

NanoGris
Arduino Nano version of Mutable Instruments Grids
- Size
- 164.6 × 108 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 112
- Nets
- 79
- Pads
- 382
- Tracks, vias
- 594, 0
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 28 Mar 2020
- Updated
- 15 Oct 2022
Overview
NanoGris is an open-source printed circuit board by Quinienl, from the Quinienl/NanoGris repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 164.6 × 108 mm with 112 parts on 79 nets, routed with 594 tracks and 0 vias.
It is built around the 74HC595 and L7805. Its parts include 45 resistors, 16 capacitors, 8 connectors, 6 ICs and 6 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
274HC595
SOP-16-40℃~+85℃ 1 100ns@5V,50pF 10MHz 2V~6V 74HC 8 Serial-to-Serial or Parallel Tri-State SOP-16 Shift Registers ROHSGRShift RegistersL7805
TO-220ST0℃~+125℃@(Tj) 1 1.2A 20V 2V@(1A) 42uV 500uA 5V 73dB@(120Hz) Fixed Positive Short Circuit Protection TO-220ST Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSOSENVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
README
README.mdNanoGrids
Arduino Nano version of Mutable Instruments Grids
Made this version with Thru Hole parts and a Arduino Nano. Schematics are heavely based on Mutable Instruments schematics. This is not a Mutable Instuments product.
Note: panel hole for button might be a bit to big or small (depends if you use buttoncaps)
I made this for my own and would like to share it with you. I'm doing this as a hobby so expect support to be like that to ;) Everything at your own risk..
Some info on my website that might help
https://www.quinie.nl/category/diy/nanogris/
https://www.quinie.nl/nanogris-gallery/
If you don not want to order boards yourself please check out my shop. https://www.quinie.nl/shop/
hex file for uploading here https://www.quinie.nl/nanogris-the-hex-file/
Update: 6-8-2021 I updated the name of the module. The current version is 0.041
Older boards will have the same function. Did add some better ground planes. Some silkscreen additions to make build easier and changed the footprint of the potentiometer for better fit.
Parts
112| Qty | Value | Footprint | References |
|---|---|---|---|
| 30 | 100k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R1, R2, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20, R21, R22, R23 +14 |
| 8 | 1k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R32, R33, R34, R35, R36, R37, R38, R39 |
| 7 | 10k | Potentiometer_THT:Potentiometer_Alps_RK09K_Single_Vertical_round | P_CH1, P_CH2, P_CH3, P_RND1, P_TEMPO1, P_X1, P_Y1 |
| 7 | 10nf | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C1, C2, C5, C6, C8, C9, C12 |
| 5 | 100nf | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mm | C3, C4, C7, C10, C16 |
| 4 | 100r | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R25, R26, R27, R28 |
| 3 | MCP6002_1 | Package_DIP:DIP-8_W7.62mm | U1, U2, U3 |
| 2 | 0.47uf | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C11, C15 |
| 2 | 10r | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R29, R30 |
| 2 | 10uf | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C13, C14 |
| 2 | 1n4148 | Diode_THT:D_DO-34_SOD68_P7.62mm_Horizontal | D5, D6 |
| 2 | 2N3904 | Package_TO_SOT_THT:TO-92_Wide | Q1, Q2 |
| 2 | Conn_01x10 | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J7, J13 |
| 2 | Conn_01x10 | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J14, J15 |
| 2 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H1, H2 |
| 1 | 10k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_Horizontal | R31 |
| 1 | 74HC595 | Package_DIP:DIP-16_W7.62mm | U6 |
| 1 | Arduino_Nano_v2.x | Module:Arduino_Nano | A1 |
| 1 | CH1 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH1 |
| 1 | CH1 | LED_THT:LED_D3.0mm | D1 |
| 1 | CH1_ACC | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH1_AC1 |
| 1 | CH2 | LED_THT:LED_D3.0mm | D2 |
| 1 | CH2 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH2 |
| 1 | CH2_ACC | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH2_AC1 |
| 1 | CH3 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH3 |
| 1 | CH3 | LED_THT:LED_D3.0mm | D3 |
| 1 | CH3_ACC | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH3_AC1 |
| 1 | CLK | LED_THT:LED_D3.0mm | D4 |
| 1 | CV_CH1 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH1_FILL1 |
| 1 | CV_CH2 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH2_FILL1 |
| 1 | CV_CH3 | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CH3_FILL1 |
| 1 | CV_CLOCK | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CLOCK1 |
| 1 | CV_RESET | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | RESET1 |
| 1 | CV_RND | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | RND2 |
| 1 | CV_X | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | X1 |
| 1 | CV_Y | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | Y1 |
| 1 | ClockOutput | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | CLK1 |
| 1 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J16 |
| 1 | Conn_01x12 | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J11 |
| 1 | Conn_01x12 | Connector_PinSocket_2.54mm:PinSocket_1x12_P2.54mm_Vertical | J10 |
| 1 | Conn_02x05_Odd_Even | Connector_IDC:IDC-Header_2x05_P2.54mm_Vertical | J12 |
| 1 | Fiducial | Symbol:OSHW-Logo2_7.3x6mm_SilkScreen | FID1 |
| 1 | Fiducial | Symbol:OSHW-Logo2_14.6x12mm_SilkScreen | FID2 |
| 1 | L7805 | Package_TO_SOT_THT:TO-220-3_Vertical | U4 |
| 1 | LM4040LP-5 | Package_TO_SOT_THT:TO-92_Wide | U5 |
| 1 | RandomGate | Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHoles | RND1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm | RESET2 |
Similar boards
- 2 layers81.3 × 96.5 mm

- 2 layers100 × 100 mm

- 2 layers125.5 × 96.1 mm

- 2 layers156.5 × 67.5 mm

NixieScanDisplay
profdc9/NixieClock
A Nixie clock that uses IN-14 tubes and very generic components that can be easily sourced.
106 parts10 - 2 layers67.3 × 74.5 mm

- 2 layers144.1 × 181.4 mm

Quadulator
GlobalSequence/quadulator
Quadulator - A quad LFO/ADSR envelope generator for Eurorack synthesizers
128 parts6 - 2 layers97.8 × 109.7 mm

Controller board
Tai-Min/Azure-Sphere-Home-Process-Controller
Industrial like PID coontroller with IoT functionality. Grand Prize winner in Home Is Where the Hack Is Challenge, with Avnet Azure Sphere
50 parts5MIT - 2 layers99.1 × 99.1 mm

At90s2323
atoomnetmarc/AVR-demo-board
AVR demo boards for old AT90S* microcontrollers.
171 parts4Apache-2.0
Questions
How big is the NanoGris PCB?
It measures 164.6 × 108 mm and has 2 copper layers, 1.6 mm thick.
What parts does the NanoGris use?
112 parts, built around the 74HC595 and L7805. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the NanoGris KiCad files?
From the Quinienl/NanoGris repository on GitHub, at the commit this page was made from: the board is NanoGris.kicad_pcb and its schematic NanoGris.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the NanoGris design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).