2 layers114.3 × 25.4 mm
Ir transmitter
adeboni/electronics
This repository stores code for various electronics projects I've made
92 parts
2 layers100 × 100 mm
Ir receiver
adeboni/electronicsThis repository stores code for various electronics projects I've made
- Size
- 100 × 100 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 89
- Nets
- 100
- Pads
- 369
- Tracks, vias
- 577, 37
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 26 Jun 2019
- Updated
- 19 Nov 2025
Overview
Ir receiver is an open-source printed circuit board by adeboni, from the adeboni/electronics repository on GitHub. It is a 2-layer board of 100 × 100 mm with 89 parts on 100 nets, routed with 577 tracks and 37 vias.
It is built around the RP2040, 74LVC1G34Z and RPM3.3-6.0, with the W25Q128JVSIQ, PCM5100APW and ULN2003 among its other parts. Its parts include 34 capacitors, 14 resistors, 10 connectors, 8 ICs and 7 diodes. It belongs with the RP2040 boards of this library.
Main components
8
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
74LVC1G34Z
SOT-553-5-40℃~+125℃ 1 1 1.65V~5.5V 1.6ns@5V,50pF 10uA 32mA 32mA 74LVC Power-off isolation Push-pull Unidirectional SOT-553-5 Buffers, Drivers, Receivers, Transceivers ROHSDiodes IncorporatedBuffers, Drivers, Receivers, Transceivers
RPM3.3-6.0
BLGA-25Isolated Power ModulesRECOM Power
W25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
PCM5100APW
TSSOP-20-40℃~+130℃ 1.8V~3.3V 2 32 384kHz 50MHz Audio Decoder I2S TSSOP-20 ADCs/DACs - Special Purpose ROHSTexas InstrumentsADCs/DACs - Special Purpose
ULN2003
SOP-161.1V@250uA,100mA 25pF 2V 30V 500mA 50uA 50uA Seven channels SOP-16 Darlington Transistor Arrays ROHSBLDarlington Transistor Arrays
SS34
SMA(DO-214AC)-55℃~+125℃ 3A 40V 500uA@40V 550mV@3A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
G5Q-1A
Miniature Power RelayOmronUncategorised
README
README.mdThis repository stores code for various electronics projects I've made
- Wasp Cannon: A wifi-enabled water cannon for shooting water at wasps on my balcony
- CV Glove: A glove with flex sensors on fingers that output control voltages for eurorack modules
- Critter Coat: A coat with fluttering butterflies on it
- AQI Monitor: Simple air quality monitor using a Honeywell HPM sensors
- Atari Controller: Custom Atari 2600 controller with an analog joystick
- Camera Remote: Wireless camera shutter control
- Gas Sensor: A generic MQ gas sensor board with LED indicators
- PS2 Drone Controller: Lets you control quadcopters with a Bluetooth PS2 controller
- WH24 Rachio Adapter: A 915 MHz radio that can receive and parse packets from an Ambient Weather Station and control the rain sensor input on a Rachio irrigation controller
- Scrubotron: A tape head amplifier for use with tape head wands
- Mega Trackball: Adapter PCBs for a bowling-ball sized trackball mouse
- Reverb Pedal: Custom reverb guitar pedal based on a PT2399
- Looper Pedal: Custom looper guitar pedal based on an ISD1000 series voice recorder
Parts
89| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 100n | Capacitor_SMD:C_0603_1608Metric | C4, C5, C6, C7, C8, C9, C12, C13, C14, C38, C42, C45, C46 |
| 8 | 10u | Capacitor_SMD:C_0603_1608Metric | C1, C3, C37, C39, C41, C47, C48, C52 |
| 5 | SS34 | Diode_SMD:D_SMA | D4, D5, D6, D7, D8 |
| 4 | 1u | Capacitor_SMD:C_0603_1608Metric | C10, C11, C40, C44 |
| 4 | G5Q-1A | Relay_THT:Relay_SPST_Omron-G5Q-1A | K1, K2, K3, K4 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1, H2, H3, H4 |
| 4 | Screw_Terminal_01x02 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-2-5.0-H_1x02_P5.00mm_Horizontal | J6, J7, J8, J9 |
| 3 | 1k | Resistor_SMD:R_0603_1608Metric | R17, R22, R23 |
| 3 | 4.7k | Resistor_SMD:R_0603_1608Metric | R5, R7, R8 |
| 2 | 2.2n | Capacitor_SMD:C_0603_1608Metric | C50, C51 |
| 2 | 2.2u | Capacitor_SMD:C_0603_1608Metric | C43, C49 |
| 2 | 27 | Resistor_SMD:R_0603_1608Metric | R3, R6 |
| 2 | 27p | Capacitor_SMD:C_0603_1608Metric | C23, C27 |
| 2 | 470 | Resistor_SMD:R_0603_1608Metric | R34, R42 |
| 2 | 470u 16V | Capacitor_SMD:CP_Elec_8x10 | C15, C16 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | BLM31SN500SN1L | Inductor_SMD:L_1206_3216Metric | FB1, FB2 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D2, D3 |
| 2 | SW_Push | Button_Switch_SMD:SW_SPST_TL3342 | SW1, SW2 |
