JellyTracker V0.5.0
- Size
- 35.6 × 40.1 mm
- Copper layers
- 2
- Thickness
- 1 mm
- Parts
- 17
- Nets
- 33
- Pads
- 92
- Tracks, vias
- 183, 49
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 10 Nov 2024
- Updated
- 11 Nov 2024
Overview
JellyTracker V0.5.0 is an open-source printed circuit board by YozoraKurage, from the YozoraKurage/YozoLab-JellyTracker repository on GitHub, published under the MIT licence. It is a 2-layer board of 35.6 × 40.1 mm with 17 parts on 33 nets, routed with 183 tracks and 49 vias.
It is built around the ESP32-C3-WROOM-02-H4, ME6211C33M5G-N and CUS10S30. Its parts include 4 resistors, 3 ICs, 2 capacitors, 2 connectors and 2 switches. It belongs with the ESP32 and RISC-V boards of this library.
Main components
3ESP32-C3-WROOM-02-H4
SMD,20x18mm-105dBm -40℃~+105℃ 2.4GHz 20.5dBm 345mA 3V~3.6V 82mA Bluetooth5.0 ESP32-C3 On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,20x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesME6211C33M5G-N
SOT-23-5-40℃~+150℃ 1 120mV@(100mA) 3.3V 500mA 50uVrms 60uA 6V 70dB@(1kHz) Fixed Over Current Protection、Enable、Short Circuit Protection Positive SOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMICRONEVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsCUS10S30
SOD-323Schottky DiodesDOWO
README
JellyTracker_V0.5.0/KiCAD/readme.mdJellyTracker_V0.5.0 KiCADデータ
[!NOTE] このKiCADデータはKiCAD V7.0で作成されました!
AUXトラッカーとして、LSM_Module-V0.1.0が利用可能です
LSM_ModuleとNi-MH_3.3V-Moduleを利用してNi-MH一本での運用が可能です。
JT_V0.5.0はそのために作成されました
How to Upload to JLCPCB
jlcpcb/production_filesに出力されたBOM、CPL、GERBERデータがあるので、それを使うかKiCADからデータを作成してください
Parts list
| What's it? | Parts Name | LCSC No. |
|---|---|---|
| TypeC Connector | TYPE-C-31-M-12 | C165948 |
| ESP32C3 Module | ESP32-C3-WROOM-02-N4 | C2934560 |
| 3.3V Regulator | ME6211C33M5G-N | C82942 |
| PushButton | SKRKAEE020 | C115357 |
| Caps | CL21B105KBFNNNE | C28323 |
| Resistor | 0603WAF5101T5E | C23186 |
| Resistor | 0603WAF1002T5E | C25804 |
| Diode | CUS10S30,H3F | C146335 |
| PH 2.0 | PH-4P | C50137 |
[!IMPORTANT] 私のPH2.0ケーブルでは、必ず SameSide のケーブルを使う必要があります!
Parts
17| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 1μF | Capacitor_SMD:C_0805_2012Metric | C6, C7 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | MountingHole_2.7mm_M2.5 | MountingHole:MountingHole_2.7mm_M2.5 | M2.5, M2.5 |
| 2 | SW_Push | Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRK | SW1, SW2 |
| 1 | CUS10S30 | Diode_SMD:D_SOD-323 | D2 |
| 1 | ESP32-C3-WROOM-02 | PCM_Espressif:ESP32-C3-WROOM-02 | U5 |
| 1 | JST-PH 2.0 | Connector_JST:JST_PH_S4B-PH-SM4-TB_1x04-1MP_P2.00mm_Horizontal | J7 |
| 1 | LOGO | Yozolab:logo | G*** |
| 1 | ME6211C33M5G-N | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | ~ | Yozolab:BMI160-Module | U2 |
More from YozoraKurage/YozoLab-JellyTracker
2- 2 layers17.8 × 18.3 mm

- 2 layers22.4 × 32.5 mm

Similar boards
- 4 layers98.1 × 94.4 mm

- 4 layers160 × 100 mm

- 2 layers86.5 × 27.5 mm

Comfospot50 full
cornim/comfospot50
The schematic and PCB in this directory are the project-authored controller board design. The board is intended to interface an ESP32-C3 with the existing ComfoSpot panel.
29 parts4GPL-3.0 - 4 layers56 × 28 mm

Bx tacho
dazchi/bx-tacho
Open DIY Beyblade X launcher RPM meter: ESP32-C3 with IR sensors and an OLED, Bluetooth (Battle Pass protocol), and a browser app for shot data and firmware updates. KiCad hardware, ESP-IDF firmware, 3D-printed case.
51 parts3GPL-3.0 - 4 layers62.5 × 96.2 mm

- 2 layers30 × 74.5 mm

Lamp ver2
trsh-mn/smart-home-iot
라즈베리파이 5 + ESP32 기반 스마트홈 IoT: AI 음성대화봇 · 음악 스피커 · 스마트 전등 (펌웨어, 서버, KiCad PCB)
46 parts - 2 layers82 × 40 mm

- 2 layers30.4 × 65 mm

Questions
How big is the JellyTracker V0.5.0 PCB?
It measures 35.6 × 40.1 mm and has 2 copper layers, 1 mm thick.
What parts does the JellyTracker V0.5.0 use?
17 parts, built around the ESP32-C3-WROOM-02-H4, ME6211C33M5G-N and CUS10S30. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the JellyTracker V0.5.0 KiCad files?
From the YozoraKurage/YozoLab-JellyTracker repository on GitHub, at the commit this page was made from: the board is JellyTracker_V0.5.0/KiCAD/JellyTracker_V0.5.0.kicad_pcb and its schematic JellyTracker_V0.5.0/KiCAD/JellyTracker_V0.5.0.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the JellyTracker V0.5.0 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).