Skip to the content
2 layers35 × 83 mmMimigotchi, the printed circuit board in 3D

a little screen-time reminder robot built with pcb design, firmware, and cad

Size
35 × 83 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
30
Pads
66
Tracks, vias
95, 5
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
21 May 2026
Updated
23 Jun 2026

Overview

Mimigotchi is an open-source printed circuit board by WinnyT, from the WinnyT/mimigotchu repository on GitHub, published under the MIT licence. It is a 2-layer board of 35 × 83 mm with 11 parts on 30 nets, routed with 95 tracks and 5 vias.

It is built around the L293D, HS96L03W2C03 and 1207-P6.5MM. Its parts include 3 ICs and 3 switches. It belongs with the ESP32 and RISC-V boards of this library.

Main components

3

README

README.md

Mimigotchu: a non-distractible reminder

This pet will help me reduce my screen time by playing hide-and-seek with me, so I can stay away from my phone! To be specific, they will play sound when I was doing a task for too long and run away so have to stand up and find them. Potential turn into a stress reliever.

image

How to build

  1. 3D print the pet case and wheels
  2. Solder all the component of the PCB on to the PCB
    1. XIAO ESP32-C6 (SMD, center of board)
    2. L293D motor driver (U3)
    3. OLED header pins (U2)
    4. Buttons SW1, SW2, SW3
    5. Buzzer (BUZZER1)
    6. Battery connector (BT1)
    7. Motor connector (M1)
  3. Screw the PCB on to the upper case using the M3 bolt
  4. Put on the rubber band to the wheels
  5. Place the motor on the Right Bottom corner, it should fit the motor holder case
  6. Put the stick in between the hole. THEN put on the wheels. Do the same for both front and back
  7. Snap 2 case todether and connect the pet to your computer with a type-c cable
  8. Download the firmware file and upload it to XIAO ESP32

How to use

There are 3 buttons from LEFT to RIGHT. I'll call them Left - Middle - Right

Left Button: Short press - +1 minute

Middle Button: Short press - +1 second

Right Button: Short press - Start countdown Long press - Switch to pet screen

Left & Middle Button - Reset Timer

Oled screen: Timer mode: showing countdown of the timer MM:SS Pet mode: showing hapiness and age

MIMI will run away when the timer is UP

Why I make this

I found myself addicted to phone, and I have tried many ways to reduce my screen time like set a timer or use a timer lock down. But it never work. The problem I found with setting a timer is I leave it by my side, so it was too easy for me to turn it off and not getting away from my phone. I hope this robot can run away, make me stand up and catch them. Sounds silly but what if it works ?.?

CAD

image

Link to Onshape design.

PCB

Download gebber file

3D view of the PCB

Front

image

Back

image

3D model after assembly the PCB

Front

image

Back

image

Schematic

image

Firmware

You can flash Mimigotchi without installing PlatformIO.

Download latest firmware

Flash instructions (macOS/Windows/Linux)

  1. Install esptool via terminal:

pip install esptool

  1. Connect your Mimigotchi via USB-C
  2. Download bootloader.bin, partitions.bin, and firmware.bin from the release
  3. Run (from the folder containing all three files): esptool.py --port /dev/tty.usbmodem* write_flash

0x0 bootloader.bin

0x8000 partitions.bin

0x10000 firmware.bin On Windows, replace /dev/tty.usbmodem* with COM3

Build from source

If you want to modify the code, open the project in VS Code with PlatformIO installed and press Ctrl+Alt+B to build, then Ctrl+Alt+U to upload.

BOM

Check out mimigotchu_bom.csv or this link.

Easter Egg

If you finished a study session ( 50+ minutes) your pet will be happier !!

Parts

11
QtyValueFootprintReferences
3SW_Pusheasyeda2kicad:SW-TH_4P-L4.5-W4.5-P3.00-LS4.8SW1, SW2, SW3
11207-P6.5MMeasyeda2kicad:BUZ-TH_BD12.5-P6.50-D1.4BUZZER1
1Battery_CellConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalBT1
1HS96L03W2C03easyeda2kicad:OLED-TH_L27.8-W27.2-P2.54_C9900033791U2
1L293Deasyeda2kicad:DIP-16_L20.0-W6.4-P2.54-LS7.6-BLU3
1Motor_DCConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalM1
1XIAO-ESP32-C3-SMDSeeed_Studio_XIAO_Series:XIAO-ESP32-C3-SMDU1

The 9 most common of 11 parts.

Similar boards

  • 2 layers56.8 × 66.2 mmTamagotchi, the printed circuit board in 3D

    Tamagotchi

    TaniWanKenobi/tamagotchi

    A custom PCB-based Tamagotchi virtual pet built with the XIAO-ESP32-C6!

    14 parts5
  • 2 layers50 × 75 mmVideocraft PetPad, the printed circuit board in 3D

    Videocraft PetPad

    Videocraft10/PetPad

    Custom Made Tamagotchi Like Device

    13 parts2MIT
  • 2 layers70.6 × 76 mmTamagotchi, the printed circuit board in 3D

    Tamagotchi

    Er1n-jpg/Psyduck-gotchi

    Tamagotchi project made for fallout

    11 parts1
  • 2 layers64.3 × 76.8 mmTamagotchi, the printed circuit board in 3D

    Tamagotchi

    shelxty/lego-tamagotchi

    Simple tamagotchi with OLED display screen, buzzer, and 3 buttons custom-made in KiCad, with parts assembled in OnShape.

    10 parts1
  • 2 layersReleastic tamagotchi, the printed circuit board in 3D

    Releastic tamagotchi

    alex-technologia/Realistic-tamagochi

    A tamagochi but much more realistically accurate

    10 parts
  • 2 layers74.4 × 97.8 mmTamagotchi, the printed circuit board in 3D

    Tamagotchi

    Ayush09S/Tamagotchi

    A small digital pet as a physical device remake! It features an LDR that can detect light changes, four buttons, and a buzzer. It also has an OLED display!

    16 partsMIT
  • 2 layers95.6 × 69.3 mmFallout pcb, the printed circuit board in 3D

    Fallout pcb

    Er1n-jpg/Fallout-pcb

    12 parts
  • 2 layers74.8 × 74.1 mmTamagotchi, the printed circuit board in 3D

    Tamagotchi

    hiralsinghal/Tamagotchi

    This is a Tamagotchi. It is a small handheld video game in which you have a pet. You can play with it, feed it and more depending on your firmware code.

    10 partsMIT

Questions

How big is the Mimigotchi PCB?

It measures 35 × 83 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Mimigotchi use?

11 parts, built around the L293D, HS96L03W2C03 and 1207-P6.5MM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Mimigotchi KiCad files?

From the WinnyT/mimigotchu repository on GitHub, at the commit this page was made from: the board is assets/pcb/mimigotchi.kicad_pcb and its schematic assets/pcb/mimigotchi.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Mimigotchi design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).