
Locklab DAQ
TPierceUCSD/Wireless-motion-capture-data-sycnhronization-system
© 2025 Taylor Pierce, Emerson Noble, Lucas Davis, Jesus Wilkins, Kenneth J. Loh. Licensed under CC BY 4.0.

© 2025 Taylor Pierce, Emerson Noble, Lucas Davis, Jesus Wilkins, Kenneth J. Loh. Licensed under CC BY 4.0.
DAQv3 5 is an open-source printed circuit board by TPierceUCSD, from the TPierceUCSD/Wireless-motion-capture-data-sycnhronization-system repository on GitHub. It is a 4-layer board of 40 × 70 mm with 54 parts on 72 nets, routed with 453 tracks and 91 vias.
It is built around the AD8544ARUZ-REEL, ESP32-C3-WROOM-02-H4 and ADA4807-1ARJ, with the MIC5504-3.3YM5, MCP73831T-2ACI/OT-HXY and MMBT2222A among its other parts. Its parts include 16 capacitors, 16 resistors, 10 ICs, 3 connectors and 2 diodes. It belongs with the ESP32 and RISC-V boards of this library.
© 2025 Taylor Pierce, Emerson Noble, Lucas Davis, Jesus Wilkins, Kenneth J. Loh. Licensed under CC BY 4.0.
A wireless data acquisition architecture that reconstructs analog sensor signals as voltages at the Vicon Lock Lab™ analog input, enabling direct integration of wearable sensor data into optical motion capture data streams without modification to existing laboratory infrastructure.
This repository contains the hardware design files, firmware, and bill of materials associated with the following publication:
Pierce, T.; Noble, E.; Davis, L.; Wilkins, J.; Loh, K.J. "A Wireless Wearable Data Acquisition Architecture for Near Frame-Accurate Synchronization with Optical Motion Capture." Electronics (under review).
├── Hardware/
│ ├── Drill Files/
│ ├── Sender Node/ # Wearable acquisition node
│ │ ├── KiCAD Files/
│ │ └── Sender_Schematic.pdf
│ └── Receiver Node/ # Receiver node
│ ├── KiCAD Files
│ └── Receiver_Schematic.pdf
│
├── Firmware/
│ ├── Receiver_Node/
│ │ └── Receiver_Node.ino # Wearable node firmware (Arduino IDE)
│ └── Wearable_Node/
│ └── Wearable_Node.ino # Receiver node firmware (Arduino IDE)
│
├── BOM/
│ ├── BOM.xlsx # Bill of materials — combined for the wearable and reciever node. Update "# Boards" in each sheet to update the final components list.
│
└── Verification/ # Data and analysis scripts for v1.0.0 (MDPI submission)
├── Data/ # Raw data files (Vicon csv exports)
└── Processing Scripts/ # MATLAB analysis scriptsThe system comprises two hardware nodes:
Wearable (Sender) Node — worn by the subject, acquires up to 8 analog channels at 250 Hz via a 16-bit SPI ADC (AD7689), and transmits data wirelessly using the ESP-NOW protocol on the ESP32-C3.
Receiver Node — mounted adjacent to the Lock Lab™ interface, receives wireless packets and reconstructs analog voltages on up to 8 output channels via a 16-bit SPI DAC (DAC8568), which are wired directly to the Lock Lab™ analog inputs.
Sensor inputs on the wearable node use a resistive voltage divider configuration (0–2.5 V input range). The reference resistor should be selected to match the sensor's nominal resistance to centre the operating point near mid-rail. These components are highlighted in the BOM.
Full component details including part numbers, values, and digikey links are provided in the BOM files. BOM file designed for direct upload to digikey for parts ordering. Note that several components (DAC, 2.5V Reference) are referenced as different components between the BOM and KiCAD file. These are drop in replacements, the BOM contains the intended components (2.5V reference, 16-bit ADC) Any LiPo battery with a JST PH connector should be suitable. It should be noted the hardware does not contain reverse polarity protection. Modified batteries or alternate solutions should reference the schematic to ensure valid configuration.
Firmware is written for the Arduino IDE with the ESP32 board support package.
Requirements:
Flashing:
Firmware/Receiver_Node/Receiver_Node or Firmware/Wearable_Node/Wearable_Node.ino in Arduino IDEThe receiver MAC address must be set in the sender firmware to match your specific receiver board. The receiver's MAC address is printed to Serial on startup when DEBUG_MODE = true.
The MATLAB processing scripts require:
Input data should be exported from Vicon Nexus as CSV files and placed in the MATLAB working directory. File names and trial configuration are set in the user settings block at the top of the script.
| Version | Description |
|---|---|
| v1.0.0 | Version associated with MDPI Electronics submission. Includes verification data and analysis scripts. |
Future versions of this repository are intended to improve system functionality and performance. The v1.0.0 release represents the implementation associated with the MDPI publication; subsequent versions may differ in performance characteristics, and any significant changes will be noted in the version history.
For questions regarding hardware, firmware, or reproduction of results, please contact the corresponding author via the associated publication.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 3k | Resistor_SMD:R_0603_1608Metric | R7, R9, R11, R13, R15, R17, R19, R21 |
| 7 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R24 |
| 6 | 1uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C4, C5, C6 |
| 5 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C10, C11, C12, C13, C14 |
| 5 | 10uF | Capacitor_SMD:C_0603_1608Metric | C7, C8, C9, C15, C16 |
| 2 | AD8544ARUZ-REEL | AD8544:SOP65P640X120-14N | U8, U9 |
| 2 | MIC5504-3.3YM5 | Package_TO_SOT_SMD:SOT-23-5 | U2, U4 |
| 2 | MMBT2222A | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2 |
| 1 | 10118192-0002LF | USB_SMD:AMPHENOL_10118192-0002LF | J1 |
| 1 | 1787072 | 1787072_Contact_16POS:PHOENIX_1787072 | J3 |
| 1 | 300 | Resistor_SMD:R_0603_1608Metric | R23 |
| 1 | AD7689xCP | Package_CSP:LFCSP-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm | U5 |
| 1 | ADA4807-1 | Package_TO_SOT_SMD:SOT-363_SC-70-6 | U6 |
| 1 | COM-16347 | SMD_RGB_COM16347:COM-16347_SPK | LED1 |
| 1 | CP2102N-Axx-xQFN24 | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U3 |
| 1 | ESP32-C3-WROOM-02 | RF_Module:ESP32-C3-WROOM-02 | U1 |
| 1 | JS102011SAQN | JS102011SAQN_SLIDE_SWITCH:SW_JS102011SAQN | S1 |
| 1 | L | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | LOGO | ARMOR LOGO:ARMOR Logo | G*** |
| 1 | LSM6DSO32TR | LSM6DSO32:XDCR_LSM6DSO32TR | U7 |
| 1 | MCP73831T-2ACI/OT | MCP73831T_CHRG:SOT-23-5_MC_MCH | U10 |
| 1 | S2B-PH-SM4-TB | JST:CONN_S2B-PH-SM4-TB_JST | J2 |

