

STMPill
A dev board for STM32WB55REV6 that includes RF for Bluetooth / LE, Thread, & Zigbee. Includes GPIO ports, ST-Link via TC2030 by Tag Connect, and USB-UART
- Size
- 40 × 55.5 mm
- Copper layers
- 4
- Thickness
- 1.62 mm
- Parts
- 69
- Nets
- 98
- Pads
- 328
- Tracks, vias
- 803, 264
- Pours
- 19
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 6 Jun 2026
- Updated
- 12 Jun 2026
Overview
STMPill is an open-source printed circuit board by Reekoru, from the Reekoru/STM32WB55REV6_Board repository on GitHub. It is a 4-layer board of 40 × 55.5 mm with 69 parts on 98 nets, routed with 803 tracks and 264 vias.
It is built around the DLF162500LT-5028A1, TPS78233DDCR and USBLC6-2SC6, with the 1N5819WS, SM4007 and SS8050 among its other parts. Its parts include 25 capacitors, 13 resistors, 6 diodes, 5 connectors and 4 ICs. It belongs with the radio and wireless and interfaces and adapters boards and the STM32 boards of this library.
Main components
7DLF162500LT-5028A1
SMD-4P,1.6x0.8mm-40℃~+85℃ 0.33dB 2.4GHz~2.5GHz 49.2dB 50Ω Low Pass SMD-4P,1.6x0.8mm RF Filters ROHSTDKRF FiltersTPS78233DDCR
TSOT-23-5-40℃~+125℃@(Tj) 1 108uVrms 130mV@(150mA) 150mA 3.3V 40dB@(10Hz) 420nA 5.5V Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)1N5819WS
SOD-3231 Independent 1A 25A 40V 500uA@40V 600mV@1A SOD-323 Schottky Diodes ROHSGuangdong HottechSchottky DiodesSM4007
MELFMELF Diodes - General Purpose ROHSYONGYUTAIDiodes - General PurposeSS8050
SOT-323-55℃~+150℃ 1 NPN 1.5A 100MHz 100nA 200 25V 300mW 500mV 5V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)SS8550
SOT-23-55℃~+150℃ 1 PNP 1.5A 100MHz 100nA 120 25V 300mW 500mV 5V PNP SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
README
README.mdSTM32WB55REV6 Custom Development Board
A compact, custom-designed development board for the STM32WB55REV6 dual-core Bluetooth Low Energy (BLE) and Zigbee microcontroller. Designed in KiCad, this board features a modern USB-C interface for power/data, a dedicated UART interface for debugging, and a space-saving Tag-Connect TC2030 footprint for SWD programming.
Features
- MCU: STM32WB55REV6 (Dual-core Arm® Cortex®-M4 @ 64 MHz with FPU, Cortex-M0+ @ 32 MHz for network/radio).
- Connectivity: On-board RF circuitry and antenna for 2.4 GHz BLE 5.4, Zigbee, and Thread.
- Power: USB-C connector with TPS78233DDC 3.3V regulator supplying up to 150 mA.
- Programming/Debugging: SWD via a headless Tag-Connect TC2030 footprint (no-legs/legged variant).
- Serial Communication: Dedicated UART breakout header for easy terminal debugging.
- Peripherals:
- 1x User LED (connected to Pin
PB9) - USB-UART (connected to Pin
PA9[TX], PinPA10[RX]) - 1x Reset Button, 1x Boot Button
- External 32.768 kHz LSE Crystal, 32 MHz HSE Crystal
- 1x User LED (connected to Pin
Hardware Overview
Pinout Configuration
| Interface | Pin Name | STM32WB55 Pin | Description |
|---|---|---|---|
| UART | TX / RX | PA9 / PA10 | Debug Serial Port |
| SWD | SWO / SWDIO / SWCLK | PB3 / PA13 / PA14 | Tag-Connect TC2030 Programming |
| User LED | LED1 | PB9 | Active [High/Low] indicator |
Power Supply
The board is powered via the USB-C connector. The input 5V is regulated down to 3.3V for the MCU and RF front end.
- Maximum input voltage: 5.5V
- Operating voltage: 3.3V
Programming and Debugging
Required Hardware
To flash and debug this board, you will need:
- An ST-LINK V2, V3, or a Segger J-Link debugger.
- A Tag-Connect TC2030-IDC (or TC2030-IDC-NL) cable along with the corresponding retaining clip if using the no-legs version.
SWD Pinout (TC2030 Footprint)
The Tag-Connect footprint maps to the following standard SWD layout:
- Pin 1: VCC (3.3V)
- Pin 2: SWDIO
- Pin 3: NRST (Reset)
- Pin 4: SWCLK
- Pin 5: GND
- Pin 6: SWO (Optional trace capture)
Flashing via STM32CubeProgrammer
- Connect the TC2030 cable to the board and your ST-LINK debugger.
- Open STM32CubeProgrammer, select ST-LINK as the interface, and click Connect.
- Browse for your compiled binary/hex file and click Start Programming.
Parts
69| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.1uF | Capacitor_SMD:C_0402_1005Metric | C2, C3, C4, C5, C6, C7, C10, C13, C16, C18, C20, C22 |
| 9 | 1k | Resistor_SMD:R_0402_1005Metric | R3, R4, R5, R6, R9, R10, R11, R12, R13 |
| 7 | 4.7uF | Capacitor_SMD:C_0402_1005Metric | C1, C17, C19, C21, C23, C24, C25 |
| 4 | LED | Diode_SMD:D_0402_1005Metric | D1, D2, D3, D4 |
| 3 | 5.1k | Resistor_SMD:R_0402_1005Metric | R2, R7, R8 |
| 3 | Fiducial | Fiducial:Fiducial_0.5mm_Mask1mm | FID1, FID2, FID3 |
| 2 | 10pF | Capacitor_SMD:C_0402_1005Metric | C11, C12 |
| 2 | SW_Push | easyeda2kicad:KEY-SMD_L3.9-W3.0-LS5.0-EH | SW1, SW2 |
| 1 | 0.1pF | Capacitor_SMD:C_0402_1005Metric | C14 |
| 1 | 0.3pF | Capacitor_SMD:C_0402_1005Metric | C8 |
| 1 | 0.8pF | Capacitor_SMD:C_0402_1005Metric | C9 |
| 1 | 100R | Resistor_SMD:R_0402_1005Metric | R1 |
| 1 | 10nF | Capacitor_SMD:C_0402_1005Metric | C15 |
| 1 | 10nL | Inductor_SMD:L_0402_1005Metric | L3 |
| 1 | 10uL | Inductor_SMD:L_0805_2012Metric | L2 |
| 1 | 1N5819WS | Diode_SMD:D_SOD-323 | D5 |
| 1 | 2.7nH | Inductor_SMD:L_0402_1005Metric | L1 |
| 1 | 32.768kHz | jej:SMD3215-2P | Y1 |
| 1 | 32MHz | Crystal:Crystal_SMD_2016-4Pin_2.0x1.6mm | X1 |
| 1 | BOOT0_Jumper | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | CP2102N-Axx-xQFN24 | Package_DFN_QFN:QFN-24-1EP_4x4mm_P0.5mm_EP2.6x2.6mm | U2 |
| 1 | Conn_01x20_L | Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_Vertical | J4 |
| 1 | Conn_01x20_R | Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_Vertical | J5 |
| 1 | Conn_Coaxial | Connector_Coaxial:U.FL_Hirose_U.FL-R-SMT-1_Vertical | J1 |
| 1 | DLF162500LT-5028A1 | easyeda2kicad:FILTER-SMD_0603-4P-L1.6-W0.8-L-1 | FL1 |
| 1 | LOGO | LOGO | G*** |
| 1 | NRST_Jumper | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | SM4007 | Diode_SMD:D_SOD-123F | D6 |
| 1 | SS8050 | Package_TO_SOT_SMD:SOT-23 | Q3 |
| 1 | SS8550 | Package_TO_SOT_SMD:SOT-23 | Q1 |
| 1 | STM32WB55REVx | Package_DFN_QFN:QFN-68-1EP_8x8mm_P0.4mm_EP6.4x6.4mm | U1 |
| 1 | TC2030 | Connector:Tag-Connect_TC2030-IDC-FP_2x03_P1.27mm_Vertical | J2 |
| 1 | TPS78233DDC | Package_TO_SOT_SMD:SOT-23-5 | U3 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | USB_C_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J3 |
Similar boards
- 2 layers35.4 × 35.4 mm

