
Iconograph pcb
A hanging (vertical) plotter. Draws on a surface with implements such as pens, markers, etc. Uses a carriage suspended from two points.
- Size
- 132.2 × 72.2 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 45
- Nets
- 57
- Pads
- 223
- Tracks, vias
- 481, 42
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 8 Dec 2020
- Updated
- 8 Mar 2021
Overview
Iconograph pcb is an open-source printed circuit board by ademuri, from the ademuri/iconograph-cnc repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 132.2 × 72.2 mm with 45 parts on 57 nets, routed with 481 tracks and 42 vias.
It is built around the ULN2003. Its parts include 14 connectors, 7 capacitors, 7 switches, 6 resistors and 2 ICs. It belongs with the ESP32 boards of this library.
Main components
1README
README.mdA hanging (vertical) plotter. Draws on a surface with implements such as pens, markers, etc. Uses a carriage suspended from two points.
Work in progress.
Parts
45| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 100uF | Capacitor_THT:CP_Radial_D8.0mm_P3.50mm | C1, C2, C3, C4, C7 |
| 5 | Conn_01x02 | homebrew:Wurth_ScrewTerminal_1x02_P5.00mm_691137710002 | J1, J4, J6, J8, J9 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 4 | SW_SPST | snapeda:SW_1825910-6-4 | SW4, SW5, SW6, SW7 |
| 3 | Conn_01x03 | homebrew:Wurth_ScrewTerminal_1x03_P5.00mm_691137710003 | J2, J5, J14 |
| 3 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J11, J12, J13 |
| 3 | Pololu_Breakout_DRV8825 | Module:Pololu_Breakout-16_15.2x20.3mm | A1, A2, A3 |
| 3 | SW_DIP_x03 | Button_Switch_THT:SW_DIP_SPSTx03_Slide_9.78x9.8mm_W7.62mm_P2.54mm | SW1, SW2, SW3 |
| 2 | 0.1uF | Capacitor_THT:C_Disc_D5.1mm_W3.2mm_P5.00mm | C5, C6 |
| 2 | 22k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R3 |
| 1 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R6 |
| 1 | 105162-0001 | snapeda:105162-0001 | J10 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2 |
| 1 | 47k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R4 |
| 1 | 68k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R5 |
| 1 | Anderson_two_redblack_src | homebrew:Anderson_1336G1_right_angle_bottom_two | J3 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J7 |
| 1 | D_TVS | Diode_THT:D_DO-15_P10.16mm_Horizontal | D1 |
| 1 | OSHW_LOGO_4mm | homebrew:OSHW_LOGO_4mm | G*** |
| 1 | ULN2003 | Package_DIP:DIP-16_W7.62mm | U2 |
| 1 | mini_esp32 | snapeda:ESP32_mini | U1 |
Similar boards
- 4 layers99.6 × 76.2 mm

- 2 layers31 × 64 mm

Power driver
jmfriedt/SDR-GB-SAR
Opensource, openhardware implementation of a Software Defined Radio (SDR) Ground Based Synthetic-Aperture RADAR (GB-SAR)
6 parts70 - 2 layers160 × 100 mm

MPCNC Nano Estlcam Shield
tnn85/MPCNC-Nano-Estlcam-Shield
Ein CNC Shield für die MPCNC in Verwendung mit Estlcam
96 parts70 - 2 layers42.5 × 43.2 mm

ElectronicFocuser
jlecomte/ascom-oag-focuser
Open Source ASCOM-Compatible OAG Focuser For Astrophotography
4 parts55MIT - 4 layers100 × 49.8 mm

- 2 layers134 × 91 mm

- 2 layers75 × 60 mm

DUTler V2
TheYoctoJester/dutler
A bench butler for your Device Under Test: turns a Raspberry Pi Pico into a USB-serial console bridge with power-relay and MOSFET strap/reset control for embedded-Linux bring-up and hardware-in-the-loop.
54 parts23Apache-2.0 - 4 layers76 × 82.5 mm

Nucleo64 CNC
terjeio/CNC_Breakout_Nucleo64
CNC breakout for STM324F411 and ST32F446 development boards
120 parts22
Questions
How big is the Iconograph pcb PCB?
It measures 132.2 × 72.2 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Iconograph pcb use?
45 parts, built around the ULN2003. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Iconograph pcb KiCad files?
From the ademuri/iconograph-cnc repository on GitHub, at the commit this page was made from: the board is iconograph-pcb/iconograph-pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Iconograph pcb design in my own project?
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).