

Creative controller
Grok Bot account migration home (secrets encrypted)
- Size
- 87.9 × 87.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 59
- Nets
- 54
- Pads
- 249
- Tracks, vias
- 623, 233
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 8 Oct 2026
- Updated
- 27 Oct 2026
Overview
Creative controller is an open-source printed circuit board by ZMGID, from the ZMGID/grokbot-home repository on GitHub. It is a 2-layer board of 87.9 × 87.5 mm with 59 parts on 54 nets, routed with 623 tracks and 233 vias.
It is built around the ESP32-S3-WROOM-1-N16R8, AP2112K-3.3TRG1 and MCP73831T-2ACI/OT-HXY, with the SN74LV1T34DBVR-TP, USBLC6-2SC6 and AO3401A among its other parts. Its parts include 16 resistors, 15 capacitors, 12 switches, 5 ICs and 2 diodes. It belongs with the ESP32 boards of this library.
Main components
10ESP32-S3-WROOM-1-N16R8
SMD,25.5x18mm-103.5dBm -40℃~+65℃ 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA ESP32-S3R8 On-board PCB Antenna UART、SPI、I2C、GPIO、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesAP2112K-3.3TRG1
SOT-25-5-40℃~+85℃@(Ta) 1 250mV@(600mA) 3.3V 50uVrms 55uA 600mA 65dB@(1kHz) 6V Fixed Over Current Protection、Thermal Shutdown、Enable control Positive SOT-25-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMCP73831T-2ACI/OT-HXY
SOT-23-5LBattery ManagementHXY MOSFETSN74LV1T34DBVR-TP
SOT-23-5-40℃~+125℃ 1 1 1.6V~5.5V CMOS CMOS Power-off protection Unidirectional SOT-23-5 Translators, Level Shifters ROHSTECH PUBLICTranslators, Level ShiftersUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)AO3401A
SOT-231 P-Channel 14nC@10V 30V 47mΩ@10V、60mΩ@4.5V、85mΩ@2.5V 4A 55pF 645pF 80pF 900mV SOT-23 MOSFETs ROHSAlpha & Omega SemiconductorMOSFETsB5819W
SOD-123-55℃~+125℃ 1.5A 1mA@40V 25A 40V 600mV@1A Standalone SOD-123 Schottky Diodes ROHSMDDSchottky DiodesPCM12SMTR
SMD-20℃~+85℃ 6V PC Pin Rectangular Columnar SPDT Surface Mount,Vertical SMD Slide Switches ROHSC&KSlide SwitchesTYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB ConnectorsWS2812B-B/T
SMD5050-4P-40℃~+65℃ 0.6mA 1.57mm 120us 200mcd~300mcd 2kHz 3.7V~5.3V 300mcd~500mcd 300ns 471nm 471nm 5.4mm 520nm 520nm 5mm 600mcd~1000mcd 621nm 621nm 800Kbit/s Built-in power-on reset circuit、Built-in power-on reset circuit、Built-in one-way transmission function SMD5050-4P RGB LEDs(Built-in IC) ROHSWorldsemiRGB LEDs(Built-In IC)
README
README.mdgrokbot-home
我的 Grok Bot「家」:换到新的 Grok Bot 账号时,让新号上的 bot 按这个仓库把自己和其他所有 bot 一起配好,做到基本无缝切换。
怎么用
仓库是公开的(2026-10-08 起),新号上的 bot 不用登录 GitHub 就能匿名克隆、读 BOOTSTRAP.md。Composio API key 只以加密形式放在 secrets/*.enc,解密口令只有我知道(应用连接只走 composio-pg,不装官方 GitHub/Origin 等连接器)。
在新号上打开任意一个 Grok Bot(一般是默认的主 bot),对它说:
按这个仓库配置自己:https://github.com/ZMGID/grokbot-home它会读 BOOTSTRAP.md,然后依次:
- (Step 0)匿名克隆本仓库 → 用密码框(secret-request)向我要口令
GROKBOT_HOME_PASSPHRASE→ 解密secrets/COMPOSIO_API_KEY.enc到~/.composio_pg_key(连不上就换.box-current.enc)→ 从connectors/composio-pg/装好并添加 composio-pg; - (Step 1)用 Composio 里 GitHub(ZMGID)的 token 登录
gh——只有往仓库推送(写回、每日同步)才需要; - 跑
setup.sh装好工具环境(KiCad、PlatformIO、cadquery、Composio SDK 等); - 确认
composio-pg已接通;pstack 插件可选(原为 dr eggbot 安装);导入skills/里的技能(若有); - 按
bots/grok-bot/设置自己为 小萌(主 bot;原名 Grok Bot)并读CONTEXT.md; - 用 CreateAgent 把