- 2 layers40.6 × 66 mm

- 4 layers243.8 × 171.5 mm

- 2 layers70 × 65 mm

Fluepdot
Fluepke/Fluepdot
Project for controlling Annax flipdot panels used by the Berliner Verkehrsbetriebe
116 parts17AGPL-3.0 - 2 layers100 × 34 mm

- 2 layers101.2 × 199.1 mm

- 4 layers243.8 × 245.5 mm

Neotron Common Hardware
Neotron-Compute/Neotron-Common-Hardware
Contains KiCad footprints and symbols shared across multiple Neotron projects.
287 parts4CC-BY-SA-4.0 - 2 layers100 × 120 mm

FlipperKapr
krasavic3-wittmayer/FlipperKapr
Flipper Kapr is a DIY Arduino-based experimental device, inspired by tools like Flipper Zero. Its purpose is learning, experimentation, and exploration of embedded systems and communication protocols, not hacking or…
60 parts3MIT
Questions
How big is the STMPill PCB?
It measures 40 × 55.5 mm and has 4 copper layers, 1.62 mm thick.
What parts does the STMPill use?
69 parts, built around the DLF162500LT-5028A1, TPS78233DDCR, USBLC6-2SC6 and 1N5819WS. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the STMPill KiCad files?
From the Reekoru/STM32WB55REV6_Board repository on GitHub, at the commit this page was made from: the board is STMPill.kicad_pcb and its schematic STMPill.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the STMPill design in my own project?
Its repository states no licence, so its author keeps all rights: ask Reekoru before reusing the design.