Skip to the content
2 layers40.5 × 34 mmMicrocontroller with STM32, the printed circuit board in 3D

Microcontroller with STM32

Storm00212/STM32-PCB-DESIGN1

Simple design architecture for STM 32 Microcontroller with I2C, UART and SWD hardware protocols

Size
40.5 × 34 mm
Copper layers
2
Thickness
1.6 mm
Parts
32
Nets
50
Pads
132
Tracks, vias
178, 22
Pours
4
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
21 May 2026
Updated
21 May 2026

Overview

Microcontroller with STM32 is an open-source printed circuit board by Storm00212, from the Storm00212/STM32-PCB-DESIGN repository on GitHub. It is a 2-layer board of 40.5 × 34 mm with 32 parts on 50 nets, routed with 178 tracks and 22 vias.

It is built around the STM32F103C8T6 and AMS1117-3.3. Its parts include 13 capacitors, 5 resistors, 4 connectors, 2 ICs and 1 diode. It belongs with the interfaces and adapters boards and the STM32 boards of this library.

Main components

2

README

README.md
text
# STM32 PCB Design

Microcontroller Board Based on STM32F103C8T6

Designed by Paul Muyali | Date: 2026-05-18 | Tool: KiCad EESchema / PCBnew v10.0


Table of Contents

  1. Project Overview
  2. Functional Description
  3. Bill of Materials
  4. Net List and Signal Assignments
  5. PCB Layout Specifications
  6. Design Considerations and Engineering Notes
  7. Manufacturing Requirements
  8. Software and Firmware Development
  9. Revision History
  10. References

1. Project Overview

This repository contains the complete KiCad design files for a compact, self-contained microcontroller board centred on the STMicroelectronics STM32F103C8T6 ARM Cortex-M3 device. The board is intended as a general-purpose embedded development and evaluation platform, providing:

  • USB Micro-B connectivity for power delivery and firmware download via the USB Full-Speed Device peripheral
  • On-board 3.3 V linear power supply sourced directly from USB VBUS
  • High-speed external (HSE) crystal oscillator for accurate system clocking
  • SWD (Serial Wire Debug) interface for in-circuit programming and debugging
  • BOOT0 SPDT switch for bootloader / normal boot mode selection
  • Three 4-pin expansion headers exposing SWD, USART1, and I2C2 signals

The design is executed as a two-copper-layer PCB using predominantly SMD components in 0402 and 0603 package sizes, with through-hole connectors and switches for mechanical robustness. Four M2 mounting holes are provided at the board corners.


2. Functional Description

2.1 Microcontroller — U2 (STM32F103C8T6)

The primary processing element is the STM32F103C8T6, housed in a 48-pin LQFP package (7 × 7 mm, 0.5 mm pitch).

ParameterSpecification
Core ArchitectureARM Cortex-M3, 32-bit RISC
Maximum Clock72 MHz
Flash Memory64 KB
SRAM20 KB
Supply Voltage2.0 V to 3.6 V
Operating Temperature−40 °C to +85 °C
Digital I/O37 GPIO pins (select pins 5 V tolerant)
USBFull-Speed USB 2.0 Device (12 Mbit/s)
USART3 channels (USART1 routed to J3)
I2C2 channels (I2C2 routed to J4)
SPI2 channels
Timers3 general-purpose, 1 advanced-control, 2 basic
ADC2 × 12-bit, up to 16 external channels
Debug InterfaceSWD / JTAG
PackageLQFP-48, 7 × 7 mm, 0.5 mm pitch

29 GPIO pins are designated as no-connect stubs in the schematic, indicating that they are available for user expansion via the three 4-pin headers (J2, J3, J4).


2.2 Power Supply Subsystem — U1 (AMS1117-3.3)

The board derives its operating power exclusively from the USB Micro-B connector (J1). The VBUS line (+5 V nominal) feeds the AMS1117-3.3 low-dropout linear voltage regulator, which produces the 3.3 V rail consumed by all digital circuitry.

