Skip to the content
2 layers80.5 × 40.8 mmSaucey - Copy, the printed circuit board in 3D

This is a design repository for an ESP32 based flight controller I made

Size
80.5 × 40.8 mm
Copper layers
2
Thickness
1.6 mm
Parts
58
Nets
93
Pads
254
Tracks, vias
395, 43
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
22 Oct 2024
Updated
22 Oct 2024

Overview

Saucey - Copy is an open-source printed circuit board by Vulcan758, from the Vulcan758/Saucey-Flight-Controller-PCB repository on GitHub. It is a 2-layer board of 80.5 × 40.8 mm with 58 parts on 93 nets, routed with 395 tracks and 43 vias.

It is built around the ESP32-S3-WROOM-1-N8, CP2102N-A02-GQFN28 and AMS1117-3.3, with the MPU-6050, 1N4148W and SI2306 among its other parts. Its parts include 15 resistors, 13 capacitors, 6 diodes, 6 transistors and 4 ICs. It belongs with the robots and motor control boards and the ESP32 boards of this library.

Main components

7

README

README.md

Saucey-Flight-Controller-PCB

This is a design repository for an ESP32 based flight controller (FC), "Saucey", that I made.

Screenshot from 2024-10-21 20-56-30

Technical Specifications

The FC uses an ESP32 S3 WROOM 1 module as the micrcontroller (MCU). It contains a 3.3 volt linear regulator (AMS1117 was used here) to power the MCU and the inertial measurement unit (IMU). The IMU used here is a MPU6050. This board is to be programmed through USB C. There is no onboard USB-Serial converter chip (such as CH2102) as ESP32 S3 can be programmed directly with its built USB-Serial converter on pins 18 and 19. A status LED is also availiable on board for testing and debugging. The FC board has 4 half bridge SI2306 logic level MOSFETs meant to drive coreless motors via JST connectors. This can however drive/ignite model rocket motors, LEDs and other low voltage output devices.

The goal of this project was to design a smart flight controller board with a credit card size form factor.

PCB Schematic

Screenshot from 2024-10-22 01-19-56

PCB Layout

Screenshot from 2024-10-22 01-10-28

Top Layer

With ground pour

Screenshot from 2024-10-22 01-11-43

Without ground pour

Screenshot from 2024-10-22 01-11-12

Bottom Layer

With ground pour

Screenshot from 2024-10-22 01-11-51

Without ground pour

Screenshot from 2024-10-22 01-11-23

Parts

58
QtyValueFootprintReferences
1010kResistor_SMD:R_0805_2012MetricR2, R6, R7, R9, R10, R11, R12, R13, R14, R15
51uCapacitor_SMD:C_0402_1005MetricC5, C11, C12, C13, C14
41N4148WDiode_SMD:D_SOD-123D2, D3, D4, D5
4SI2306Package_TO_SOT_SMD:SOT-23Q4, Q5, Q6, Q7
30.1uCapacitor_SMD:C_0603_1608MetricC2, C8, C9
3Motor_DCConnector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_HorizontalM2, M3, M4
210uCapacitor_SMD:C_0603_1608MetricC1, C7
22.2kResistor_SMD:R_0805_2012MetricR1, R8
222uCapacitor_SMD:C_1210_3225MetricC3, C4
2LEDLED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolderD1, D6
2S8050Package_TO_SOT_THT:TO-92_InlineQ1, Q2
2SW_PushButton_Switch_SMD:SW_SPST_B3U-1000PSW1, SW2
11kResistor_SMD:R_1206_3216MetricR5
11ufCapacitor_SMD:C_0402_1005MetricC6
122kResistor_SMD:R_1210_3225MetricR3
148kResistor_SMD:R_1206_3216MetricR4
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U2
1CP2102N-A02-GQFN28Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mmU3
1Conn_01x02_SocketConnector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_HorizontalJ1
1ESP32-S3-WROOM-1RF_Module:ESP32-S3-WROOM-1U1
1LOGOlogo:logov1G***
1LOGOlogo:logov1_biggerG***
1MPU-6050Sensor_Motion:InvenSense_QFN-24_4x4mm_P0.5mmU4
1Motor JSTConnector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_HorizontalM5
1USB_C_Plug_USB2.0Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_HorizontalP1

The 54 most common of 58 parts.

More from Vulcan758/Saucey-Flight-Controller-PCB

2
  • 2 layers74.5 × 41.3 mmSaucey, the printed circuit board in 3D

    Saucey

    Vulcan758/Saucey-Flight-Controller-PCB

    This is a design repository for an ESP32 based flight controller I made

    49 parts
  • 2 layers95.5 × 40 mmSaucey - Copy, the printed circuit board in 3D

    Saucey - Copy

    Vulcan758/Saucey-Flight-Controller-PCB

    This is a design repository for an ESP32 based flight controller I made

    48 parts

Similar boards

  • 2 layers80 × 54 mmBis zone, the printed circuit board in 3D

    Bis zone

    tsmiltonAgents/pl60c-dmx-wakeup

    A small ESP32-S3 board that drives the wired DMX512 input of a Neewer PL60C panel light so the light can be ramped up slowly in the morning (sunrise alarm). Rev A, 2026-09-02.

    39 parts
  • 2 layers139.7 × 88.9 mmCharge Controller, the printed circuit board in 3D

    Charge Controller

    jharvey/Charge_Controller

    MPPT hardware which uses FUGU firmware

    163 parts24
  • 2 layers80 × 36.6 mmSerial number, the printed circuit board in 3D

    Serial number

    PurkkaKoodari/ktane-hw

    Fully playable hardware implementation of Keep Talking and Nobody Explodes. Mirror of https://gitlab.com/PurkkaKoodari/ktane-hw

    28 parts2MIT
  • 2 layers55 × 55 mmMATRIX WS2812B, the printed circuit board in 3D

    MATRIX WS2812B

    ctayupanta/PANEL-16X16-WS2812B

    298 parts
  • 2 layers43.3 × 62.9 mmSumo Geral Modular, the printed circuit board in 3D

    Sumo Geral Modular

    project-neon/Dory

    Projeto de robô de sumô da Neon para 500g

    54 parts3MIT
  • 4 layers100 × 80 mmHackathon board v2, the printed circuit board in 3D

    Hackathon board v2

    Brian-Nziza/ESP32-Hackathon-Board

    KiCad 10 project. Board is 100 × 80 mm, four layers, fabricated by JLCPCB.

    75 parts
  • 2 layers65 × 38.2 mmGps tracer, the printed circuit board in 3D

    Gps tracer

    OlegDemk/ESP32_GPS_loger_v1

    GPS logger can log in GPS data every 5 seconds into Micro SD card.

    88 parts

Questions

How big is the Saucey - Copy PCB?

It measures 80.5 × 40.8 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Saucey - Copy use?

58 parts, built around the ESP32-S3-WROOM-1-N8, CP2102N-A02-GQFN28, AMS1117-3.3 and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Saucey - Copy KiCad files?

From the Vulcan758/Saucey-Flight-Controller-PCB repository on GitHub, at the commit this page was made from: the board is v2/saucey - Copy.kicad_pcb and its schematic saucey.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Saucey - Copy design in my own project?

Its repository states no licence, so its author keeps all rights: ask Vulcan758 before reusing the design.