

open wound, the system behind the CUT artwork
- Size
- 45.1 × 26 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 24
- Nets
- 34
- Pads
- 99
- Tracks, vias
- 209, 22
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 3 Jun 2014
- Updated
- 20 Mar 2017
Overview
Slave is an open-source printed circuit board by akornsys-rdi, from the akornsys-rdi/open-wound repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 45.1 × 26 mm with 24 parts on 34 nets, routed with 209 tracks and 22 vias.
It is built around the ATMEGA328P-AU, LM78L05ACZ and BC847. Its parts include 9 capacitors, 5 resistors, 5 connectors, 2 ICs and 1 transistor. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
3ATMEGA328P-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LM78L05ACZ
TO-920℃~+125℃@(Tj) 1 100mA 20V 3mA 40uVrms 5V 62dB@(120Hz) Fixed Over Current Protection、Over Temperature Protection、Short Circuit Protection Positive TO-92 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBC847
SOT-231 NPN 100MHz 100mA 100nA 110 200mW 45V 500mV 6V NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)
README
README.mdopen-wound
_
___ _ __ ___ _ _ __ __ _____ _ _ _ _ __| |
/ _ \ '_ \/ -_) ' \ \ V V / _ \ || | ' \/ _` |
\___/ .__/\___|_||_| \_/\_/\___/\_,_|_||_\__,_|
|_| open wound, the system behind the CUT artwork.
ChangeLog
- Cambios generales:
- Ahora open wound está bajo licencia GPLv3.
- Open wound usa versionamiento semántico.
- Esclavos version 1.0.0:
- Cambios menores en PCB.
- El microcontrolador pasa a ser parte de la placa, no un módulo Arduino.
- Los pines sin usar son salidas a nivel bajo no conectadas en lugar de entradas a masa.
- Se añade un conector AVRISP de seis pines.
- Se añade un conector de debug.
- Placa diseñada en SMT..
- Mejorado el método de conexión a la plancha sensora.
- Ahora se usan conectores subminiatura con enclavamiento para su conexión.
- Maestro en versión 1.0.0-alpha:
- El maestro ahora dispone de catorce canales para esclavos.
- Se permiten cuatro canales para PIR compatibles con los esclavos.
- Cambiado el CI amplificador.
- Entrada de audio compacta medianteconector DA15F.
- Buffer digital trigger-schmitt para acondicionar la señar de los esclavos.
- Usa los propios LED del RJ45 para indicar conexión y dato entrante.
- Ahora usa FreeCanvas.
Parts
24| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 100nF | Capacitors_SMD:C_0603_HandSoldering | C4, C5, C7 |
| 2 | 10r | Resistors_SMD:R_0603_HandSoldering | R1, R2 |
| 2 | 22pF | Capacitors_SMD:C_0603_HandSoldering | C6, C8 |
| 1 | 100pF | Capacitors_SMD:C_0603_HandSoldering | C9 |
| 1 | 10k | Resistors_SMD:R_0805_HandSoldering | R3 |
| 1 | 10nF | Capacitors_SMD:C_0603_HandSoldering | C3 |
| 1 | 10uF | Capacitors_SMD:c_elec_5x5.3 | C1 |
| 1 | 16MHz | Crystals_Oscillators_SMD:Q_49U3HMS | X1 |
| 1 | 1M | Resistors_SMD:R_0805_HandSoldering | R4 |
| 1 | 1uF | Capacitors_SMD:c_elec_4x5.3 | C2 |
| 1 | 2k2 | Resistors_SMD:R_0805_HandSoldering | R5 |
| 1 | ATMEGA328P-A | Housings_QFP:TQFP-32_7x7mm_Pitch0.8mm | U2 |
| 1 | AVRISP | Pin_Headers:Pin_Header_Straight_2x03 | P1 |
| 1 | BC847 | Housings_SOT-23_SOT-143_TSOT-6:SOT-23_Handsoldering | Q1 |
| 1 | DEBUG | asrdi-conn:IL-Z-6PL-SMTYE | P4 |
| 1 | IO | asrdi-conn:IL-Z-8PL-SMTYE | P2 |
| 1 | LM78L05ACZ | Housings_SOT-89:SOT89-3_Housing_Handsoldering | U1 |
| 1 | PIEZO | asrdi-conn:IL-Z-2PL-SMTYE | P3 |
| 1 | SENSE | Wire_Pads:SolderWirePad_single_2mmDrill | P5 |
The 23 most common of 24 parts.
Similar boards
- 2 layers

- 2 layers99.1 × 60.3 mm

FTController
jbtronics/FTController
A Motor controller for Fischertechnik with many cool features.
94 parts5 - 2 layers44.5 × 23.4 mm

ProbUSBis a1
emdarcher/probUSBis_hardware
hardware files for probUSBis board, a custimized USB ATtiny85 board based on LittleWire and DigiSpark.
26 parts1 - 2 layers100 × 50 mm

Ebus adapter
sarfata/ebus-adapter
This is a read/write adapter for eBus heating bus. It can be connected to a USB-serial adapter (3.3V or 5V) - or to a Particle Photon.
32 parts - 2 layers14.6 × 13.1 mm

- 2 layers65 × 56 mm

CANHat
RobertPHeller/RPi-RRCircuits
A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading
29 parts24 - 2 layers80 × 66 mm

- 2 layers49.3 × 30.4 mm

Questions
How big is the Slave PCB?
It measures 45.1 × 26 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Slave use?
24 parts, built around the ATMEGA328P-AU, LM78L05ACZ and BC847. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Slave KiCad files?
From the akornsys-rdi/open-wound repository on GitHub, at the commit this page was made from: the board is brd/slave/slave.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Slave design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).