Skip to the content
2 layers5.3 × 12.3 mmKOGUMA Mk4 Encoder, the printed circuit board in 3D

KOGUMA Mk4 Encoder

Tokoro0917/KOGUMA-Mk4
Size
5.3 × 12.3 mm
Copper layers
2
Thickness
0.6 mm
Parts
3
Nets
14
Pads
25
Tracks, vias
26, 2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
9 Oct 2026
Updated
6 Nov 2026

Overview

KOGUMA Mk4 Encoder is an open-source printed circuit board by Tokoro0917, from the Tokoro0917/KOGUMA-Mk4 repository on GitHub. It is a 2-layer board of 5.3 × 12.3 mm with 3 parts on 14 nets, routed with 26 tracks and 2 vias.

It is built around the MT6835. Its parts include 1 capacitor, 1 IC and 1 connector. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

1

README

hardware/kicad/KOGUMA-Mk4_Encoder/README.md

KOGUMA-Mk4_Encoder(エンコーダの基板)

KiCad 9.0 で開く(KOGUMA-Mk4_Encoder.kicad_pro)。左右で同じ基板を2枚使う。

ファイル中身
KOGUMA-Mk4_Encoder.kicad_sch回路図: MT6835、C1(0.1µF)、J1(メイン基板へのパッド7つ)
KOGUMA-Mk4_Encoder.kicad_pcb基板: 5.3 × 12.3 × 0.6mm、2層。MT6835 はチップの面(F)、C1 は裏の面(B)
KOGUMA-Mk4_Encoder.kicad_symMT6835 の記号(KiCad の標準ライブラリにないので作った。ピンはデータシート Rev.1.3 の表)
KOGUMA-Mk4_Encoder.pretty/ENC_Edge基板の上の辺のパッド。Dwgs.User にメイン基板の上下の面、磁石の軸、マウントのくぼみ、下の辺を描いてある
KOGUMA-Mk4_Encoder.pretty/TSSOP-16_4.4x5mm_P0.65mm_Pad0.35KiCad の TSSOP-16 のパッドの幅を 0.4 → 0.35mm にしたもの(1・8・9・16番と基板の縁を 0.2mm 離すため)

メイン基板の側のフットプリントは ../KOGUMA-Mk4/KOGUMA-Mk4.pretty/ENC_Base_Slot(J5・J6)。番号は J1 と同じ。

置き方(モーターマウント v9)

  • メイン基板(0.6mm、z 13.6〜14.2)の穴(NPTH 1.0 × 5.9mm)に下から通し、上に 1.4mm 出た所を、メイン基板の上で両面からはんだ付けする。机の上で付けてから、メイン基板ごとマウントに載せる
  • 基板は z 3.3〜15.6(下の辺はフレームから 0.3mm 浮く)、x −2.65〜2.65(x 0 が車軸の真上)。チップの面(F)は外(磁石の側)を向き、マウントの面と 0.1mm
  • MT6835 の中心は x 0、z 7.5(上の辺から 8.1mm)。IC と磁石のすき間は 0.5mm
  • チップの面の部品はマウントのくぼみ(z 3.8〜11.3)の中だけ。くぼみより上は線だけ。裏の面(B、内側)は開いているので C1 を置く
  • 左右で同じ基板。右は 180° 回した向きで付ける(メイン基板の J6 を 180° 回して置く)

J1(上の辺から 0.2〜2.0mm)

番号ネット面幅
1+3V3裏(B)2.2mm
2ENC_CAL(CAL_EN)チップの面(F)0.6mm
3ENC_MISOチップの面(F)0.6mm
4ENC_MOSIチップの面(F)0.6mm
5ENC_SCKチップの面(F)0.6mm
6ENC_CSチップの面(F)0.6mm
7GND裏(B)2.2mm

チップの面のパッドのピッチは 1.0mm(すき間 0.4mm)。

回路と配線

  • MT6835 は 180° 回し、SPI と CAL_EN のある辺(1〜8番)を上に向けた。5本はチップの面をまっすぐ上のパッドへ
  • VDD(9)・VSS(12)は IC の下のビアで裏に移り、C1(0.1µF、0402)を通って上の 3.3V・GND のパッドへ
  • TEST(11)・TEST_EN(13)は GND(データシートの図5・6)。U・V・W・A・B・Z・OUT は使わない
  • CAL_EN(4)は中に 250kΩ のプルダウンがあり、ふだんは L。校正のときにメイン基板の PC15 で H にする
  • TVS(データシートの推奨)は場所がないので付けない

