
Walkiepcb
houseofthe051010/ESP32-Walkie-Talkie-V2
This ESP32 Walkie Talkie is redesigned with a SX1262 radio, a PCB, and a full case redesign.

Labs is an open-source printed circuit board by T1mon1k, from the T1mon1k/PCB_Labs_Squad4 repository on GitHub. It is a 2-layer board of 85.3 × 61.3 mm with 62 parts on 124 nets, routed with 415 tracks and 24 vias.
It is built around the AMS1117-3.3, DW01A and TP4056-42-ESOP8, with the SS34 and AO3401A among its other parts. Its parts include 19 resistors, 13 capacitors, 9 diodes, 5 ICs and 2 connectors. It belongs with the STM32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | C 0.1 μF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C4, C6, C7, C8, C9 |
| 4 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | GND1, I2C1, PWR1, SPI1 |
| 4 | R 1 kOhm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R12, R13, R16, R19 |
| 4 | R 10 kOhm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R8, R9, R18 |
| 4 | R 100 Ohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R6, R7, R17 |
| 4 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | Button_1, Button_2, SW1BOOT1, SW2NRST1 |
| 3 | C 10 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C10, C13, C14 |
| 2 | 10 kOhm | Potentiometer_THT:Potentiometer_Bourns_3266Y_Vertical | RV1, RV2 |
| 2 | R 2.2 kOhm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R3 |
| 2 | R 5.1 kOhm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10, R11 |
| 2 | SS34 | Diode_SMD:D_SMA | D8, D9 |
| 1 | 8205A | 8205A:SOT95P285X140-6N | U4 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U5 |
| 1 | AO3401A | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | BAT | LED_SMD:LED_0805_2012Metric | D7 |
| 1 | Battery_Cell | Battery:BatteryHolder_MPD_BH-18650-PC | BT1 |
| 1 | C 10 pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5 |
| 1 | C 100 uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C11 |
| 1 | C 33 pF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C3 |
| 1 | CHARGE | LED_SMD:LED_0805_2012Metric | D6 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | UART1 |
| 1 | Crystal | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y1 |
| 1 | DW01A | Package_TO_SOT_SMD:SOT-23-6 | U3 |
| 1 | LED Blue | LED_SMD:LED_0805_2012Metric | D1 |
| 1 | LED Green | LED_SMD:LED_0805_2012Metric | D4 |
| 1 | LED Orange | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | LED Red | LED_SMD:LED_0805_2012Metric | D2 |
| 1 | PROG_port | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J1 |
| 1 | R 0 Ohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R14 |
| 1 | R 1.5 kOhm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 1 | R 30 Ohm | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | STANDBY | LED_SMD:LED_0805_2012Metric | D5 |
| 1 | STM32F407VGTx | Package_QFP:LQFP-100_14x14mm_P0.5mm | U1 |
| 1 | TP4056-42-ESOP8 | Package_SO:SOIC-8-1EP_3.9x4.9mm_P1.27mm_EP2.41x3.3mm_ThermalVias | U2 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_Horizontal | J2 |

houseofthe051010/ESP32-Walkie-Talkie-V2
This ESP32 Walkie Talkie is redesigned with a SX1262 radio, a PCB, and a full case redesign.


ANSHUMANDOCX/STM32-Walkie-Talkie
This is a Walkie talkie made using STM32 and LoRa



Wudker/Clickfy
Compact ESP32-C3 based BLE multimedia remote with custom PCB, battery monitoring and low-power operation.

MAATHES-THILAK-K/ESP32-S3_FLIGHT_CONTROLLER
A custom-designed flight controller based on the ESP32-S3 module, built for compatibility with the esp-fc firmware and Betaflight-like configuration.

camelNote/RVSP_Pocket
RVSP Pocket is a STM32F4 "soft" fork of the RSVP Nano. RVSP Pocket aims to be a more hardware optimized version of the RVSP Nano, cheaper, and more compact.
It measures 85.3 × 61.3 mm and has 2 copper layers, 1.6 mm thick.
62 parts, built around the AMS1117-3.3, DW01A, TP4056-42-ESOP8 and SS34. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the T1mon1k/PCB_Labs_Squad4 repository on GitHub, at the commit this page was made from: the board is Labs.kicad_pcb and its schematic Labs.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask T1mon1k before reusing the design.