design.