

Unibone.unrouted
"UniBone" connects a BeagleBone Black micro Linux system to ancient DEC UNIBUS, "QBone" does the same for DEC QBUS.
- Size
- 265.6 × 214.1 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 1,317
- Nets
- 435
- Pads
- 2,757
- Tracks, vias
- 800, 120
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 28 Jul 2026
- Updated
- 8 Sep 2026
Overview
Unibone.unrouted is an open-source printed circuit board by QUniBone, from the QUniBone/QUniBoneClassic repository on GitHub, published under the BSD-2-Clause licence. It is a 4-layer board of 265.6 × 214.1 mm with 1,317 parts on 435 nets, routed with 800 tracks and 120 vias.
It is built around the AM26S10DC, MAX232N and 74HCT377D, with the 24LC256-I/P, 74AHC138D and MMBT3904 among its other parts. Its parts include 59 resistors, 52 ICs, 44 capacitors, 40 connectors and 7 diodes.
Main components
8AM26S10DC
CDIP-160℃~+70℃ 1 15ns@5V,50pF 1mA 20mA 4 4.75V~5.25V Am26S Open-drain Output enable、Short-Circuit Protection Unidirectional CDIP-16 Buffers, Drivers, Receivers, TransceiversAMDBuffers, Drivers, Receivers, TransceiversMAX232N
PDIP-160℃~+70℃ 120Kbps 2 2 4.5V~5.5V Transceiver PDIP-16 RS232 ICs ROHSTexas InstrumentsRS232 ICs74HCT377D
SO-20-300mil-40℃~+125℃ 1 2ns 3.5pF 32ns@4.5V,50pF 4.5V~5.5V 4mA 4ns 5.2mA 53MHz 74HCT Series 8 8uA D-Type Enable Rising Edge Synchronous SO-20-300mil Flip Flops ROHSNexperiaFlip Flops24LC256-I/P
PDIP-8-40℃~+85℃ 1,000,000 cycles 2.5V~5.5V 200 Years 256Kbit 400kHz 5ms Hardware write protection function、Noise suppression function I2C PDIP-8 EEPROM ROHSMicrochip TechnologyEEPROM74AHC138D
SO-16-40℃~+125℃ 2V~5.5V 4uA 6.3ns@5V,50pF 74AHC 8mA 8mA Decoder Single Supply SO-16 Signal Switches, Multiplexers, Decoders ROHSNexperiaSignal Switches / Encoders & Decoders / MultiplexersMMBT3904
SOT-23-55℃~+150℃ 1 NPN 100 100nA 200mA 200mW 300MHz 300mV 40V 6V NPN SOT-23 Bipolar (BJT) ROHSJiangsu Changjing Electronics Technology (CJ)Bipolar (BJT)1N4148WS
SOD-3231.25V@150mA 100V 150mA 1uA@75V 200mW 2A 4ns Independent SOD-323 Switching Diodes ROHSJiangsu Changjing Electronics Technology (CJ)Switching DiodesHFD3
TH-6PTH-6P Signal Relays ROHSHFSignal Relays
README
README.mdQUniBone
This is the software for both Linux-to-UNIBUS bridge "UniBone" and Linux-to-QBUS bridge "QBone"
"UniBone" connects a BeagleBone Black micro Linux system to ancient DEC UNIBUS, "QBone" does the same for DEC QBUS.
UniBone/QBone can keep old PDP-11s running, by emulating devices and aiding in repair.
As UNIBUS and QBUS are quite similar, only one software project compiles for both devices.
In-source differentiation is done via "#define UNIBUS" or "#define QBUS". Source files special to only one bus are marked with suffix "_u" respective "_q".