ParameterSpecification
DeviceAMS1117-3.3
PackageSOT-223-3 (tab = output, Pin 2)
Input Voltage RangeUp to 15 V max. (1.1 V dropout at 800 mA)
Output Voltage3.3 V (fixed)
Maximum Output Current800 mA
Input CapacitorC2: 22 µF (0805 SMD)
Output CapacitorsC1: 22 µF (0805 SMD), C3: 10 µF (0402 SMD)

2.3 Analog Power Domain (+3.3VA)

Ferrite bead FB1 (120 Ω at 100 MHz, 0603 package) isolates the +3.3V digital rail from the +3.3VA analog rail connected to the STM32 VDDA pin, reducing ADC noise. Capacitors C9 and C10 (1 µF each, 0402) provide local bypass on the analog domain.


2.4 USB Interface — J1

The Wuerth Elektronik 629105150521 USB Micro-B receptacle provides the physical USB interface. The D+ and D− differential pair signals are routed directly to PA12 and PA11 of the STM32, which natively implement the USB Full-Speed Device peripheral.

  • R3, R4 (1.5 kΩ each): Series resistors on D+ and D− for signal integrity and MCU I/O protection
  • R5 (1.5 kΩ): D+ pull-up resistor required by the USB Full-Speed specification to signal device presence to the host
  • The USB ID pin is unconnected, which is the correct configuration for a USB Device-only (non-OTG) implementation

2.5 Crystal Oscillator — Y1

An external high-speed crystal oscillator (HSE) is provided for accurate clock generation. The crystal is mounted in a 3225 (3.2 × 2.5 mm) 4-pin SMD package with ground pads on pins 2 and 4. Two 10 pF load capacitors (C12, C13, 0402) form the Pierce oscillator circuit in conjunction with the STM32 internal inverter amplifier.

Note: The crystal oscillation frequency is not explicitly annotated in the schematic and must be specified at procurement. An 8 MHz crystal is recommended for designs targeting the maximum 72 MHz system clock via the internal PLL (PLLMUL × 9).


2.6 BOOT0 Mode Selection — SW1, R2

SW1 is an E-Switch EG1224 SPDT angled through-hole switch that controls the BOOT0 pin to select the MCU boot source at power-on or after a system reset.

SW1 PositionBOOT0 LevelBoot Mode
Position A — GNDLogic 0 (via R2, 10 kΩ pull-down)Normal Flash boot
Position B — +3.3VLogic 1System bootloader (USB DFU)

Setting SW1 to the +3.3V position and cycling power causes the STM32 to enumerate as a USB DFU device, enabling firmware loading via STM32CubeProgrammer or dfu-util without an external SWD programmer.


2.7 SWD Debug Interface

Serial Wire Debug (SWD) signals SWDIO (PA13) and SWCLK (PA14) are routed to expansion header J2, permitting in-circuit programming and real-time debugging with any SWD-capable probe (e.g., ST-LINK/V2, J-Link, Black Magic Probe). Operating in 2-wire SWD mode frees PA15, PB3, and PB4 from debug-only use.


2.8 Decoupling and Bypass Capacitor Strategy

Designator(s)ValuePackageFunction
C4, C5, C6, C7, C11100 nF0402High-frequency bypass on each VDD/VDDA pin group
C810 nF0402Additional high-frequency bypass
C9, C101 µF0402Mid-frequency bypass on analog supply
C12, C1310 pF0402Crystal oscillator load capacitors
C1, C222 µF0805Bulk storage on LDO input and output
C310 µF0402Secondary bulk, LDO output

2.9 Status LED — D1, R1

A 0603 SMD LED (D1) is provided as a user-controllable visual indicator. The anode connects to +3.3V and the cathode drives through current-limiting resistor R1 (1.5 kΩ, 0402) to the MCU GPIO net /PWR_LED_K. At 3.3 V supply with a typical LED forward voltage of 2.0 V, the forward current is approximately 0.87 mA, well within STM32 GPIO drive capability.


2.10 Expansion Headers — J2, J3, J4

Three 4-pin vertical pin socket headers (2.54 mm pitch) expose key MCU peripheral signals.

