2 layers68 × 17 mm
2 layers
PCB PD
Taran-the-Idiot/Flippy- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 73
- Nets
- 167
- Pads
- 431
- Tracks, vias
- 7, 0
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 13 Jun 2026
- Updated
- 26 Jun 2026
Overview
PCB PD is an open-source printed circuit board by Taran-the-Idiot, from the Taran-the-Idiot/Flippy repository on GitHub, published under the MIT licence. It is a 2-layer board with 73 parts on 167 nets, routed with 7 tracks and 0 vias.
It is built around the RP2040, SCT2650STER and W25Q16JVSSIQ, with the MCP23017-E/SS, USBLC6-2SC6 and NSR0320MW2 among its other parts. Its parts include 31 capacitors, 17 resistors, 8 connectors, 7 ICs and 3 switches. It belongs with the RP2040 boards of this library.
Main components
7
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
SCT2650STER
ESOP-8-40℃~+150℃ 1 100kHz~1.2MHz 175uA 4.5V~60V 5A 800mV~57V Adjustable Buck Buck Built-in ESOP-8 DC-DC Converters ROHSSCTDC-DC Converters
W25Q16JVSSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 10uA 133MHz 16Mbit 2.7V~3.6V 20 Years 3ms SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASH
MCP23017-E/SS
SSOP-28(5.3x10.2x0.65)-40℃~+125℃ 1.7MHz 1.8V~5.5V 16 1uA 600mV 8 8mA I2C Interrupt Output Reset function、Cascading and address extension SSOP-28 I/O Expanders ROHSMicrochip TechnologyI/O Expanders
USBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
NSR0320MW2
SOD-323-55℃~+125℃ 1 Independent 1A 20V 500mV@900mA 50uA@15V 5A SOD-323 Schottky Diodes ROHSonsemiSchottky DiodesKBPC5010T
--55℃~+150℃@(Tj) 1.1V@25A 1kV 400A 50A 5uA@1000V Single-Phase Rectifier - Bridge Rectifiers ROHSGeneSiC SemiconductorBridge Rectifiers
README
README.mdFlippy
Custom Flip dot
Parts
73| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100nf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C9, C10, C18, C20, C21, C23, C24, C25, C26, C27, C28, C31, C32, C33 |
| 5 | 47uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11, C12, C13, C14, C15 |
| 4 | 4.7uf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C5, C6, C7, C8 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 3 | SW_Push | Taranium-libs:C720477 | SW1, SW2, SW3 |
| 2 | 10k | Resistor_SMD:R_01005_0402Metric | R12, R16 |
| 2 | 10uf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C16, C17 |
| 2 | 15pf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C29, C30 |
| 2 | 1uf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C19, C22 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R9, R10 |
| 2 | 300 | Resistor_SMD:R_01005_0402Metric | R15, R17 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R7, R8 |
| 2 | Conn_01x20_Pin | Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_Vertical | J9, J10 |
| 2 | MCP23017 | Package_DFN_QFN:QFN-28-1EP_6x6mm_P0.65mm_EP4.25x4.25mm | U6, U7 |
| 1 | +12V | Taranium-libs:5P_Screw_Terminal | J6 |
| 1 | +3V3 | Taranium-libs:5P_Screw_Terminal | J7 |
| 1 | 10.2k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R6 |
| 1 | 10k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R13 |
| 1 | 12mHz | Taranium-libs:CRYSTAL-SMD_4P-L3.2-W2.5-BL | Y1 |
| 1 | 1k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R11 |
| 1 | 200k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R3 |
| 1 | 20k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R4 |
| 1 | 300 | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R14 |
| 1 | 309k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R1 |
| 1 | 31.8k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R5 |
| 1 | 4.7nf | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C3 |
| 1 | 47pf | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C4 |
| 1 | 76.8k | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2 |
| 1 | C48192 | Taranium-libs:USB-C-SMD_20P-P0.50-L6.5-W8.9 | D3 |
| 1 | Conn_01x12_Pin | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J11 |
| 1 | Conn_Receptacle_3P_Protected | Taranium-libs:240V Power Outlet | J1 |
| 1 | GND | Taranium-libs:5P_Screw_Terminal | J8 |
| 1 | KBPC5010T | Taranium-libs:DIO-BG-TH_KBPC25 | D1 |
| 1 | MCP1700 | Package_TO_SOT_SMD:SOT-23 | U3 |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U2 |
| 1 | SCT2650STE | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm | U1 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | USB_C_Receptacle_USB2.0_14P | Taranium-libs:USB-C-SMD_20P-P0.50-L6.5-W8.9 | J2 |
| 1 | W25Q16JVSS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U5 |
More from Taran-the-Idiot/Flippy
2- 2 layers
Similar boards
- 4 layers81.2 × 100.2 mm
- 2 layers258.2 × 141.2 mm
- 2 layers86.6 × 77.2 mm
Restore backup 2026-10-15T00-06-46-763
JulCesarCorrea/Basic-EPS
PCB design para a 4 fase da obsat
139 parts - 2 layers39.1 × 26.9 mm
Taranium RP2040
Taran-the-Idiot/Taranium-RP2040
An RP2040 devboard that is made to be compact and have its pins horizontally rather than vertically so it can have better packaging for my projects.
39 partsMIT - 4 layers299 × 127 mm
- 4 layers53 × 42 mm
MioLink
Misaka0x2730/MioLink
ARM JTAG/SWD debugger (BlackMagic port) based on RP2040.
117 parts30GPL-3.0 - 2 layers353.1 × 124.9 mm
- 4 layers110 × 120 mm
DUT Interface board v0.2
krishchan007/DUT_Interface_board_v0.2
v0.2 of DUT interface board with significant changes in layout, architecture etc.
271 parts1
Questions
What parts does the PCB PD use?
73 parts, built around the RP2040, SCT2650STER, W25Q16JVSSIQ and MCP23017-E/SS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the PCB PD KiCad files?
From the Taran-the-Idiot/Flippy repository on GitHub, at the commit this page was made from: the board is PCB-PD/PCB-PD.kicad_pcb and its schematic PCB-Controller/PCB-Controller.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the PCB PD design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).