
Mouse Design
MURERWADANIEL1/Mouse_Design
This Project is for the design of a mouse hardware system.

Project files for custom "kinematic" dress that uses servos to move parts of it in a wavy motion.
Stm32 servo controller is an open-source printed circuit board by ZephyrCloudNine, from the ZephyrCloudNine/kinematic_outfits repository on GitHub. It is a 4-layer board of 74.9 × 57.2 mm with 90 parts on 88 nets, routed with 491 tracks and 134 vias.
It is built around the MT3608B, AO8810 and DW01, with the IP2312U, LP5907MFX-3.3/NOPB(MS) and TXS0108EPW among its other parts. Its parts include 29 resistors, 22 capacitors, 12 connectors, 8 ICs and 5 diodes. It belongs with the robots and motor control boards and the STM32 boards of this library.
Project files for custom "kinematic" dress that uses servos to move parts of it in a wavy motion. Firmware uses an ESP32-C3 Devkit module. Servos used - SG90 along with PCA9685 servo driver to extend servo drive functionality. Mechanical design done on Fusion 360.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C5, C6, C7, C9, C10, C11, C18, C21, C22 |
| 8 | 10K | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R8, R9, R20, R28 |
| 5 | 100R | Resistor_SMD:R_0603_1608Metric | R12, R13, R19, R21, R23 |
| 4 | 1uF | Capacitor_SMD:C_0603_1608Metric | C2, C8, C14, C15 |
| 4 | 5.1K | Resistor_SMD:R_0603_1608Metric | R5, R10, R14, R15 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2, H3, H4 |
| 3 | 22uF | Capacitor_SMD:C_0805_2012Metric | C17, C19, C20 |
| 3 | TestPoint | TestPoint:TestPoint_Pad_D1.0mm | TP1, TP2, TP3 |
| 2 | 1K | Resistor_SMD:R_0603_1608Metric | R25, R26 |
| 2 | 20pF | Capacitor_SMD:C_0603_1608Metric | C3, C4 |
| 2 | 22R | Resistor_SMD:R_0603_1608Metric | R6, R7 |
| 2 | 22uF | Capacitor_SMD:C_1206_3216Metric | C12, C13 |
| 2 | DNP | Resistor_SMD:R_0603_1608Metric | R16, R29 |
| 2 | LED_GREEN | LED_SMD:LED_0603_1608Metric | D2, D5 |
| 2 | LED_ORANGE | LED_SMD:LED_0603_1608Metric | D1, D4 |
| 1 | 0.5R | Resistor_SMD:R_0805_2012Metric | R27 |
| 1 | 1.5K | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C16 |
| 1 | 110K | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | 15K | Resistor_SMD:R_0603_1608Metric | R18 |
| 1 | 2.2uH | Inductor_SMD:L_Sunlord_MWSA0503S | L2 |
| 1 | 51K | Resistor_SMD:R_0603_1608Metric | R22 |
| 1 | 6.8uH | Inductor_SMD:L_Sunlord_MWSA0503S | L1 |
| 1 | 8MHz | Crystal:Crystal_HC49-4H_Vertical | Y1 |
| 1 | AO3415A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | AO8810 | Package_SO:TSSOP-8_4.4x3mm_P0.65mm | U7 |
| 1 | BAT IN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | BTN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | DEBUG | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J1 |
| 1 | DNP | Resistor_SMD:R_0805_2012Metric | R24 |
| 1 | DW01 | Package_TO_SOT_SMD:SOT-23-6 | U6 |
| 1 | FerriteBead | Inductor_SMD:L_0805_2012Metric | FB1 |
| 1 | IP2312 | Package_SO:HSOP-8-1EP_3.9x4.9mm_P1.27mm_EP2.3x2.3mm | U5 |
| 1 | LP5907MFX-3.3/NOPB | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | MT3608B | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | Polyfuse | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | SERVO1 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J5 |
| 1 | SERVO2 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J8 |
| 1 | SERVO3 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J11 |
| 1 | SERVO4 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J6 |
| 1 | SERVO5 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J9 |
| 1 | SERVO6 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J12 |
| 1 | SERVO7 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J7 |
| 1 | SERVO8 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J10 |
| 1 | SJ2_open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP3 |
| 1 | SS54 | Diode_SMD:D_SMB | D3 |
| 1 | STM32F103C8Tx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1 |
| 1 | TXS0108EPW | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U8 |
| 1 | USB4105GFA120 | footprints:GCT_USB4105GFA120 | J3 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |

MURERWADANIEL1/Mouse_Design
This Project is for the design of a mouse hardware system.



RobieElliz/esp32InductanceMeterV2
Portable ESP32 Inductance Meter: A low-cost, high-precision tool with dual 100nF/5µF refs, a TLV3202 comparator, fast USB-C (IP2312) charging, and a 2.4-inch OLED display for real-time readings.

Jan-IngenHousz-Institute/ambyte-battery-charger
KiCad designs for multi-channel IP2312 Li-ion battery chargers

Jzn-wbr/Starter
Un système de réveil connecté qui combine une station audio, un bracelet de mouvement et une application mobile pour transformer le réveil en un vrai départ de journée.


ndoo/ikoka-nano-meshtastic-device
A Meshtastic device based on the Seeed Studio XIAO nRF52840 and EBYTE E22-XXXMXXS series LoRa modules. Pinout matches the Meshtastic xiaoble variant.
It measures 74.9 × 57.2 mm and has 4 copper layers, 1.6 mm thick.
90 parts, built around the MT3608B, AO8810, DW01 and IP2312U. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the ZephyrCloudNine/kinematic_outfits repository on GitHub, at the commit this page was made from: the board is hardware/stm32_servo_controller/stm32_servo_controller.kicad_pcb and its schematic hardware/stm32_servo_controller/battery.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask ZephyrCloudNine before reusing the design.