4 layers70.1 × 122.2 mm
Gbc cm4-aio
will-tm/gbc-cm4-aio
This project is a drop-in replacement board that fits and Gameboy Color shell and use the same IPS display as used in GBC kits.
130 parts2
2 layers22 × 30 mm
M.2 to USB V1.0
Supercookiegaming/M.2-to-USB6M.2 2230 to Internal USB 2.0 Header
- Size
- 22 × 30 mm
- Copper layers
- 2
- Thickness
- 0.93 mm
- Parts
- 30
- Nets
- 71
- Pads
- 158
- Tracks, vias
- 279, 96
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 17 Apr 2025
- Updated
- 16 Jun 2026
Overview
M.2 to USB V1.0 is an open-source printed circuit board by Supercookiegaming, from the Supercookiegaming/M.2-to-USB repository on GitHub. It is a 2-layer board of 22 × 30 mm with 30 parts on 71 nets, routed with 279 tracks and 96 vias.
It is built around the TPS61022RWUR and RH100-24.000-9-1015-EXT-TR. Its parts include 13 capacitors, 6 resistors, 4 ICs, 2 connectors and 1 inductor. It belongs with the computers and single-board computers boards of this library.
Main components
2
TPS61022RWUR
VQFN-7(2x2)-40℃~+125℃@(TJ) 1 2.2V~5.5V 3A 3uA 500mV~5.5V 600kHz、1MHz Adjustable Boost Boost Built-in Overcurrent Protection、Light load efficient mode、Load disconnect Yes VQFN-7(2x2) DC-DC Converters ROHSTexas InstrumentsDC-DC Converters
RH100-24.000-9-1015-EXT-TR
SMD3225-4P-40℃~+85℃ 24MHz 60Ω 9pF ±10ppm ±15ppm SMD3225-4P Crystals ROHSRaltronCrystals
README
README.mdM.2-to-USB Adapter Card
The M.2 to USB adapater uses the single USB 2.0 port on the A/E Key M.2 slot to make an USB front panel connector. The board uses the Microchip USB2422 2 port USB 2.0 hub IC. The hub allows 2 usb ports to be connected to the single port on the M.2 slot. This board is designed to handle 0.5 A per USB port, above that current the port will turn off. This was done because the M.2 slot can only provide 6.6 W. The 5V rail is made from the 3.3V found on the M.2 slot via a boost converter.
The board was designed to compatible with OSH Park's 2 layer 0.8mm thick PCB service.
The board is free to use for personal use only.
Parts
30| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100kΩ | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R2, R3, R4, R5 |
| 4 | 10uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C1, C3, C10, C11 |
| 3 | 100nF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C2, C4, C8 |
| 2 | 1uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C6, C7 |
| 2 | C_Small | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C12, C13 |
| 2 | TPS2041CDBVT | Component Library:SOT95P280X145-5N | IC2, IC3 |
| 1 | 100nF | Capacitor_SMD:C_0402_1005Metric | C5 |
| 1 | 12kΩ | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 1uH | Inductor_SMD:L_Bourns_SRN6045TA | L1 |
| 1 | 2.2uF | Capacitor_SMD:C_0402_1005Metric_Pad0.74x0.62mm_HandSolder | C9 |
| 1 | 732kΩ | Resistor_SMD:R_0402_1005Metric_Pad0.72x0.64mm_HandSolder | R6 |
| 1 | APX809-46SRG-7 | Component Library:APX809-SR | U1 |
| 1 | Conn_2Rows-09Pins | Component Library:USB 2.0 Front Header | J2 |
| 1 | LOGO | LOGO | G*** |
| 1 | M.2 Slot | Component Library:NGFF_A+E | J1 |
| 1 | MountingHole_Pad | Component Library:m.2 edge mount hole | H1 |
| 1 | RH100-24.000-9-1015-EXT-TR | Component Library:RH10010000105050TR | Y1 |
| 1 | TPS61022RWUR | Component Library:TPS61022RWUR | PS1 |
| 1 | USB2422T_MJ | Component Library:QFN50P400X400X100-25N-D | IC1 |
Similar boards
- 2 layers89.5 × 26.5 mm
Gopro powerbank
ritaru/gopro-powerbank
A simple 5V/3A output single-18650 cell power bank circuit
29 parts1 - 2 layers96 × 90 mm
- 2 layers81 × 57.7 mm
Hermes
GodOfStrategy/GYACSPEED
Speedometer, accelerometer and a gyroscope for my bicycle, with the XIAO RP2040 as the MCU, with a 1.3" OLED display for the information.
33 parts - 2 layers160.2 × 53.6 mm
- 2 layers105 × 98.1 mm
- 4 layers42 × 27 mm
- 2 layers65 × 56 mm
Teamc carrier
SantiBarrios2002/mtp-f26-teamc
MTP F26 (UPC) Team C workspace: radio link budget, RFM69 firmware, protocol simulator
94 parts
Questions
How big is the M.2 to USB V1.0 PCB?
It measures 22 × 30 mm and has 2 copper layers, 0.93 mm thick.
What parts does the M.2 to USB V1.0 use?
30 parts, built around the TPS61022RWUR and RH100-24.000-9-1015-EXT-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the M.2 to USB V1.0 KiCad files?
From the Supercookiegaming/M.2-to-USB repository on GitHub, at the commit this page was made from: the board is KiCad Files/M.2 to USB V1.0/M.2 to USB V1.0.kicad_pcb and its schematic KiCad Files/M.2 to USB V1.0/M.2 to USB V1.0.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the M.2 to USB V1.0 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Supercookiegaming before reusing the design.