
Ultra DB X51 v1
ExploreEmbedded/8051_DevelopmentBoard
Design files and sample code for 8051 development Ultra Boards

A Macropad, that drives like a car?????
Carpet is an open-source printed circuit board by Taran-the-Idiot, from the Taran-the-Idiot/carpet repository on GitHub. It is a 2-layer board of 62 × 67 mm with 16 parts on 32 nets, routed with 129 tracks and 120 vias.
It is built around the L293D. Its parts include 6 diodes, 6 switches and 1 IC. It belongs with the keyboards and input boards of this library.

What if you had a macropad, that drives????
This is your average macropad by day but with the push of a button it turns into a toy car you can drive around on your desk. It has 4 cherry MX switches and 2 EC11 rotary encoders. For the drive motors it uses 2 N20 motors
It runs off a custom made RP2040 dev board and uses kmk firmware.


This board runs on a custom devboard that was built for this use case that required smaller packaging.
The motors used for the drive system are N20 motors and they are powered using the L293D motor controlelr.
For the macropad side of things, this board uses a 2x3 matrix with 4 MX keys and 2 encoders.
In order to preserve size and packaging, a choice was made to avoid using a battery and instead the pad is run off of cable power direct from usb.



CAD Was made in Shapr3d. It is your basic macropad case but also includes 2 wheels that go directly on the motor shafts and are lined with TPU treads for grip.
The 2 holes on the top of the case exist for the purpose of being able to reach the boot and reset buttons on the microcontroller without having to break open the case.
There are 2 fake wheels on the lower section that exist for the purpose of reducing friction between the pad and the desk due to the lower surface area.
STLs for printing can be found at the Production/Prints directory.
A STEP assembly for editing can be found at the CAD directory
This board uses KMK as the driving software for its functionality.
The board has 5 layers in the following format:
On the driving aspect, you can call the following functions in order to allow the pad to drive:
forward() - Move the pad forward
backward() - Move the pad backward
turn_right() - Turn the pad right
turn_left() - Turn the pad left
stop() - Stops both motors
Currently the functions are not tuned to specific degree turns or specific distances.
However that would more than likely depend and differ between builds so I recommend tuning them yourself anyways to get the desired outcomes.
| Item | Count/pack | QTY needed | Packs | Cost(AUD) | Shipping(AUD) | Total(AUD) | Total(USD) | Link | Notes |
|---|---|---|---|---|---|---|---|---|---|
| PCB | 5 | 1 | 1 | 4.27 | 2.1 | 6.37 | 4.54 | JLCpcb.com | |
| Switches | 10 | 4 | 1 | 4.75 | 0 | 4.75 | source | ||
| EC11 encoder | 5 | 2 | 1 | 6.26 | 0 | 6.26 | source | ||
| Taranium-RP2040 | 1 | 1 | 1 | N/a | N/a | N/a | N/a | source | Not Commercially available |
| N20 Motors | 1 | 2 | 2 | 3.27 | 0 | 6.54 | source | ||
| M3X5X4 Heatset Inserts | 50 | 8 | 1 | 3.61 | 0 | 3.61 | source | ||
| L293D | 5 | 1 | 1 | 3.59 | 0 | 3.59 | source | ||
| M3x16mm Screw | 50 | 2 | 1 | 3.22 | 0 | 3.22 | source | ||
| M3x25mm Screw | 50 | 2 | 1 | 4 | 0 | 4 | source | ||
| M3x6mm Screws | 50 | 4 | 1 | 2.55 | 0 | 2.55 | source | ||
| 3D Printed Parts | 13 | N/A | N/A | YOUR PRINTER | Cost depends on filament used. | ||||
| Total | 40.89 | 29.2993206 |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | D_Small | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D1, D2, D3, D4, D5, D6 |
| 4 | SW_Push | Taranium-libs:SW_Cherry_MX_1.00u_PCB | SW3, SW4, SW5, SW6 |
| 2 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M1, M2 |
| 2 | RotaryEncoder_Switch | Rotary_Encoder:RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW1, SW2 |
| 1 | L293D | Package_DIP:DIP-16_W7.62mm | U1 |
| 1 | ~ | Taranium-libs:Taranium_Pico | Pico1 |

ExploreEmbedded/8051_DevelopmentBoard
Design files and sample code for 8051 development Ultra Boards

NikodemBartnik/Small-Projects
All of smaller projects (Arduino, PCBs, electronics, code)

geno543/Redropi_highway
the project aims to detect asteroids and meteor movement using high-quality cameras and radar detection methods using an AI model for accurate analysis, and it classifies bodies be in three categories: non-meteor…


harrislab-brown/DropGen
DropGen uses a fluid reservoir and a piezoelectric buzzer to precisely and repeatably dispense small droplets on demand.



It measures 62 × 67 mm and has 2 copper layers, 1.6 mm thick.
16 parts, built around the L293D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Taran-the-Idiot/carpet repository on GitHub, at the commit this page was made from: the board is PCB/PCB.kicad_pcb and its schematic PCB/PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Taran-the-Idiot before reusing the design.