8 layers34.5 × 31.5 mm
2 layers47.6 × 41.5 mm
OLL.E fpv pcb
Tamim101/flight-controller-PCB- Size
- 47.6 × 41.5 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 130
- Nets
- 126
- Pads
- 480
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 4 Aug 2026
- Updated
- 1 Sep 2026
Overview
OLL.E fpv pcb is an open-source printed circuit board by Tamim101, from the Tamim101/flight-controller-PCB repository on GitHub. It is a 2-layer board of 47.6 × 41.5 mm with 130 parts on 126 nets.
It is built around the UCC27511ADBV, MP2315GJ-Z and BMP280, with the AON7410, ICM-42688-P and USBLC6-2SC6 among its other parts. Its parts include 49 capacitors, 31 resistors, 14 ICs, 8 diodes and 6 connectors. It belongs with the STM32 boards of this library.
Main components
11
UCC27511ADBV
SOT-23-6-40℃~+140℃ 1 1V~1.2V 2.2V~2.4V 4.5V~18V 4A 7ns 8A 8ns IGBT、MOSFET Low Side Under Voltage Protection SOT-23-6 Gate Drivers ROHSTexas InstrumentsGate Drivers
MP2315GJ-Z
TSOT-23-8-40℃~+125℃ 1 180uA 3A 4.5V~24V 500kHz 800mV~22.8V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Frequency synchronization、Hiccup current limiting、Built-in LDO regulator Step-down type Yes TSOT-23-8 DC-DC Converters ROHSMonolithic Power SystemsDC-DC Converters
BMP280
LGA-8(2x2.5)-40℃~+85℃ 0.12hpa 1.5pa/K 1.71V~3.6V 1hpa 300nA 30Kpa~1.1bar I2C、SPI Integrated ADC and digital interface、On-chip calibration and non-volatile storage、Standby mode、On-chip temperature output LGA-8(2x2.5) Pressure Sensors ROHSBoschPressure Sensors
AON7410
DFN-8(3x3)-55℃~+150℃ 1 N-channel 12nC@10V 143pF 2.5V 20W 20mΩ@10V 30V 50A 660pF 77pF N-Channel DFN-8(3x3) MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
ICM-42688-P
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 2KB 7.5uA IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps Motion Event Detection, Synchronization, Timestamp Support LGA-14(2.5x3) Accelerometers ROHSTDK InvenSenseAccelerometersUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)
SS54FSH
SOD-128Schottky DiodesTaiwan Semiconductor
1N4148W
SOD-123150mA 1A 1V@50mA 1uA@75V 400mW 4ns 75V Independent SOD-123 Switching Diodes ROHSSTMicroelectronicsSwitching Diodes
CMT-7525-80-SMT-TR
SMD,7.5x7.5mm-40℃~+85℃ 100mA 2.5V~4.5V 2.5mm 2.73kHz 3.6V 7.5mm 7.5mm 80dB Electromagnetic Passive (Externally Driven) Surface Mount SMD,7.5x7.5mm Buzzers ROHSCUIBuzzers
SS14
SMA(DO-214AC)-55℃~+150℃ 1A 25A 300uA@40V 40V 550mV@1A Independent SMA(DO-214AC) Schottky Diodes ROHSMDDSchottky Diodes
TYPE-C-31-M-12
SMD-30℃~+80℃ 1 10,000 cycles 16P 20V 5A 7.35mm Female Surface Mount, Right Angle Type-C SMD USB Connectors ROHSHRO ElectronicsUSB Connectors
README
README.mdflight-controller-PCB
Parts
130| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C6, C8, C9, C12, C18, C20, C32, C38, C41, C46, C47 |
| 11 | 10k | Resistor_SMD:R_0603_1608Metric | R6, R9, R12, R14, R16, R18, R20, R21, R22, R25, R26 |
| 6 | 1uF | Capacitor_SMD:C_0603_1608Metric | C4, C33, C35, C37, C39, C40 |
| 5 | 10uF | Capacitor_SMD:C_0603_1608Metric | C5, C14, C15, C21, C48 |
| 5 | 47k | Resistor_SMD:R_0603_1608Metric | R28, R29, R30, R31, R32 |
| 4 | 100nF/50v | Capacitor_SMD:C_0603_1608Metric | C30, C31, C34, C36 |
| 4 | 100nf | Capacitor_SMD:C_0603_1608Metric | C26, C27, C28, C29 |
| 4 | 33 | Resistor_SMD:R_0603_1608Metric | R11, R13, R15, R17 |
| 4 | MountingHole | MountingHole:MountingHole_2.1mm | H1, H2, H3, H4 |
| 4 | SS54FSH | Diode_SMD:D_SMA | D3, D4, D5, D6 |
| 4 | UCC27511ADBV | Package_TO_SOT_SMD:SOT-23-6 | U5, U7, U9, U11 |
| 3 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C7, C11, C45 |
| 3 | AON7410 | Package_DFN_QFN:DFN-8-1EP_3x3mm_P0.65mm_EP1.5x2.25mm | U8, U10, U12 |
| 2 | 10uF/25v | Capacitor_SMD:C_0603_1608Metric | C22, C44 |
| 2 | 12pF | Capacitor_SMD:C_0603_1608Metric | C42, C43 |
| 2 | 1k | Resistor_SMD:R_0603_1608Metric | R3, R4 |
| 2 | 2.2uF | Capacitor_SMD:C_0201_0603Metric_Pad0.64x0.40mm_HandSolder | VCAP1, VCAP2 |
| 2 | 220uF/25v | Capacitor_SMD:C_1206_3216Metric | C1bulk1, C2bulk1 |
