

Audio amp
Infra Red remote control amplifier
- Size
- 159 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 129
- Nets
- 93
- Pads
- 414
- Tracks, vias
- 1,649, 118
- Pours
- 16
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 19 Feb 2016
- Updated
- 19 Oct 2016
Overview
Audio amp is an open-source printed circuit board by ak1211, from the ak1211/IR-control-amp repository on GitHub, published under the MIT licence. It is a 2-layer board of 159 × 100 mm with 129 parts on 93 nets, routed with 1,649 tracks and 118 vias.
It is built around the ATMEGA328P-PU, LME49720NA and LM1972M, with the NDS9936, FDS4935 and LME49600TS among its other parts. Its parts include 46 resistors, 32 capacitors, 18 ICs, 11 connectors and 6 diodes. It belongs with the audio and music boards and the AVR (ATmega, ATtiny) boards of this library.
Main components
7ATMEGA328P-PU
DIP-28-300mil-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH DIP-28-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)LME49720NA
PDIP-8-17V~-2.5V、2.5V~17V -40℃~+85℃ 0.00003% 10mA 120dB 2-Channel PDIP-8 Operational Amplifier ROHSTexas InstrumentsAudio AmplifiersLM1972M
SOIC-20SOIC-20-300mil Audio Amplifiers ROHSTexas InstrumentsAudio Interface ICsNDS9936
SOIC-8-55℃~+150℃ 185pF 2 N-Channel 2W 30V 315pF 35nC@10V 3V 50mΩ@10V 525pF 5A N-Channel SOIC-8 MOSFETs ROHSonsemiMOSFETsFDS4935
SOIC-8-55℃~+175℃ 1.233nF 152pF 2 P-Channel 21nC@5V 2W 30V 311pF 35mΩ@4.5V 3V 7A P-Channel SOIC-8 MOSFETs ROHSonsemiMOSFETsLME49600TS
TO-263High Performance, High Fidelity, High Current Audio BufferTexas InstrumentsUncategorisedLMC6482IN
PDIP-8-40℃~+85℃ 0.02pA 1.3V/us 1.5MHz 1uV/℃ 2 2pA 30mA 37nV/√Hz@1kHz 3V~15.5V 3mV 700uA 82dB ESD protection、Reverse-phase input protection Rail-to-Rail Input, Rail-to-Rail Output PDIP-8 Precision Op Amps ROHSTexas InstrumentsPrecision Op Amps
README
README.mdIR-control-amp
Overview
Infra Red remote control amplifier firmware on atmega328p
Description
このソフトウエアはatmega328p使用
赤外線リモコンコントロールヘッドホンアンプ基板Rev: A2.x用
組込みファームウエアです。
Requirements
Atmel Studio 7 (Version: 7.0.594 - ) © 2015 Atmel Corp. All rights reserved.
Compile and Link
Atmel Studio 7でsolution file を開いてコンパイル&リンクを行ってください。
License
Author
Parts
129| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 10k | Resistors_SMD:R_0805_HandSoldering | R2, R6, R23, R24, R25, R26, R27, R29, R32, R35, R37, R43, R44, R45 |
| 14 | 1u(film) | Capacitors_SMD:C_1206_HandSoldering | C8, C9, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C27, C28 |
| 8 | 1k | Resistors_SMD:R_0805_HandSoldering | R11, R12, R17, R19, R20, R21, R28, R31 |
| 7 | 0.1u | Capacitors_SMD:C_0805_HandSoldering | C22, C23, C24, C25, C31, C32, C33 |
| 7 | 10 | Resistors_SMD:R_0805_HandSoldering | R1, R5, R22, R30, R33, R36, R42 |
| 6 | 22u(tantalum) | Capacitors_Tantalum_SMD:TantalC_SizeA_EIA-3216_HandSoldering | C4, C5, C6, C7, C29, C30 |
| 4 | 1M | Resistors_SMD:R_0805_HandSoldering | R13, R14, R15, R16 |
| 4 | NDS9936 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U2, U10, U12, U13 |
| 4 | P*** | toragi_201305:hole_m3 | hole_m3, hole_m3, hole_m3, hole_m3 |
| 3 | 1N4148W1 | Diodes_SMD:SOD-123 | D4, D5, D6 |
| 3 | 33k | Resistors_SMD:R_0805_HandSoldering | R3, R7, R46 |
| 3 | 4.7k | Resistors_SMD:R_0805_HandSoldering | R8, R38, R39 |
| 2 | 02CZ3.3(3.3V) | mylib_legacy:SC-59 | D2, D3 |
| 2 | 220u | Choke_SMD:Choke_SMD_10.4x10.4_H4.8 | L1, L2 |
| 2 | 330 | Resistors_SMD:R_0805_HandSoldering | R40, R41 |
| 2 | FDS4935 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U3, U17 |
| 2 | Jumper_NC_Small | Connect:GS2 | JP2, JP3 |
| 2 | LME49600 | mylib:LME49600 | U8, U9 |
| 2 | LME49720 | Housings_DIP:DIP-8_W7.62mm_LongPads | U5, U6 |
| 2 | TLP121 | Opto-Devices:Optocoupler_SMD_HandSoldering_KPC357_LTV35x_PC357_SingleChannel | U15, U16 |
| 2 | open | Capacitors_SMD:C_1206_HandSoldering | C10, C11 |
| 2 | open | Resistors_SMD:R_0805_HandSoldering | R9, R10 |
| 1 | 1.2k | Resistors_SMD:R_0805_HandSoldering | R34 |
| 1 | 100k | Resistors_SMD:R_0805_HandSoldering | R18 |
| 1 | 1ch IN | toragi_201305:AJ-1780 | J1 |
| 1 | 220u | Capacitors_SMD:c_elec_10x10.5 | C1 |
| 1 | 2SK2411 | Transistors_SMD:sot404 | Q1 |
| 1 | 2ch IN | toragi_201305:AJ-1780 | J2 |
| 1 | 33(2W) | Resistors_ThroughHole:Resistor_Horizontal_RM20mm | R4 |
| 1 | 47u | Capacitors_SMD:c_elec_10x10.5 | C2 |
| 1 | 8200u | Capacitors_ThroughHole:C_Radial_D18_L36_P7.5 | C3 |
| 1 | 8MHz | mylib:CERALOCK | Q2 |
| 1 | AMP_POWER | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM3-96mm_Lock_2pin_straight | P1 |
| 1 | ATMEGA328P-P | Housings_DIP:DIP-28_W7.62mm_LongPads | IC1 |
| 1 | AVRISP | mylib:AVRISP_Angled | P4 |
| 1 | BARREL_JACK | Connect:BARREL_JACK | CON1 |
| 1 | DISPLAY | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM2-54mm_Lock_4pin_straight | P5 |
| 1 | G5V2 | mylib:G5V-2 | inputRLY1 |
| 1 | GND_SUMMING_PT | mylib:GND_SUMMING_PT | G1 |
| 1 | LED | LEDs:LED-0805 | D1 |
| 1 | LM1972 | Housings_SOIC:SOIC-20_7.5x12.8mm_Pitch1.27mm | U7 |
| 1 | LMC6482 | Housings_DIP:DIP-8_W7.62mm_LongPads | U11 |
| 1 | MCWI03_12D05 | mylib:MINMAX_MCWI03-12x | U4 |
| 1 | MUTE | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM2-54mm_Lock_3pin_straight | P8 |
| 1 | NJU7223DL1 | Transistors_SMD:sot428 | U1 |
| 1 | OUT ch.L | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM2-54mm_Lock_2pin_straight | P2 |
| 1 | OUT ch.R | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM2-54mm_Lock_2pin_straight | P3 |
| 1 | PHONE OUT | toragi_201305:AJ-1780 | J3 |
| 1 | PL-IRM2161 | mylib:PL-IRM2161 | U14 |
| 1 | PolySW 1.85A | Fuse_Holders_and_Fuses:Fuse_TE5_Littlefuse-395Series | F1 |
| 1 | RESET | mylib:ALPS_TACT_SW_SKHHL | SW1 |
| 1 | R_ENC_SW_RGB_LED | mylib:EC12PLRGBSDHF | RE1 |
| 1 | STBY | Sockets_MOLEX_KK-System:Socket_MOLEX-KK-RM2-54mm_Lock_3pin_straight | P7 |
The 128 most common of 129 parts.
More from ak1211/IR-control-amp
1- 2 layers363.2 × 200 mm