TPierceUCSD/Wireless-motion-capture-data-sycnhronization-system
© 2025 Taylor Pierce, Emerson Noble, Lucas Davis, Jesus Wilkins, Kenneth J. Loh. Licensed under CC BY 4.0.

cegea/temperature_node_hw
PCB design for a temperature sensor based on SHT and ESP32


HydrogreenPollub/fuel_cell_control_unit_pcb_fccu_v2_1
Last FCCU version made by Michał Borkowski. All connections are similiar with FCCUv2. Add 2x n-mosfet with Wago conectors on the back side and 2x ADC on the same i2c line

HydrogreenPollub/legacy-pcb-energy-flow-unit
New Energy Flow pcb with step down CC CV converter


HydrogreenPollub/legacy-pcb-hydrogen-cylinder
PCB for Ecson motor driver


It measures 40 × 70 mm and has 4 copper layers, 1.6 mm thick.
54 parts, built around the AD8544ARUZ-REEL, ESP32-C3-WROOM-02-H4, ADA4807-1ARJ and MIC5504-3.3YM5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the TPierceUCSD/Wireless-motion-capture-data-sycnhronization-system repository on GitHub, at the commit this page was made from: the board is Hardware/Wearable Node/KiCAD Files/DAQv3_5.kicad_pcb and its schematic Hardware/Receiver Node/KiCAD Files/DAC.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask TPierceUCSD before reusing the design.