

Zx tsid
MOS SID sound card for ZX Spectrum
- Size
- 83 × 39.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 79
- Nets
- 83
- Pads
- 391
- Tracks, vias
- 1,468, 125
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 15 May 2020
- Updated
- 17 Jun 2026
Overview
Zx tsid is an open-source printed circuit board by UzixLS, from the UzixLS/zx-tsid repository on GitHub, published under the MIT licence. It is a 2-layer board of 83 × 39.5 mm with 79 parts on 83 nets, routed with 1,468 tracks and 125 vias.
It is built around the NE5532DR-MS and AMS1117-3.3. Its parts include 34 resistors, 24 capacitors, 6 ICs, 4 connectors and 1 crystal. It belongs with the retro computing and games boards and the FPGA and CPLD boards of this library.
Main components
2NE5532DR-MS
SOP-8-18V~18V -40℃~+85℃ 100nA 110dB 15MHz 2 200nA 2V~18V 300uV 5V/us 5nV/√Hz@1kHz 6mA SOP-8 Operational Amplifier ROHSMSKSEMIOperational AmplifierAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdZX-TSid
MOS SID sound card for ZX Spectrum edge connector (ZX-BUS).
PCB is compatible with SID 6581 and 8580, but also contains integrated SwinSID emulator.
SID accessible via #xxCF port, where xx - SID's register number.
You may connect your ZX Spectrum audio output to second 3.5mm jack and it will be mixed in sound card output signal.
NOTE: +12V/+9V voltage is strictly required for SID, your ZX Spectrum or clone must provide it on the edge connector.
Changelog & current status
- Rev.A - initial release with SID, AY and Covox. Errata.
- Rev.B - abandoned. Files kept for historical reason.
- Rev.C - removed AY and Covox. Added SwinSID emulator. PCB is vertical oriented now.
- Rev.D - improved signal-noise ratio. Fixed read from SID chip.
TODO:
- Check with 8580 SID chip;
- Further improve signal-noise ratio.
Parts
79| Qty | Value | Footprint | References |
|---|---|---|---|
| 13 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R8, R9, R14, R15, R16, R17, R20, R21, R24, R27, R36, R37 |
| 10 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R2, R6, R11, R12, R13, R25, R26, R28, R34, R35 |
| 8 | 100n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C4, C12, C13, C14, C15, C16, C17 |
| 5 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1, JP2, JP3, JP4, JP5 |
| 4 | 220k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R22, R23, R30, R33 |
| 2 | 100u/16V | Capacitor_Tantalum_SMD:CP_EIA-6032-28_Kemet-C_Pad2.25x2.35mm_HandSolder | C5, C11 |
| 2 | 10u | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C6, C9 |
| 2 | 1n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3, C19 |
| 2 | 2.2u | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C2, C10 |
| 2 | 20k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3, R7 |
| 2 | 22n | Capacitor_THT:C_Rect_L7.0mm_W2.5mm_P5.00mm | C21, C24 |
| 2 | 4.7n | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C8, C23 |
| 2 | 4.7u | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A_Pad1.58x1.35mm_HandSolder | C7, C20 |
| 2 | 470p | Capacitor_THT:C_Rect_L7.0mm_W4.5mm_P5.00mm | C18, C22 |
| 2 | 47k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R31, R32 |
| 2 | 8.2k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R18, R19 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2 |
| 2 | PJ307 | my:PJ307 | J3, J4 |
| 2 | RM063 47k | Potentiometer_THT:Potentiometer_Runtron_RM-063_Horizontal | RV1, RV2 |
| 1 | 330k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R29 |
| 1 | 8580 | Package_DIP:DIP-28_W15.24mm_Socket | U5 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | Conn_02x05_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical_SMD | J1 |
| 1 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP6 |
| 1 | NE5532DR | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | SAA1099 | Package_DIP:DIP-18_W7.62mm_Socket | U2 |
| 1 | XC9572XL-VQ64 | Package_QFP:TQFP-64_10x10mm_P0.5mm | U6 |
| 1 | XO91 | Oscillator:Oscillator_SMD_EuroQuartz_XO91-4Pin_7.0x5.0mm | X1 |
| 1 | YM2149 | Package_DIP:DIP-40_W15.24mm_Socket | U1 |
| 1 | zx_edge | my:ZX_CONN | J2 |
More from UzixLS/zx-tsid
2- 2 layers83 × 39.5 mm

- 2 layers73.8 × 37.3 mm

Similar boards
- 2 layers121 × 75.5 mm

Jlctest
cjheath/jlcbasic
JLC Basic parts library for Kicad fetched and converted from EasyEDA
46 parts5 - 4 layers66.7 × 53.5 mm

Custom keyboard
norbertsawe/custom_synth_controller
An open-source, high-performance synthesizer controller built around the Raspberry Pi RP2040 microcontroller. Designed for low-latency MIDI processing, versatile hardware control surfaces, and custom electronic…
95 parts1 - 2 layers296.5 × 175.3 mm

- 4 layers58 × 77.4 mm

AWG
MatthiasElectronic/AWG_DHO8-900
artificial waveform generator / function generator for DHO800 and DHO900 series (AWG/AFG)
208 parts221CERN-OHL-W-2.0 - 2 layers67.6 × 40.6 mm

Robal
nietaki/robal
Debugging expansion for the LABOR modular prototyping board by Moritz Klein and Erica Shnths
56 parts1CC-BY-SA-4.0 - 4 layers100 × 70 mm

SEM
Serhio4522/SEM_hitachi-
Digitization of a Hitachi scanning electron microscope (SEM) — hardware design, FPGA firmware, and analog frontend schematics.
288 parts1 - 4 layers64 × 115 mm

- 4 layers85.1 × 50.8 mm

Questions
How big is the Zx tsid PCB?
It measures 83 × 39.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Zx tsid use?
79 parts, built around the NE5532DR-MS and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Zx tsid KiCad files?
From the UzixLS/zx-tsid repository on GitHub, at the commit this page was made from: the board is pcb/rev.B/zx-tsid.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Zx tsid design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).

