Skip to the content
2 layers435 × 132 mmKEEB, the printed circuit board in 3D

It's a 100% ANSI mechanical keyboard featuring a Raspberry Pi Pico as the brains.

Size
435 × 132 mm
Copper layers
2
Thickness
1.6 mm
Parts
209
Nets
144
Pads
788
Tracks, vias
733, 7
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
19 Apr 2026
Updated
2 May 2026

Overview

KEEB is an open-source printed circuit board by Sash-Reek2010, from the Sash-Reek2010/The-Mech repository on GitHub. It is a 2-layer board of 435 × 132 mm with 209 parts on 144 nets, routed with 733 tracks and 7 vias.

Its parts include 104 diodes, 104 switches and 1 IC. It belongs with the keyboards and input boards and the RP2040 boards of this library.

README

README.md

The Mech

A 100% mechanical keyboard with the Raspberry Pi Pico as its brains! It features 104 Akko V3 Matcha Green keyswitches with 3D printed keycaps and Durock Clear Screw-In stabilizers. The PCB itself is housed inside a 3D printed case which is held down by M4 screws.

main zine zine 3

main zine.pdf

Why a keyboard?

I recently started learning Fusion and my laptop couldn't run it AT ALL so I borrowed my dad's pc. That's when I first encoutered the worst keyboard of my life. I got so used to the laptop keyboard that normal detached ones feel extremely off to me. So to combat that I decided to make a mechanical keyboard! Plus I've never dealt with firmware and KMK is supposed to be really really easy and beginner friendly. And the other side reason is that I'm really bad at soldering, so this should help me improve that too. (104 switches is a lot of pins to solder T-T)

zine 2

Layout

I'm used to the numpad in my laptop so I decided to choose a 100% layout. I'd say its pretty rare to find a 100% these days!

keyboard-layout

The Main

This includes all the hardware stuff that went into the making of this project.

Schematic

The schematic for this project was made in KiCAD. The 26 GPIO pins were barely enough for the switch matrix but it did the job.

image image

The PCB

The PCB for this project was made in KiCAD again! Most of the footprints used are from the internet but some are slightly edited to fit my project.

image image image

PCB Render

image

Case

I made the case in Fusion 360! It is also split into parts which can be printed with a build volume of less than 180mm.

case 1 case 2

BOM

The full BOM is in the repo files as a csv. The shortened version without links and cost is as follows.
Or read it here! https://docs.google.com/spreadsheets/d/1H-eOUtyDmBi-_5e-qRuBTTzMEN6aQgQbRGRCWlnd5h8/edit?usp=sharing
Total cost ~ 85-100 USD depending on location and cost of PCB fab.

ComponentDescriptionUnits
Akko V3 Matcha GreenKeyswitches104
Durock Clear Screw-In StabilizersStabilizers7
Raspberry Pi PicoMicrocontroller1
M4 Screws 45mmScrews for mounting10
Keeb PCBPCB1
1N414Diodes104

Assembly Instructions

(Before we start, you must have all the components to build it, including the PCB which you can order using the gerbers in the assets, and all the 3D printed parts!)
Solder all the diodes, keyswitches and the pico into the PCB carefully taking into account the polarity of the diode.
Screw the stabilizers into their respective drill holes.
Assemble the base of the keyboard case. Place the PCB inside. (Use a thin layer of felt ot cotton if you feel the keyswitches are scratching against the case)
Screw on the top plate in pieces using M4 Screws (Use heatset inserts if you want!)
Push in the printed keyswitches to all the keys. (You can modify the print files to add text on each key too!)
Then follow the firmware guide to get your working keyboard!

Firmware Flash Instructions

Hold down the BOOTSELECT button on the Raspberry Pi Pico and connected to the computer via USB.
Then download the Circuit Python.uf2 file from the assets and drag it into the new drive which appears. (Named RP1-RP2)
The file now has Circuit Python flashed!
Download the KMK folder from assets and drag it into the drive.
Then drag in the KMK.py file into the folder.
And thats it!