Similar boards
- 2 layers98.4 × 48.3 mm

Wireclone
phenidone/appnote-amplifier
Headphone amplifier based on schematic in the LME49600 datasheet
53 parts - 2 layers71 × 71 mm

- 2 layers85 × 35 mm

- 2 layers210.3 × 120.7 mm

- 2 layers39.4 × 106.7 mm

Nearness
sarnesjo/nearness
Minimal panning mixer for the Eurorack modular synthesizer system
52 parts99 - 2 layers18.5 × 110 mm

Exits board A
ramphands/Exits
4hp DIY eurorack line and headphone output module based on the Nearness and AJH headphone amp modules
42 parts33 - 2 layers49.8 × 110 mm

Nearness
bmoren/attenuated-nearness
a 6hp variation of the nearness eurorack module which adds an attenuator to each input!
61 parts17 - 2 layers134 × 109.5 mm

FreeDSP SMD AB plus
CyberPit/FreeDSP_Classic_SMD_AB_plus-II
An extended version of FreeDSP Classic SMD A/B
233 parts6
Questions
How big is the Audio amp PCB?
It measures 159 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Audio amp use?
129 parts, built around the ATMEGA328P-PU, LME49720NA, LM1972M and NDS9936. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Audio amp KiCad files?
From the ak1211/IR-control-amp repository on GitHub, at the commit this page was made from: the board is PCB/audio_amp.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Audio amp design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).