

Mixer
read-only mirror
- Size
- 80.8 × 110 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 76
- Nets
- 60
- Pads
- 235
- Tracks, vias
- 393, 37
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 15 Jun 2024
- Updated
- 7 Sep 2026
Overview
Mixer is an open-source printed circuit board by Alloyed, from the Alloyed/KitsBlips repository on GitHub, published under the MIT licence. It is a 2-layer board of 80.8 × 110 mm with 76 parts on 60 nets, routed with 393 tracks and 37 vias.
It is built around the TL072, B10K and SS14. Its parts include 40 resistors, 9 connectors, 6 capacitors, 2 ICs and 2 diodes. It belongs with the audio and music boards of this library.
Main components
3TL072
SOP-8-18V~18V 0℃~+70℃ 1.4mA 1.5nA 10V/us 10mV 2 2.5nA 3MHz 85dB SOP-8 Operational Amplifier ROHSGcoreOperational AmplifierB10K
RES-TH_RK10J12E002LTH-3P SMT ROHSJLCPCB AssemblyUncategorisedSS14
SMA(DO-214AC)-55℃~+150℃ 1A 25A 300uA@40V 40V 550mV@1A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
README
README.mdKitsBlips
Monorepo for my Eurorack/synthesizer hobby projects! (that's me, I'm kit)
Everything is always in a state of "not-quite-finished". if something is unclear or unusable in its current state, and you want to use it, feel free to open an issue or contact me.
For technical reasons, this project is ordered by toolset and not by module. this means the full source for a single module may be across multiple folders! Sorry.
unless otherwise listed, all code is MIT licensed. All hardware designs and graphics (kicad, svg etc) are CC-BY-SA 4.0.
Building/Installing
Each project/folder has a specific readme that includes extra steps if necessary, but in general, builds are managed using cmake.
$ mkdir -p <folder>/build && cd <folder>/build
$ cmake .. -DCMAKE_BUILD_TYPE=<build type: Debug, MinSizeRel, RelWithDebInfo>
$ cmake --build . --config=<the build type>
$ cmake --install . --prefix <location> # if the target supports installation
$ ctest # if the target has unit testsonce you have all your configurations set up, you can quickly rebuild all/run tests using rebuild-all.sh.
Projects
For Hardware:
For VCV Rack:
- /vcvrack
- Modules for VCV Rack
For DAWS:
- /daw
- Modules for DAWS (VST3/CLAP plugins)
- /clapeze
- Microframework for writing clap plugins
- /kitgui
- UI library for clap plugins
Shared:
- /panels
- Art/Panel designs.
- /kitdsp
- Shared DSP code, runs on all platforms
- /kitdsp-gpl
- DSP code with GPL algorithms. This is the only folder that comes with extra license restrictions!
AI statement
KitsBlips will not accept PRs that are generated wholly or in significant part by generative AI. Future development will not use Generative AI.
There are a few older commits where I tried it for automatic refactoring, found it less than successful, and cleaned it up afterward. You can try the same thing; I wouldn't be able to tell the difference probably, but my conclusion to that experiment was that it wasn't worth it at the time.
Parts
76| Qty | Value | Footprint | References |
|---|---|---|---|
| 18 | 100k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R10, R11, R12, R14, R15, R16, R20, R21, R22, R24, R27, R30, R31, R32, R36, R37 +2 |
| 17 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R5, R6, R7, R8, R13, R17, R18, R19, R25, R26, R29, R33, R34, R35, R39 +1 |
| 10 | A10k | KitsBlips:Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | RV1, RV2, RV4, RV6, RV8, RV9, RV11, RV12, RV14, RV15 |
| 5 | B10k | KitsBlips:Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | RV3, RV5, RV10, RV13, RV16 |
| 5 | MONO_IN | KitsBlips:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J1, J2, J4, J7, J8 |
| 4 | 0.1uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3, C4, C5, C6 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R4 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 2 | 4k7 | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R23, R28 |
| 2 | SS14 | Diode_SMD:D_SMA | D1, D2 |
| 1 | A10k | KitsBlips:Potentiometer_Alpha_RD902F-40-00D_Dual_Vertical | RV7 |
| 1 | EURO_PWR_2x5 | KitsBlips:Pins_2x05_2.54mm_TH_Europower_shrouded | J12 |
| 1 | MIX_L | KitsBlips:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J5 |
| 1 | MIX_R | KitsBlips:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J6 |
| 1 | SEND_L | KitsBlips:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | J3 |
| 1 | TL072 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | TL074 | Package_SO:SOIC-14_3.9x8.7mm_P1.27mm | U1 |
The 75 most common of 76 parts.
More from Alloyed/KitsBlips
10- 2 layers150 × 100 mm

- 2 layers84 × 100 mm

- 2 layers40 × 110 mm

- 2 layers80.8 × 110 mm

- 2 layers70.7 × 21.1 mm

- 2 layers19.9 × 100 mm

- 2 layers60.5 × 100 mm

- 2 layers80.8 × 110 mm

- 2 layers70 × 100 mm

- 2 layers91 × 50 mm

Similar boards
- 2 layers80 × 54.5 mm

- 2 layers100 × 83.5 mm

Dual Delay
soggybag/Dual-Delay
Two PT2399 delay lines with a TWIST knob blending self and cross feedback (Super-Freq)
121 parts - 2 layers100 × 83.5 mm

Loop Echo
soggybag/Loop-Echo
A single-PT2399 delay with an effects loop in the feedback path: - only the repeats circulate through the loop; - the first echo is clean, and each later echo goes through the external effect again: fuzz degrades, a…
90 parts - 2 layers53 × 52.1 mm

UglyFace 03
soggybag/Ugly-Face-3-SMD
A gated, envelope-controlled square-wave synth fuzz for guitar, in a Hammond 1590B. A TL072 preamp (gain 201) gates and bends a TLC555 oscillator, with a MIX control to blend the dry fuzz with the synth tone.
84 parts - 2 layers48.4 × 106.3 mm

- 2 layers60 × 110 mm

- 2 layers38 × 100 mm

- 2 layers40 × 99 mm

Questions
How big is the Mixer PCB?
It measures 80.8 × 110 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Mixer use?
76 parts, built around the TL072, B10K and SS14. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Mixer KiCad files?
From the Alloyed/KitsBlips repository on GitHub, at the commit this page was made from: the board is kicad/mixer/mixer.kicad_pcb and its schematic kicad/4knobs/4knobs.circuitjs.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Mixer design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).