bots/下其他每个 bot(小枳、仓库管家、代码工程师、搭建运维、事务秘书、硬件工程师……,以bots/index.json为准)重新建出来,并重建它们的定时任务; - 自检,最后把新学到的东西写回仓库。
我需要亲自做的只有:在密码框里填一次仓库口令(解密失败时才要 Composio key 本身;gh 设备码只在推送权限拿不到时备用)。
目录
| 路径 | 内容 |
|---|---|
BOOTSTRAP.md | 写给新 bot 的开机步骤(英文为主,附中文) |
CONTEXT.md | 关于我的共享记忆:习惯、账号、项目进度、换号决定 |
bots/<名字>/ | 每个 bot 一个文件夹:profile.md(设定)、CONTEXT.md(它自己的记忆)、routines.md(定时任务) |
connectors/ | 连接器清单 + composio-pg 启动脚本(不含密钥) |
skills/ | 用户自建技能(目前有 tiktok:TikTok巴西站竞品调研) |
setup.sh | 工具环境安装脚本(可重复运行) |
scripts/ | 每日同步任务说明和脚本、密钥扫描 secret-scan.sh、加解密 secret-crypt.py |
secrets/ | 只放加密后的密钥(*.enc),见 secrets/README.md |
projects/ | 项目文件(仿 TourBox 创作控制器) |
规矩
- 仓库是公开的,明文密钥永远不进仓库。唯一例外是
secrets/*.enc:用scripts/secret-crypt.py加密后的 Composio key。口令只通过 bot 的密码框(secret prompt)给,绝不写进仓库或聊天。推送前必须bash scripts/secret-scan.sh通过。 - 每个号用完,新记住的东西写回对应的
CONTEXT.md再推送。仓库管家每天凌晨 3:14(北京时间)自动同步一次。 - 仓库公开后,里面的共享记忆(
CONTEXT.md、bots/*/CONTEXT.md、bots/*/raw/memory/)任何人都能看到;不要再写进不想公开的内容。不做 export-bot-template 分享模板。
Parts
59| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 10k | Resistor_SMD:R_0402_1005Metric | R1, R2, R13, R14, R15, R16 |
| 5 | 10uF | Capacitor_SMD:C_0603_1608Metric | C1, C4, C5, C6, C7 |
| 4 | 100nF | Capacitor_SMD:C_0402_1005Metric | C2, C8, C9, C10 |
| 4 | 10nF | Capacitor_SMD:C_0402_1005Metric | C11, C12, C13, C14 |
| 4 | MountingHole_2.2mm_M2 | MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 3 | 100k | Resistor_SMD:R_0402_1005Metric | R5, R8, R9 |
| 2 | 22k | Resistor_SMD:R_0402_1005Metric | R10, R11 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | KEY_TOP | Button_Switch_SMD:SW_SPST_PTS645 | SW1, SW2 |
| 1 | 15k | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 1uF | Capacitor_SMD:C_0402_1005Metric | C3 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C15 |
| 1 | 3.3k | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 39k | Resistor_SMD:R_0402_1005Metric | R12 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | AP2112K-3.3TRG1 | Package_TO_SOT_SMD:SOT-23-5 | U4 |
| 1 | B5819W | Diode_SMD:D_SOD-123 | D1 |
| 1 | BOOT | Button_Switch_SMD:SW_SPST_TL3342 | SW11 |
| 1 | EC11E w/ switch 20mm D-shaft | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | ENC1 |
| 1 | ESP32-S3-WROOM-1-N16R8 | RF_Module:ESP32-S3-WROOM-1 | U1 |
| 1 | KEY_BR | Button_Switch_SMD:SW_SPST_PTS645 | SW5 |
| 1 | KEY_SIDE | Button_Switch_SMD:SW_SPST_PTS645 | SW6 |
| 1 | KEY_TALL1 | Button_Switch_SMD:SW_SPST_PTS645 | SW7 |
| 1 | KEY_TALL2 | Button_Switch_SMD:SW_SPST_PTS645 | SW8 |
| 1 | KEY_TR1 | Button_Switch_SMD:SW_SPST_PTS645 | SW3 |
| 1 | KEY_TR2 | Button_Switch_SMD:SW_SPST_PTS645 | SW4 |
| 1 | KEY_WHEEL | Button_Switch_SMD:SW_SPST_PTS645 | SW9 |
| 1 | LiPo 3.7V | Connector_JST:JST_PH_S2B-PH-SM4-TB_1x02-1MP_P2.00mm_Horizontal | J2 |
| 1 | MCP73831T-2ACI/OT | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | Mouse wheel encoder 11mm (Kailh/TTC) | CreativeDial:MouseEncoder_11mm_3pin | ENC2 |
| 1 | PCM12SMTR | Button_Switch_SMD:SW_SPDT_PCM12 | SW12 |
| 1 | RESET | Button_Switch_SMD:SW_SPST_TL3342 | SW10 |
| 1 | SN74LV1T34DBVR | Package_TO_SOT_SMD:SOT-23-5 | U5 |
| 1 | TYPE-C-31-M-12 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | WS2812B-B | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D2 |
Similar boards
- 2 layers64 × 46 mm