ConnectorPin 1Pin 2Pin 3Pin 4
J2 — SWD DebugSWDIO (PA13)SWCLK (PA14)+3.3VGND
J3 — UARTUSART1_TX (PA9)USART1_RX (PA10)+3.3VGND
J4 — I2CI2C2_SCL (PB10)I2C2_SDA (PB11)+3.3VGND

3. Bill of Materials

Designator(s)QtyValue / PartPackage / FootprintDescription
C1, C2222 µFC_0805_2012MetricBulk decoupling, LDO output/input
C3110 µFC_0402_1005MetricSecondary bulk decoupling
C4, C5, C6, C7, C115100 nFC_0402_1005MetricMCU VDD/VDDA high-freq bypass
C8110 nFC_0402_1005MetricUSB D+ filter / additional bypass
C9, C1021 µFC_0402_1005MetricAnalog supply bypass
C12, C13210 pFC_0402_1005MetricCrystal load capacitors
D11LEDLED_0603_1608MetricPower / status indicator LED
FB11120 Ω @ 100 MHzL_0603_1608MetricFerrite bead, analog supply isolation
H1–H44M2MountingHole_2.2mm_M2PCB mounting holes (non-electrical)
J11USB Micro-BUSB_Micro-B_Wuerth_629105150521USB 2.0 Micro-B, power and data
J2, J3, J431×04 Pin Header 2.54 mmPinSocket_1x04_P2.54mm_VerticalI/O expansion connectors
R1, R3, R4, R541.5 kΩR_0402_1005MetricUSB D+/D− series / pull-up, LED current limit
R2110 kΩR_0402_1005MetricBOOT0 pull-down resistor
SW11SPDTSW_E-Switch_EG1224_SPDT_AngledBOOT0 mode selection switch
U11AMS1117-3.3SOT-223-3_TabPin23.3 V LDO linear voltage regulator
U21STM32F103C8T6LQFP-48_7x7mm_P0.5mmARM Cortex-M3 microcontroller
Y11Crystal (3225, 4-pin, GND24)Crystal_SMD_3225-4Pin_3.2x2.5mmHSE crystal oscillator

4. Net List and Signal Assignments

Net NameDescriptionSource / DriverConnected To
VBUSUSB VBUS (+5 V from host)J1 pin 1U1 input, SW1
+3.3VDigital 3.3 V supply railU1 outputU2 VDD, all digital ICs
+3.3VAAnalog 3.3 V supply railFB1 outputU2 VDDA
GNDCommon groundJ1 GNDAll components
/NRSTMCU active-low resetU2 NRSTC11 (reset filter cap)
/BOOTOBOOT0 logic levelSW1 wiperU2 BOOT0
/SW_BOOTOBOOT0 switch nodeSW1R2 pull-down
/HSE_INCrystal oscillator inputY1 pin 1U2 PC14 / OSC_IN
/HSE_OUTCrystal oscillator outputY1 pin 3U2 PC15 / OSC_OUT
/SWDIOSWD data I/OU2 PA13J2 debug header
/SWCLKSWD clockU2 PA14J2 debug header
/USART1_TXUART1 transmitU2 PA9J3 header
/USART1_RXUART1 receiveU2 PA10J3 header
/I2C2_SCLI2C2 clockU2 PB10J4 header
/I2C2_SDAI2C2 dataU2 PB11J4 header
/USB_D+USB differential data positiveJ1 pin 3U2 PA12, R3 series
/USB_D-USB differential data negativeJ1 pin 2U2 PA11, R4 series
/PWR_LED_KLED cathode netD1 cathodeR1 current limit

5. PCB Layout Specifications

5.1 Board Physical Properties

ParameterValue
Board Dimensions~34.5 × 28 mm (mounting hole span)
Board Thickness1.6 mm
Copper Layers2 (F.Cu — signal, B.Cu — power/ground)
Copper Thickness35 µm (1 oz) per layer
Dielectric MaterialFR4, εᵣ = 4.5, tan δ = 0.02
Solder MaskLPI, both sides, tented vias
Mounting Holes4 × M2 (2.2 mm drill, non-plated), corner-mounted
Mounting Hole CoordinatesH1: (82.0, 60.5) mm, H2: (47.5, 60.5) mm, H3: (47.5, 88.5) mm, H4: (82.0, 88.5) mm

5.2 Routing Rules

RuleValue
Signal track width0.3 mm
Power track width0.5 mm
Via outer diameter0.7 mm
Via drill diameter0.3 mm
Total routed segments178
Total vias22

All signal routing is performed on F.Cu (front copper). The B.Cu (back copper) layer is designated as the power/ground layer. Via tenting is applied to both sides.