Final Thoughts

Challenges

I learnt way too much through this project. I got to know what a diode was and also switch matrices. I learnt to make my own keycaps and also how to use the Raspberry Pi Pico. But at the same time I faced a lot of trouble along the way. The most notable would be making the case for this. I spent a long time export svg files from KiCAD and using the Keyboard Layout Editor to get a sketch that I could just extrude and mae a case. But in the end I had to just manually draw the sketch for the best fit. I also had some problems with stabilizers and their mounting holes. This was one of the first things I made for this project!

KEEB!

Thanks for reading! Hope you have fun with the build :3 -Sashreek!

Parts

209
QtyValueFootprintReferences
104DDIODE:Diode_DO-35D1, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D100, D101, D102, D103, D104 +88
86SW_Push_45degsash:MX_PCB_1.00uSW1, SW2, SW10, SW11, SW12, SW13, SW14, SW15, SW16, SW17, SW18, SW19, SW100, SW101, SW102, SW104 +70
7SW_Push_45degsash:MX_PCB_1.25uSW92, SW93, SW94, SW96, SW97, SW98, SW99
2SW_Push_45degKeyswitches:CherryMX_2.25u_StabWireTopSW71, SW75
2SW_Push_45degsash:MX_PCB_1.50uSW38, SW51
2SW_Push_45degKeyswitches:CherryMX_2.00u_PCB_StabWireTop TRUE ROTATEDSW58, SW91
2SW_Push_45degKeyswitches:CherryMX_2.00u_StabWireTopSW30, SW103
1RASPBERRY_PI_PICOSASHREK:RASPBERRY_PI_PICOU1
1SW_Push_45degsash:MX_PCB_1.75uSW59
1SW_Push_45degKeyswitches:CherryMX_6.25u_StabWireTopSW95
1SW_Push_45degKeyswitches:CherryMX_2.75u_StabWireTopSW86

Similar boards

  • 2 layers152 × 88 mmRFBitBangerNano, the printed circuit board in 3D

    RFBitBangerNano

    profdc9/RFBitBanger

    A QRP digital transceiver created from readily available parts for off-the-grid maintenance

    209 parts222
  • 2 layers337.2 × 122.6 mmCordillera, the printed circuit board in 3D

    Cordillera

    coarse/Cordillera

    Cordillera - Alice layout keyboard PCB

    209 parts52
  • 2 layers371.6 × 127.6 mmNumDiscipline pcb, the printed circuit board in 3D

    NumDiscipline pcb

    ericrlau/NumDiscipline

    Modified CFTKB Discipline with num pad

    209 parts15GPL-3.0
  • 2 layers160 × 200 mmRetro programmer, the printed circuit board in 3D

    Retro programmer

    lynchaj/duodyne

    Duodyne is a hobbyist retrocomputer system designed to run ROMWBW. It is comprised of modules on a system bus

    209 parts15
  • 2 layers70 × 99 mmCC1, the printed circuit board in 3D

    CC1

    etherkit/CC1

    CC1 CW QRP Transceiver

    209 parts11
  • 2 layers253 × 169.1 mmDragon32, the printed circuit board in 3D

    Dragon32

    jimbro1000/Dragon32Issue2

    Recreation of early Dragon 32 mainboard

    209 parts8MIT
  • 2 layers388.9 × 93.7 mmGear80 hotswap, the printed circuit board in 3D

    Gear80 hotswap

    cosmosalad/Gear80

    Gear80 is a 80% keyboard based on the rp2040.

    209 parts7MIT
  • 2 layers100 × 75 mmDisplay, the printed circuit board in 3D

    Display

    DLaxV-Community-Projects-Hub/Open-Shot-Clock

    Build your own DIY Shot Clock

    209 parts5CERN-OHL-P-2.0

Questions

How big is the KEEB PCB?

It measures 435 × 132 mm and has 2 copper layers, 1.6 mm thick.

What parts does the KEEB use?

209 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the KEEB KiCad files?

From the Sash-Reek2010/The-Mech repository on GitHub, at the commit this page was made from: the board is PCB/KiCAD/KEEB.kicad_pcb and its schematic PCB/KiCAD/KEEB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the KEEB design in my own project?

Its repository states no licence, so its author keeps all rights: ask Sash-Reek2010 before reusing the design.