Skip to the content
2 layers73.7 × 39.4 mmPower distributor, the printed circuit board in 3D

Power distributor

alexdrymonitis/3dPd31

Digital modular hardware/software synthesizer project based on Pure Data and Arduino

Size
73.7 × 39.4 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
3
Pads
21
Tracks, vias
39, 0
Pours
1
Routed
Yes
KiCad
KiCad 4
Created
11 Aug 2016
Updated
3 May 2018

Overview

Power distributor is an open-source printed circuit board by alexdrymonitis, from the alexdrymonitis/3dPd repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 73.7 × 39.4 mm with 12 parts on 3 nets, routed with 39 tracks and 0 vias.

It is built around the LD1117S33TR(MS). Its parts include 9 connectors, 2 capacitors and 1 IC. It belongs with the audio and music boards of this library.

Main components

1

README

README.md

3dPd

This repository hosts the code, schematics, and circuit board designs made in Kicad, for a hardware digital modular synthesizer. The audio is programmed in Pure Data and the hardware control in the Arduino language. This synthesizer is supposed to run on a Raspberry Pi 3 and a Teensy3.2. You're welcome to use any other hardware you like, but this specific hardware is supported and explained here.

Note about the Arduino code

Go to the Arduino_code directory and read the README.txt file first. That should give you enough information about the Arduino code. Do that before you start reading the Pd patches.

Note about the Pd patches

The heart of this project is the modular_synthesizer.pd patch. Open it and you'll see some other abstractions in there. Go into the [pd modules] sub-patch and look inside. Each module must have its own abstraction. There are some tutorial module abstractions which show you how to build your own. Open them and read them carefully.

There's also a debug.pd patch which helps with debugging by showing input from the Teensy and printing various message concerning module connections and LED states.

Dependencies

This project uses the following external libraries:
zexy
comport
iemmatrix
iemguts
ggee
list-abs
tabreceive_mult~

The first five libraries are being installed with "apt-get" and the last two are installed through Deken (In Pd got to Help -> Find externals and type these two names -one at a time-, the highlighted version(s) is good for your system).

Pd-0.47.0 or higher is required.

General note

I'll upload a wiki with instructions for creating the hardware of a module and the whole system. It's in my TODO list, which will hopefully happen in the near future. You can watch a demo video of the synthesizer here https://www.youtube.com/watch?v=HD13bDPyBWA

Parts

12
QtyValueFootprintReferences
5CONN_01X02Connect:bornier2P1, P2, P3, P4, P5
4CONN_01X01mydrillhole:holeP6, P7, P8, P9
1100nFCapacitors_ThroughHole:C_Rect_L4_W2.5_P2.5C1
110uFCapacitors_ThroughHole:C_Radial_D5_L6_P2.5C2
1LD1117S33TRTO_SOT_Packages_THT:TO-220_Neutral123_Vertical_LargePadsU1

More from alexdrymonitis/3dPd

5
  • 2 layers105.4 × 57.2 mmPower bus, the printed circuit board in 3D

    Power bus

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    25 parts31GPL-3.0
  • 2 layers26.7 × 90.8 mmModule specific board2, the printed circuit board in 3D

    Module specific board2

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    18 parts31GPL-3.0
  • 2 layers24.1 × 77.5 mmModule generic top board, the printed circuit board in 3D

    Module generic top board

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    16 parts31GPL-3.0
  • 2 layers64.8 × 45.7 mmTeensy mother board, the printed circuit board in 3D

    Teensy mother board

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    13 parts31GPL-3.0
  • 2 layers24.1 × 77.5 mmModule generic bottom board, the printed circuit board in 3D

    Module generic bottom board

    alexdrymonitis/3dPd

    Digital modular hardware/software synthesizer project based on Pure Data and Arduino

    7 parts31GPL-3.0

Similar boards

  • 2 layers65 × 56 mmMMDVM HS Dual Hat, the printed circuit board in 3D

    MMDVM HS Dual Hat

    phl0/MMDVM_HS_Dual_Hat

    Duplex variant of MMDVM_HS_Hat

    216 parts218
  • 2 layers100 × 100 mmWifi PB panel, the printed circuit board in 3D

    Wifi PB panel

    AntonioMR/Wifi-Play-Board

    Placa de experimentacion para el ESP12F (ESP8266)

    416 parts29
  • 2 layers65 × 56 mmMMDVM RPT Hat, the printed circuit board in 3D

    MMDVM RPT Hat

    mathisschmieder/MMDVM_RPT_Hat

    MMDVM_RPT_Hat for the Raspberry Pi

    119 parts27
  • 2 layersRobot MGR, the printed circuit board in 3D

    Robot MGR

    rayvburn/diff_drive_mapping_robot

    ROS driver for the Raspberry Pi based differential drive robot

    95 parts27
  • 4 layers111.8 × 80.8 mmPrototype1, the printed circuit board in 3D

    Prototype1

    nmikstas/atari_pokey

    Recreation of the Atari POKEY chip (work in progress)

    164 parts20
  • 4 layers45.5 × 50 mmAdapter, the printed circuit board in 3D

    Adapter

    strfry/LG360VR

    This about making the LG 360 VR Goggles usable with a normal DisplayPort outlet.

    58 parts19
  • 2 layers74.9 × 40.6 mmAnavi fume extractor, the printed circuit board in 3D

    Anavi fume extractor

    AnaviTechnology/anavi-fume-extractor

    Open source WiFi development board for a portable fume extractor with 5V USB-powered fan for absorbing smoke.

    34 parts17
  • 2 layers74.9 × 40.6 mmAnavi thermometer, the printed circuit board in 3D

    Anavi thermometer

    AnaviTechnology/anavi-thermometer

    WiFi Smart Thermometer with ESP8266, DHT22, DS18B20, OLED display and slots for up to 3 I2C sensor modules

    25 parts17

Questions

How big is the Power distributor PCB?

It measures 73.7 × 39.4 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Power distributor use?

12 parts, built around the LD1117S33TR(MS). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Power distributor KiCad files?

From the alexdrymonitis/3dPd repository on GitHub, at the commit this page was made from: the board is circuits/power_distributor/power_distributor.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Power distributor design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).