

EMG hand sensor
emg HIL with arduino matlab manipulation of allegroHand
- Size
- 73.9 × 41.5 mm
- Copper layers
- 4
- Thickness
- 1.61 mm
- Parts
- 52
- Nets
- 66
- Pads
- 209
- Tracks, vias
- 402, 87
- Pours
- 3
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Jun 2025
- Updated
- 17 Jan 2026
Overview
EMG hand sensor is an open-source printed circuit board by ajama0609, from the ajama0609/emg_hand_manipulation repository on GitHub. It is a 4-layer board of 73.9 × 41.5 mm with 52 parts on 66 nets, routed with 402 tracks and 87 vias.
It is built around the STM32F103C8T6, MIC5504-3.3YM5 and USBLC6-2SC6, with the 3314G-1-101E among its other parts. Its parts include 20 capacitors, 9 resistors, 6 ICs, 5 connectors and 1 diode. It belongs with the sensors and measurement boards and the STM32 boards of this library.
Main components
4STM32F103C8T6
LQFP-48(7x7)-40℃~+85℃ 12bit 20KB 2V~3.6V 32 Bit 37 64KB 72MHz ARM Cortex-M3 Built-in FLASH LQFP-48(7x7) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)MIC5504-3.3YM5
SOT-23-5-40℃~+125℃@(Tj) 1 120uVrms 15uA 180mV@(300mA) 3.3V 300mA 5.5V 75dB@(1kHz) Fixed Over Temperature Protection、Enable Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTECH PUBLICVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)3314G-1-101E
SMD-3P,4.5x4.5mm1 100Ω 250mW ±100ppm/℃ ±20% SMD-3P,4.5x4.5mm Potentiometers, Variable Resistors ROHSBournsPotentiometers & Variable Resistors
README
README.mdEMG Hand Gesture Classification
Introduction
Surface electromyography (sEMG) is a non-invasive technique for measuring muscle electrical activity and is widely used in human–machine interfaces, prosthetics, and rehabilitation systems. Reliable sEMG systems require low-noise analog front-ends, high common-mode rejection, stable power delivery, and careful PCB layout to preserve signal integrity, particularly given the low-amplitude (µV–mV) nature of EMG signals.
This project details the design, fabrication, and validation of a custom surface electromyography (sEMG) acquisition board intended to capture high-fidelity muscle signals for both real-time and offline analysis. Bypassing commercial development kits, a fully custom printed circuit board (PCB) was developed to directly address the practical engineering challenges inherent in analog signal conditioning, proper grounding techniques, filtering, and the integration of mixed-signal systems ---
Hardware Development and Testing
A custom sEMG acquisition hardware board has been designed and fabricated to enable lightweight, low-latency, and high-fidelity signal capture for real-time applications.
Key Components and BOM Highlights:
- Instrumentation Amplifiers: Texas Instruments INA333 (3 units) for high CMRR and low noise EMG signal amplification
- Microcontroller: STM32F103C8T6 (ARM Cortex-M3) for signal processing and data acquisition
- Power Management: Microchip MIC5504-3.3 LDO regulator for stable 3.3V supply
- ESD Protection: STMicroelectronics USBLC6-2SC6 for USB interface protection
- Passive Components: High-quality capacitors (e.g., TDK X5R, KEMET), resistors (Susumu, Yageo), and ferrite bead (Murata) for noise filtering and stable operation
- Connectors: USB-C receptacle, 3.5mm audio jacks for signal output and power input
- Oscillator: EPSON 16MHz crystal for clock generation
Parts
52| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C3, C4, C5, C6, C16, C17, C18, C19, C20, C21 |
| 4 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C9, C11, C12 |
| 3 | 10k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R4 |
| 3 | 3.3k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R11, R12, R14 |
| 3 | 3314G-1-101E | Bourne_pot_smd:3314G-1 | VR1, VR2, VR4 |
| 3 | AudioJack3 | Connector_Audio:Jack_3.5mm_CUI_SJ-3523-SMT_Horizontal | J4, J5, J6 |
| 3 | Fiducial | Fiducial:Fiducial_0.5mm_Mask2mm | FID1, FID2, FID3 |
| 3 | INA333xxDGK | Package_SO:VSSOP-8_3x3mm_P0.65mm | U3, U4, U5 |
| 2 | 10p | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C14, C15 |
| 2 | 5k1 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R8, R9 |
| 2 | MountingHole_Pad | MountingHole:MountingHole_2.2mm_M2_Pad | H1, H2 |
| 1 | 100n | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C13 |
| 1 | 10nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C7 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | 120R | Ferrite_SMT:BLM21AG102BH1J | FB1 |
| 1 | 16MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 1k5 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5 | U6 |
| 1 | RED | Diode_SMD:D_0805_2012Metric | D1 |
| 1 | STM32F103C8T6 | Package_QFP:LQFP-48_7x7mm_P0.5mm | U2 |
| 1 | SW_SPDT | Button_Switch_SMD:SW_SPDT_CK_JS102011SAQN | SW1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U1 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
Similar boards
- 4 layers55 × 50 mm

- 4 layers40 × 30 mm

- 2 layers72.6 × 43.2 mm

MCUmeter
therealprof/MCUmeter-hardware
Kicad project files and gerbers for my MCUmeter project
31 parts6BSD-3-Clause - 2 layers91.4 × 99.1 mm

- 4 layers60 × 37 mm

- 4 layers72 × 59 mm

TestBench
ELEC70142-VLSI-Coursework/vlsi_test_platform
Validation environment for the VLSI SoC project. This repository integrates mechanical and PCB designs for a dedicated testrig with FPGA-based gateware and Python-driven software abstractions to facilitate full-chip…
69 parts1 - 4 layers110 × 120 mm

DUT Interface board v0.2
krishchan007/DUT_Interface_board_v0.2
v0.2 of DUT interface board with significant changes in layout, architecture etc.
271 parts1 - 4 layers99.5 × 91 mm

Questions
How big is the EMG hand sensor PCB?
It measures 73.9 × 41.5 mm and has 4 copper layers, 1.61 mm thick.
What parts does the EMG hand sensor use?
52 parts, built around the STM32F103C8T6, MIC5504-3.3YM5, USBLC6-2SC6 and 3314G-1-101E. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the EMG hand sensor KiCad files?
From the ajama0609/emg_hand_manipulation repository on GitHub, at the commit this page was made from: the board is EMG_hand_sensor/EMG_hand_sensor.kicad_pcb and its schematic EMG_hand_sensor/EMG_hand_sensor.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the EMG hand sensor design in my own project?
Its repository states no licence, so its author keeps all rights: ask ajama0609 before reusing the design.