5.3 Component Placement Summary

  • U2 (STM32F103C8T6): Board centre at (62.8, 74.3) mm — facilitates short routing to all peripheral signals
  • U1 (AMS1117-3.3): Adjacent to J1 to minimise VBUS trace length
  • J1 (USB Micro-B): Board-edge mounted for external cable access
  • Y1 (Crystal): Placed close to STM32 PC14/PC15 pins to minimise oscillator loop area
  • C12, C13 (Crystal load caps): Located immediately adjacent to Y1 and relevant MCU pins
  • C1, C2 (22 µF bulk): Positioned at LDO input and output nodes
  • C4–C11 (decoupling caps): Distributed around U2 supply pins per MCU datasheet guidelines
  • SW1 (BOOT0 switch): Board edge, through-hole for mechanical accessibility
  • J2, J3, J4 (expansion headers): Board edges for external connector access
  • H1–H4 (mounting holes): Corner-mounted at 34.5 × 28 mm span

6. Design Considerations and Engineering Notes

6.1 USB Signal Integrity

  • Series resistors R3 and R4 (1.5 kΩ) damp transmission line reflections and limit over/undershoot at the MCU I/O pins
  • D+ and D− traces must be routed as a matched-length differential pair
  • Pull-up resistor R5 (1.5 kΩ) on D+ is required by the USB Full-Speed specification to signal device presence to the host
  • The USB ID pin is correctly left unconnected for a Device-only (non-OTG) implementation

6.2 Crystal Oscillator Load Capacitance

The effective series load capacitance seen by the crystal is:

text
C_L = (C12 × C13) / (C12 + C13) + C_stray
    = (10 pF × 10 pF) / (10 pF + 10 pF) + C_stray
    = 5 pF + C_stray

Where C_stray is the parasitic capacitance of the PCB traces and MCU pins (typically 2–5 pF for short traces). For a crystal specified at C_L = 10 pF, the values of C12 and C13 may require adjustment based on measured oscillation accuracy.

6.3 LDO Stability with Ceramic Output Capacitors

The AMS1117 series requires an output capacitor ESR in the range of 22 mΩ to several hundred milliohms for guaranteed stability. The 22 µF MLCC (C1, 0805) presents a very low ESR (typically < 10 mΩ). Verification against the AMS1117 stability specification is recommended. A tantalum or electrolytic capacitor may be added in parallel with C1 if instability is observed.

6.4 BOOT0 and USB DFU Bootloader

To enter DFU bootloader mode:

  1. Set SW1 to the +3.3V position (BOOT0 = 1)
  2. Cycle USB power (disconnect and reconnect)
  3. The STM32 will enumerate as a USB DFU device on the host
  4. Load firmware using STM32CubeProgrammer or dfu-util
  5. Return SW1 to the GND position before the next reset to boot from Flash

6.5 Unused GPIO Pins

Per STM32 application note AN4899, all unused GPIO pins should be configured as analog inputs (GPIO_MODE_ANALOG) in firmware to minimise power consumption and prevent floating input oscillation.

6.6 EMC Considerations

  • Ferrite bead FB1 (120 Ω at 100 MHz) isolates digital switching noise from the VDDA analog domain
  • Distributed 100 nF bypass capacitors provide low-impedance bypassing at each MCU supply pin group
  • Crystal placement close to OSC pins minimises the radiating loop area
  • The USB connector shield is unconnected from GND in this revision. For commercial product compliance, a 4.7 nF / 100 V capacitor from shield to GND is recommended for ESD and EMC purposes

7. Manufacturing Requirements

7.1 PCB Fabrication

RequirementSpecification
Board MaterialFR4, Tg ≥ 130 °C
Board Thickness1.6 mm ± 0.1 mm
Copper Layers2
Minimum Track Width0.3 mm
Minimum Track Clearance0.2 mm
Via Drill0.3 mm
Via Pad0.7 mm
Minimum Annular Ring0.2 mm
Solder MaskLPI, green (both sides)
SilkscreenWhite (both sides)
Surface FinishHASL (lead-free) or ENIG
Workmanship StandardIPC Class 2

7.2 Assembly Notes

  • All SMD components are placed on the F.Cu (top) side
  • Through-hole components (J2, J3, J4, SW1, H1–H4) are placed on the top side and soldered from the bottom
  • Reflow soldering per IPC/JEDEC J-STD-020 for SMD components; manual or selective soldering for through-hole
  • U2 (LQFP-48, 0.5 mm pitch): Use a 0.10–0.12 mm stencil with ~15% aperture reduction to prevent solder bridging
  • Y1 (3225, 4-pin): Ensure GND pads (pins 2 and 4) are soldered to a low-impedance ground connection
  • U1 (SOT-223): The exposed tab (pin 2) must be soldered to the PCB thermal pad