確かめたこと(2026-10-29、kicad-cli 9.0.9)

  • ERC: エラー 0(警告は、確かめた環境に KiCad の標準ライブラリが登録されていないことによるものだけ)
  • DRC: エラー 0、つながっていないパッド 0、回路図と基板の食い違い 0。ルールは ToraNeko.Mk3 と同じ(クリアランス 0.2mm、ビア 0.6/0.3mm、穴と穴 0.25mm、縁まで 0.2mm)

まだ決めていないこと

  • 面付け(1枚が小さいので、何枚かつないで注文する。ToraNeko.Mk3 の panel/ を参考に)
  • メイン基板を 0.8mm にするなら、上に出る長さが 1.2mm になる(パッドはそのままで足りる)
  • 直角の出し方(はんだ付けのときの治具)

Parts

3
QtyValueFootprintReferences
1100nCapacitor_SMD:C_0402_1005MetricC1
1MAIN_BOARDKOGUMA-Mk4_Encoder:ENC_EdgeJ1
1MT6835KOGUMA-Mk4_Encoder:TSSOP-16_4.4x5mm_P0.65mm_Pad0.35U1

Similar boards

  • 4 layers35 × 35 mmLemon pepper, the printed circuit board in 3D

    Lemon pepper

    VIPQualityPost/lemon-pepper-stepper

    simplefoc all-in-one 50W hybrid stepper + bldc driver

    87 parts75MIT
  • 2 layers24 × 32 mmMt6835-hoverboard, the printed circuit board in 3D

    Mt6835-hoverboard

    mcells/mt6835-hoverboard-motor

    MT6835 magnetic Encoder Breakout board, eg. for mounting inside Hoverboard motors

    14 parts29
  • 4 layers163 × 83 mmVoxboard, the printed circuit board in 3D

    Voxboard

    shadedvox/arsenal

    A fully custom 6 degree-of-freedom robotic arm, built from the ground up across hardware, firmware, and mechanical design.

    182 parts1Apache-2.0
  • 2 layers42 × 42 mmMT6835-NEMA17, the printed circuit board in 3D

    MT6835-NEMA17

    VIPQualityPost/MT6835-NEMA17

    High resolution magnetic angle sensor which can be mounted to the back of NEMA17 sized stepper motors. Enables use of SPI, ABZ, UVW, and PWM outputs.

    13 parts
  • 2 layers46.4 × 27 mmNon magic encoder r1, the printed circuit board in 3D

    Non magic encoder r1

    VX-wiki/non-magic-encoder

    A non-magic magnetic encoder for Vectrix VX-1 maxi scooter motor controller

    20 parts
  • 2 layers21 × 17 mmEncoder MT6835, the printed circuit board in 3D

    Encoder MT6835

    runger1101001/Magnetic_Encoders

    Small (21x17mm) board for the SC60228 magnetic absolute angle sensor.

    11 parts11
  • 4 layers46 × 48 mmMini qdd, the printed circuit board in 3D

    Mini qdd

    duwogus7650-ctrl/board-design

    OpenRobot SPN-MC(=VESCular6, VESC6 파생) 동등 기능의 QDD용 원형 모터 컨트롤러를 오픈소스 VESC6를 베이스로 신규 설계하는 프로젝트.

    31 parts

Questions

How big is the KOGUMA Mk4 Encoder PCB?

It measures 5.3 × 12.3 mm and has 2 copper layers, 0.6 mm thick.

What parts does the KOGUMA Mk4 Encoder use?

3 parts, built around the MT6835. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the KOGUMA Mk4 Encoder KiCad files?

From the Tokoro0917/KOGUMA-Mk4 repository on GitHub, at the commit this page was made from: the board is hardware/kicad/KOGUMA-Mk4_Encoder/KOGUMA-Mk4_Encoder.kicad_pcb and its schematic hardware/kicad/KOGUMA-Mk4/KOGUMA-Mk4.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the KOGUMA Mk4 Encoder design in my own project?

Its repository states no licence, so its author keeps all rights: ask Tokoro0917 before reusing the design.