

Robot Tour Peter-2024
Petah
- Size
- 142 × 156 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 128
- Nets
- 176
- Pads
- 837
- Tracks, vias
- 183, 25
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 25 Nov 2024
- Updated
- 7 Jan 2025
Overview
Robot Tour Peter-2024 is an open-source printed circuit board by Stuyoly-Tech, from the Stuyoly-Tech/Robot-Tour-Peter-2024 repository on GitHub, published under the MIT licence. It is a 4-layer board of 142 × 156 mm with 128 parts on 176 nets, routed with 183 tracks and 25 vias.
It is built around the RP2040, ESP32-S3-WROOM-1-N8 and W25Q32JVZPIQ, with the AMS1117-3.3 and ABM8-272-T3 among its other parts. Its parts include 46 capacitors, 36 resistors, 15 switches, 14 ICs and 7 diodes. It belongs with the robots and motor control boards and the ESP32 and RP2040 boards of this library.
Main components
5RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesW25Q32JVZPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 133MHz 2.7V~3.6V 20 Years 32Mbit 3ms SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbondNOR FLASHAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsABM8-272-T3
SMD3225-4P-40℃~+85℃ 10pF 12MHz 50Ω SMD crystal oscillator ±30ppm ±30ppm SMD3225-4P Crystals ROHSAbraconCrystals
README
README.mdParts
128| Qty | Value | Footprint | References |
|---|---|---|---|
| 31 | 100nF | Capacitor_SMD:C_0201_0603Metric | C1, C2, C10, C11, C12, C13, C14, C17, C18, C22, C23, C26, C27, C30, C31, C33 +15 |
| 25 | 1k | Resistor_SMD:R_0201_0603Metric | R1, R11, R12, R13, R17, R18, R19, R20, R21, R22, R23, R24, R29, R30, R31, R32 +9 |
| 8 | SW_Push | Button_Switch_Keyboard:SW_Cherry_MX_1.00u_PCB | SW8, SW9, SW10, SW11, SW12, SW13, SW14, SW15 |
| 5 | 1uF | Capacitor_SMD:C_0201_0603Metric | C4, C15, C16, C28, C40 |
| 4 | 15pF | Capacitor_SMD:C_0201_0603Metric | C19, C20, C24, C25 |
| 4 | 2.2k | Resistor_SMD:R_0201_0603Metric | R25, R26, R27, R28 |
| 4 | 27.4 | Resistor_SMD:R_0201_0603Metric | R9, R10, R14, R15 |
| 3 | RST | Button_Switch_SMD:SW_SPST_TL3342 | SW1, SW3, SW6 |
| 3 | ~{USB_BOOT} | Button_Switch_SMD:SW_DPDT_CK_JS202011JCQN | SW2, SW4, SW7 |
| 2 | 10k | Resistor_SMD:R_0201_0603Metric | R3, R16 |
| 2 | 10uF | Capacitor_SMD:C_0201_0603Metric | C21, C32 |
| 2 | 22nF | Capacitor_SMD:C_0201_0603Metric | C3, C6 |
| 2 | 22uF | Capacitor_SMD:CP_Elec_6.3x5.9 | C29, C44 |
| 2 | 2xAA | Battery:BatteryHolder_Keystone_2462_2xAA | BT1, BT3 |
| 2 | ABM8-272-T3 | Crystal:Crystal_SMD_Abracon_ABM8G-4Pin_3.2x2.5mm | Y1, Y2 |
| 2 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U11, U12 |
| 2 | D | Resistor_SMD:R_0201_0603Metric | D6, D7 |
| 2 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U1, U8 |
| 2 | RP2040_LED | LED_SMD:LED_0603_1608Metric | D4, D5 |
| 2 | SWCLK SWD | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2, J3 |
| 2 | W25Q32JVZP | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U4, U7 |
| 2 | ~ | Package_LGA:Bosch_LGA-14_3x2.5mm_P0.5mm | U3, U9 |
| 2 | ~ | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.75x3.75mm | U2, U6 |
| 2 | ~ | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | U13, U14 |
| 1 | 22k | Resistor_SMD:R_0201_0603Metric | R2 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U5 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D1 |
| 1 | ML | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J4 |
| 1 | ML_LED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | MR | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J5 |
| 1 | MR_LED | LED_SMD:LED_0603_1608Metric | D3 |
| 1 | Micro_SD_Card_Det_Hirose_DM3AT | Connector_Card:microSD_HC_Molex_104031-0811 | J1 |
| 1 | SW_DIP_x02 | Button_Switch_SMD:SW_DIP_SPSTx02_Slide_9.78x7.26mm_W8.61mm_P2.54mm | SW5 |
| 1 | USB_C_Plug_USB2.0 | Connector_USB:USB_C_Receptacle_Molex_105450-0101 | P1 |
| 1 | ~ | Package_DFN_QFN:QFN-16-1EP_3x3mm_P0.5mm_EP1.7x1.7mm | U10 |
Similar boards
- 4 layers101.9 × 75.4 mm

- 2 layers30 × 33.2 mm

- 4 layers50 × 60 mm

- 2 layers54.8 × 75.5 mm

OPENSOURCE REMAKE
MAATHES-THILAK-K/Arduino-SMD
Arduino SMD version with In-Built Bluetooth and Gesture sensor
78 parts2MIT - 4 layers100 × 42 mm

- 4 layers140 × 70 mm

- 2 layers110 × 52 mm

- 2 layers62 × 47 mm

Questions
How big is the Robot Tour Peter-2024 PCB?
It measures 142 × 156 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Robot Tour Peter-2024 use?
128 parts, built around the RP2040, ESP32-S3-WROOM-1-N8, W25Q32JVZPIQ and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Robot Tour Peter-2024 KiCad files?
From the Stuyoly-Tech/Robot-Tour-Peter-2024 repository on GitHub, at the commit this page was made from: the board is Electronics/Electronics.kicad_pcb and its schematic Electronics/Electronics.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Robot Tour Peter-2024 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).