7.3 Test and Inspection

  • Visual inspection per IPC-A-610 Class 2
  • Apply USB power and verify +3.3V rail within 3.3 V ± 2%
  • Verify LED D1 illuminates upon power-on (firmware-dependent)
  • Connect SWD probe to J2 and confirm MCU identification
  • Enumerate board as USB device and confirm host recognition
  • Toggle SW1 and verify BOOT0 pin logic level transitions

8. Software and Firmware Development

8.1 Toolchain

ToolRecommendation
IDESTM32CubeIDE
HAL / DriversSTM32CubeF1 (HAL / LL for STM32F1 series)
CompilerGCC ARM Embedded
SWD ProgrammingSTM32CubeProgrammer or ST-LINK Utility
DFU ProgrammingSTM32CubeProgrammer or dfu-util

8.2 Recommended Clock Configuration (8 MHz HSE → 72 MHz SYSCLK)

c
// RCC configuration for maximum performance
// HSE = 8 MHz crystal (Y1)
// SYSCLK = 72 MHz via PLL

RCC_OscInitStruct.OscillatorType      = RCC_OSCILLATORTYPE_HSE;
RCC_OscInitStruct.HSEState            = RCC_HSE_ON;
RCC_OscInitStruct.HSEPredivValue      = RCC_HSE_PREDIV_DIV1;
RCC_OscInitStruct.PLL.PLLState        = RCC_PLL_ON;
RCC_OscInitStruct.PLL.PLLSource       = RCC_PLLSOURCE_HSE;
RCC_OscInitStruct.PLL.PLLMUL          = RCC_PLL_MUL9;   // 8 MHz × 9 = 72 MHz

RCC_ClkInitStruct.ClockType           = RCC_CLOCKTYPE_SYSCLK |
                                         RCC_CLOCKTYPE_HCLK   |
                                         RCC_CLOCKTYPE_PCLK1  |
                                         RCC_CLOCKTYPE_PCLK2;
RCC_ClkInitStruct.SYSCLKSource        = RCC_SYSCLKSOURCE_PLLCLK;
RCC_ClkInitStruct.AHBCLKDivider       = RCC_SYSCLK_DIV1;   // HCLK  = 72 MHz
RCC_ClkInitStruct.APB1CLKDivider      = RCC_HCLK_DIV2;     // PCLK1 = 36 MHz (max)
RCC_ClkInitStruct.APB2CLKDivider      = RCC_HCLK_DIV1;     // PCLK2 = 72 MHz

// Flash latency: 2 wait states required for SYSCLK > 48 MHz
__HAL_FLASH_SET_LATENCY(FLASH_LATENCY_2);

8.3 USB Peripheral Notes

  • USB pins PA11 (USB_DM) and PA12 (USB_DP) must not be remapped
  • Pull-up resistor R5 (1.5 kΩ) is permanently connected; the device will enumerate immediately upon VBUS application if the USB peripheral is initialised
  • For applications requiring delayed enumeration, defer USB peripheral initialisation until the firmware is ready to respond to host requests

9. Revision History

RevisionDateAuthorDescription
1.02026-05-18Paul MuyaliInitial release. Complete schematic and two-layer PCB layout with all components placed and routed.

10. References

  1. STMicroelectronics. STM32F103C8 Datasheet (DS5319). Rev. 17. STMicroelectronics, 2023.
  2. STMicroelectronics. STM32F10xxx Reference Manual (RM0008). Rev. 21. STMicroelectronics, 2021.
  3. STMicroelectronics. AN4899 — STM32 microcontroller GPIO hardware settings and low-power consumption. STMicroelectronics, 2021.
  4. Advanced Monolithic Systems. AMS1117 Datasheet. Revision B. AMS, 2015.
  5. USB Implementers Forum. Universal Serial Bus Specification, Revision 2.0. USB-IF, 2000.
  6. Wuerth Elektronik. WR-COM USB Micro-B Receptacle 629105150521 Datasheet. Wuerth Elektronik, 2020.
  7. KiCad EDA. KiCad 10.0 Documentation. https://docs.kicad.org
  8. IPC. IPC-2221B — Generic Standard on Printed Board Design. IPC, 2012.
  9. IPC. IPC-A-610G — Acceptability of Electronic Assemblies. IPC, 2017.