| 2 | 22uF | Capacitor_SMD:C_0603_1608Metric | C10, C16 |
| 2 | 4.7uH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1, L2 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R23, R24 |
| 2 | 600 ohm 100mHZ | Inductor_SMD:L_Eaton_MCL2012V1 | fb1, fb2 |
| 2 | 75k | Resistor_SMD:R_0603_1608Metric | R1, R10 |
| 2 | MP2315GJ | Package_TO_SOT_SMD:SOT-23-8 | U1, U3 |
| 2 | led | LED_SMD:LED_0603_1608Metric | D1, D2 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C24 |
| 1 | 0.1µF | Capacitor_SMD:C_0603_1608Metric | C19 |
| 1 | 100 | Resistor_SMD:R_0603_1608Metric | R27 |
| 1 | 10K | Resistor_SMD:R_0603_1608Metric | R19 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric | C23 |
| 1 | 1N4148W | Diode_SMD:D_SOD-123 | D7 |
| 1 | 2.2uF | Capacitor_SMD:C_0603_1608Metric | C25 |
| 1 | 22k | Resistor_SMD:R_0603_1608Metric | R5 |
| 1 | 22uF/16v | Capacitor_SMD:C_0603_1608Metric | C17 |
| 1 | 2N7002 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | 31.6k | Resistor_SMD:R_0603_1608Metric | R2 |
| 1 | 52.3k | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 8HMz | Crystal:Crystal_SMD_3215-2Pin_3.2x1.5mm | Y2 |
| 1 | BMP280 | Package_LGA:Bosch_LGA-8_2x2.5mm_P0.65mm_ClockwisePinNumbering | U13 |
| 1 | CMT-7525-80-SMT-TR | Buzzer_Beeper:Buzzer_CUI_CPT-9019S-SMT | LS1 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | j3 |
| 1 | Conn_01x05_Pin | Connector_PinHeader_1.00mm:PinHeader_1x05_P1.00mm_Vertical | J10 |
| 1 | ICM-42688-P | Package_LGA:LGA-14_2x2mm_P0.35mm_LayoutBorder3x4y | U4 |
| 1 | Jumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | M1 front left | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M1 |
| 1 | M2 front right | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M3 |
| 1 | M3 rear right | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M4 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3D-SF | J1 |
| 1 | RC | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | J2 |
| 1 | SS14 | Diode_SMD:D_SMA | D8 |
| 1 | STM32H753VITx | Package_QFP:LQFP-100_14x14mm_P0.5mm | U14 |
| 1 | TYPE-C-31-M-12 | TYPE-C-31-M-12:HRO_TYPE-C-31-M-12 | J9 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U15 |
| 1 | m4 rear left | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | M2 |
| 1 | reciver | Connector_PinHeader_1.27mm:PinHeader_1x04_P1.27mm_Vertical | J8 |
| 1 | ul_AON7410 | Package_DFN_QFN:DFN-8-1EP_3x3mm_P0.65mm_EP1.5x2.25mm | U6 |
The 126 most common of 130 parts.
More from Tamim101/flight-controller-PCB
1Similar boards
- 6 layers47.6 × 41.5 mm
- 2 layers181.1 × 244 mm
Main MagicAlonso rounded
JRegi/MagicAlonso-LineFollower
Repositorio dedicado al desarrollo del velocista profesional MagicAlonso.
412 partsMIT - 4 layers40 × 40 mm
- 2 layers105.7 × 56 mm
- 2 layers80 × 100 mm
- 4 layers100.6 × 67.1 mm
- 4 layers102.8 × 67 mm
Entegre fc
ErdemA33/stm32f405-flight-controller
Open-source ArduPilot-compatible flight controller for fixed-wing UAVs. STM32F405, 4-layer KiCad design, built in 5 modular stages.
129 parts3 - 4 layers65 × 40.1 mm
Aero Zero
ChladpavPy/Aero-Zero
I started this project, because I wanted to build fully autonomous ai drone. When I looked at the flight controllers available on the market, they were full of hardware that I just do not need or just that I could not…
97 parts
Questions
How big is the OLL.E fpv pcb PCB?
It measures 47.6 × 41.5 mm and has 2 copper layers, 1.6 mm thick.
What parts does the OLL.E fpv pcb use?
130 parts, built around the UCC27511ADBV, MP2315GJ-Z, BMP280 and AON7410. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the OLL.E fpv pcb KiCad files?
From the Tamim101/flight-controller-PCB repository on GitHub, at the commit this page was made from: the board is OLL.E fpv_pcb.kicad_pcb and its schematic Flight_Controller_PCB-backups/Flight_Controller_PCB-2026-07-01_121737/Flight_Controller_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the OLL.E fpv pcb design in my own project?
Its repository states no licence, so its author keeps all rights: ask Tamim101 before reusing the design.