| 1 | 0472192001 | Connector_Card:microSD_HC_Molex_47219-2001 | J1 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | 1000 | Resistor_SMD:R_0603_1608Metric | R9 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 22u | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | 74LVC1G34 | Package_TO_SOT_SMD:SOT-23-5 | U7 |
| 1 | AP3602 | Package_TO_SOT_SMD:SOT-23-6 | U6 |
| 1 | AudioJack3 | Connector_Audio:Jack_3.5mm_CUI_SJ-3523-SMT_Horizontal | J2 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_Horizontal | J3 |
| 1 | Conn_01x03 | Connector_JST:JST_XH_S3B-XH-A_1x03_P2.50mm_Horizontal | J4 |
| 1 | Conn_02x06_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x06_P2.54mm_Vertical | J10 |
| 1 | FerriteBead | Inductor_SMD:L_0603_1608Metric | FB3 |
| 1 | LOGO | footprints:blast1 | G*** |
| 1 | PCM5100A | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U5 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U3 |
| 1 | RPM3.3-6.0 | Converter_DCDC:Converter_DCDC_RECOM_RPMx.x-x.0 | U1 |
| 1 | SW_DIP_x06 | Button_Switch_THT:SW_DIP_SPSTx06_Slide_6.7x16.8mm_W7.62mm_P2.54mm_LowProfile | SW3 |
| 1 | TSOP58038 | OptoDevice:Vishay_MINICAST-3Pin | U2 |
| 1 | ULN2003 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U8 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_Palconn_UTC16-G | J5 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U4 |
Questions
How big is the Ir receiver PCB?
It measures 100 × 100 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Ir receiver use?
89 parts, built around the RP2040, 74LVC1G34Z, RPM3.3-6.0 and W25Q128JVSIQ. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Ir receiver KiCad files?
From the adeboni/electronics repository on GitHub, at the commit this page was made from: the board is halloween_2025/hardware/ir_receiver/ir_receiver.kicad_pcb and its schematic alien_screamer/alien_screamer.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Ir receiver design in my own project?
Its repository states no licence, so its author keeps all rights: ask adeboni before reusing the design.
More from adeboni/electronics
12- 2 layers100 × 62 mm
Looper
adeboni/electronics
This repository stores code for various electronics projects I've made
63 parts - 2 layers50 × 40 mm
Alien screamer
adeboni/electronics
This repository stores code for various electronics projects I've made
55 parts - 2 layers100 × 42 mm
Delay reverb
adeboni/electronics
This repository stores code for various electronics projects I've made
46 parts - 2 layers85 × 45 mm
Drone tranceiver
adeboni/electronics
This repository stores code for various electronics projects I've made
44 parts - 2 layers
Tape jar
adeboni/electronics
This repository stores code for various electronics projects I've made
28 parts - 2 layers23.1 × 51 mm
Aw rachio adapter
adeboni/electronics
This repository stores code for various electronics projects I've made
20 parts - 2 layers52 × 52 mm
Fiat light relay
adeboni/electronics
This repository stores code for various electronics projects I've made
11 parts - 2 layers60 × 60 mm
Encoder controller
adeboni/electronics
This repository stores code for various electronics projects I've made
10 parts - 2 layers58 × 20 mm
Drum trigger adapter
adeboni/electronics
This repository stores code for various electronics projects I've made
7 parts - 2 layers30.8 × 12.2 mm
Dc dc jack converter
adeboni/electronics
This repository stores code for various electronics projects I've made
5 parts - 2 layers34 × 22.5 mm
Tape jar fp
adeboni/electronics
This repository stores code for various electronics projects I've made
4 parts
Similar boards
- 4 layers87.9 × 95.8 mm
Fosdem dual capture
FOSDEM/video
No longer being updated, please see the README for pointers.
215 parts114 - 2 layers86 × 54 mm
- 2 layers70.8 × 108 mm
- 4 layers252 × 41.5 mm
- 4 layers91.2 × 100 mm
- 2 layers77.5 × 55.6 mm
Most reader
Oleg-mk/JLR-MOST-Reader
Listen-only MOST25 adapter for JLR: the factory stereo out over TOSLINK, the car's own volume controls applied digitally with no quality loss
62 parts1CERN-OHL-S-2.0 - 2 layers123.6 × 78.9 mm
Most listener
Oleg-mk/MOST25-to-AUDIO
Passive MOST25 listener: Tang Nano 20K FPGA, ESP32 host, stereo I2S out with the head unit's volume, balance and tone
172 parts1CERN-OHL-S-2.0 - 4 layers133 × 89.5 mm
ESP32-DevKitC3-Simple Thermostat PCB
jrtaylor71/ESP32-DevKitC3-Simple-Thermostat-PCB
ESP32-DevKitC3 Simple Thermostat with PCB
61 parts2