- 4 layers54 × 120 mm

Kartonaut
Jan-Philipp-Munsch/kartonaut
TVC model rocket (after BPS.space Scout F): Teensy 4.1 flight firmware, mainboard spec, project log
174 partsMIT - 4 layers68 × 46 mm

Utter
IFAKA/utter
Utter: covert silent-speech text input from surface EMG (open-source ALS voice)
107 parts - 2 layers90 × 55 mm

S3.1-before repack
puji4810/coffe-scale
USB-C J5 ──► U8 ESD ──► R19/R20 22R ──► U4 IO19/IO20 (native USB-Serial/JTAG) │VBUS ├─► U5 TP4057 充电 ──► J6 1S Li-ion └─► D1/Q1 负载切换 ──► VSYS ──► U6 XC6220 3V3 1A ──► VCC3V3 ──► U4/外设 └──► U7 HT7533 ──► VDDADC ──► U1/U3…
96 partsApache-2.0 - 2 layers85.6 × 54 mm

NeuralCard
Brillar0101/NeuralCard
A credit-card-sized PCB that runs a neural network: ESP32-S3, 6-axis IMU, and 24 LEDs wired as the network itself. Draw a digit in the air and watch the activations light up
72 partsCERN-OHL-P-2.0 - 2 layers26 × 38 mm

- 2 layers52 × 24 mm

Bmm sensor
donaldbell/productspeedrun
Let's see how quickly we can get a product idea off the ground.
32 parts - 4 layers58 × 70 mm

Probelab
enkhbold470/kicad-projects
Five KiCad 10 boards (4- and 6-layer): ESP32-S3 industrial gateway, USB-C PD bench supply, RP2040 logic analyzer, FOC motor controller, iCE40 FPGA board.
88 partsCERN-OHL-S-2.0
Questions
How big is the Creative controller PCB?
It measures 87.9 × 87.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Creative controller use?
59 parts, built around the ESP32-S3-WROOM-1-N16R8, AP2112K-3.3TRG1, MCP73831T-2ACI/OT-HXY and SN74LV1T34DBVR-TP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Creative controller KiCad files?
From the ZMGID/grokbot-home repository on GitHub, at the commit this page was made from: the board is projects/creative-controller/pcb/creative-controller.kicad_pcb and its schematic projects/creative-controller/pcb/creative-controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Creative controller design in my own project?
Its repository states no licence, so its author keeps all rights: ask ZMGID before reusing the design.