This document was generated from KiCad project files: Microcontroller_with_STM32.kicad_sch and Microcontroller_with_STM32.kicad_pcb

Parts

32
QtyValueFootprintReferences
5100nCapacitor_SMD:C_0402_1005MetricC4, C5, C6, C7, C11
41k5Resistor_SMD:R_0402_1005MetricR1, R3, R4, R5
4MountingHoleMountingHole:MountingHole_2.2mm_M2H1, H2, H3, H4
3Conn_01x04_PinConnector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_VerticalJ2, J3, J4
210pCapacitor_SMD:C_0402_1005MetricC12, C13
21uCapacitor_SMD:C_0402_1005MetricC9, C10
222uCapacitor_SMD:C_0805_2012MetricC1, C2
110kResistor_SMD:R_0402_1005MetricR2
110nCapacitor_SMD:C_0402_1005MetricC8
110uCapacitor_SMD:C_0402_1005MetricC3
1120RInductor_SMD:L_0603_1608MetricFB1
1AMS1117-3.3Package_TO_SOT_SMD:SOT-223-3_TabPin2U1
1Crystal_GND24Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mmY1
1LEDLED_SMD:LED_0603_1608MetricD1
1STM32F103C8T6Package_QFP:LQFP-48_7x7mm_P0.5mmU2
1SW_SPDTButton_Switch_SMD:SW_SPDT_PCM12SW1
1USB_B_MicroConnector_USB:USB_Micro-B_Wuerth_629105150521J1

Similar boards

  • 2 layers68 × 40 mmStm32-io extend, the printed circuit board in 3D

    Stm32-io extend

    hardenedlinux/cheap-pcb

    Cheap PCB: Better understanding the current status of hardware supply chain

    44 parts170CC0-1.0
  • 2 layers99.1 × 58.4 mmHEAT, the printed circuit board in 3D

    HEAT

    milar111/HEAT

    An open-source STM32 SMD assembly station for precision soldering. Uses a custom Smart Pulse & Coast algorithm to drive 400W mains heaters via SSR. Features OLED UI, NTC feedback, and safety cooling.

    57 parts9
  • 2 layers71.3 × 25.4 mmUSB DALI, the printed circuit board in 3D

    USB DALI

    even-notodd/USB-DALI

    USB-DALI interface converter

    43 parts4
  • 2 layers78 × 60 mmDC Motor Controller, the printed circuit board in 3D

    DC Motor Controller

    minhle4397/Line-Follower-Robot-v2

    Improved Hardware and Firmware for Line Follower Robot

    53 parts3
  • 4 layers36 × 36 mmTrackMAG, the printed circuit board in 3D

    TrackMAG

    mupfdev/TrackMAG

    An open hardware development board primarily intended for the development of accessible input devices.

    58 parts3
  • 2 layers154.7 × 113 mmDeskMixer, the printed circuit board in 3D

    DeskMixer

    RaduAndre/DeskMixer

    DeskMixer is a software that allows control of application volumes with real sliders, and action mapping on buttons using arduino like platforms. The project was inspired originally by deej.

    113 parts3
  • 2 layers42 × 33 mmSTM32 course, the printed circuit board in 3D

    STM32 course

    abda-s/STM32-Phill-s-Lab-PCB-Course

    A beginner-friendly introduction to STM32 hardware design and KiCad

    32 parts2
  • 2 layers53.3 × 35.6 mmStm32 minimal dev, the printed circuit board in 3D

    Stm32 minimal dev

    amrithHN/stm32_minimal_dev

    stm32 based minimal dev board

    33 parts2GPL-3.0

Questions

How big is the Microcontroller with STM32 PCB?

It measures 40.5 × 34 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Microcontroller with STM32 use?

32 parts, built around the STM32F103C8T6 and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Microcontroller with STM32 KiCad files?

From the Storm00212/STM32-PCB-DESIGN repository on GitHub, at the commit this page was made from: the board is Microcontroller with STM32.kicad_pcb and its schematic Microcontroller with STM32.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Microcontroller with STM32 design in my own project?

Its repository states no licence, so its author keeps all rights: ask Storm00212 before reusing the design.