See project pages at retrocmp.com for UniBone and for QBone
Parts
1,317| Qty | Value | Footprint | References |
|---|---|---|---|
| 1080 | jh:Lochraster_Square_breit | _191105121140_0, _191105121140_1, _191105121140_10, _191105121140_100, _191105121140_101, _191105121140_1000, _191105121140_1001, _191105121140_1002, _191105121140_1004, _191105121140_1005, _191105121140_1006, _191105121140_1007, _191105121140_1008, _191105121140_1009, _191105121140_1010, _191105121140_1011 +1064 | |
| 35 | 100nF | Capacitor_SMD:C_0805_2012Metric | C1, C2, C10, C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23 +19 |
| 16 | AM26S10 | Package_DIP:DIP-16_W7.62mm | U107, U108, U111, U112, U115, U116, U119, U120, U123, U124, U127, U128, U131, U132, U135, U136 |
| 16 | DS8641-LR | Package_DIP:DIP-16_W7.62mm | U7, U8, U11, U12, U15, U16, U19, U20, U23, U24, U27, U28, U31, U32, U35, U36 |
| 13 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R1, R3, R8, R9, R17, R25, R26, R27, R28, R29, R30, R31, R32 |
| 8 | 10 | Resistor_SMD:R_0805_2012Metric | R52, R53, R54, R55, R56, R57, R58, R59 |
| 8 | 15 | Resistor_SMD:R_0805_2012Metric | R40, R41, R42, R43, R44, R45, R46, R47 |
| 8 | 74HCT377 | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U5, U10, U14, U18, U22, U26, U30, U34 |
| 8 | 74LVTH541_PWR | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U4, U9, U13, U17, U21, U25, U29, U33 |
| 6 | 10K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R2, R33, R34, R35, R37, R39 |
| 5 | 22K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R10, R11, R12, R13, R16 |
| 4 | 0 | Resistor_SMD:R_0805_2012Metric | R48, R49, R50, R51 |
| 4 | 1uF | Capacitor_SMD:C_0805_2012Metric | C40, C41, C42, C43 |
| 4 | 6.3uF | Capacitor_THT:CP_Axial_L11.0mm_D6.0mm_P18.00mm_Horizontal | C36, C37, C38, C39 |
| 4 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J41, J42, J61, J62 |
| 4 | MountingHole_3.2mm_M3 | MountingHole:MountingHole_3.2mm_M3 | HOLE1, HOLE2, HOLE3, HOLE4 |
| 4 | NPTH | mals-library-pcb:HOLE-3MM | H1, H2, H7, H8 |
| 3 | 220 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R18, R19, R20 |
| 3 | 470 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4, R5, R14 |
| 3 | GND | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J23, J56, J57 |
| 2 | +3.3V | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4, J34 |
| 2 | +5V UB | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3, J35 |
| 2 | 10 | Resistor_THT:R_Array_SIP8 | RN6, RN7 |
| 2 | 15 | Resistor_THT:R_Array_SIP8 | RN8, RN9 |
| 2 | 180 | Resistor_THT:R_Array_SIP6 | RN3, RN12 |
| 2 | 2K2 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R21, R22 |
| 2 | 3K3 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R23, R24 |
| 2 | BTN | Button_Switch_THT:SW_Tactile_SPST_Angled_PTS645Vx58-2LFS | SW2, SW3 |
| 2 | DEC Handle | jh:DEC-Handle | DECHANDLE1, DECHANDLE2 |
| 2 | Fiducial | jh:Fiducial | F1, F2 |
| 2 | GND | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J13, J14 |
| 2 | GND | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J5, J36 |
| 2 | MMBT3904 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | n.a. | Resistor_THT:R_Array_SIP9 | RN4, RN5 |
| 2 | none | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R7 |
| 2 | opt. | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R36, R38 |
| 1 | - | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J38 |
| 1 | 0 | Resistor_THT:R_Array_SIP8 | RN10 |
| 1 | 1N4148WS | Diode_SMD:D_SOD-323 | D7 |
| 1 | 24LC256 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | 390 | Resistor_THT:R_Array_SIP6 | RN11 |
| 1 | 470uF | Capacitor_THT:CP_Axial_L18.0mm_D8.0mm_P25.00mm_Horizontal | C44 |
| 1 | 4K7 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 1 | 74AHC138 | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U2 |
| 1 | 74LS244_5V | Package_DIP:DIP-20_W7.62mm | U6 |
| 1 | A0 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1 |
| 1 | A1 | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP2 |
| 1 | BBB-P8 | Connector_PinHeader_2.54mm:PinHeader_2x23_P2.54mm_Vertical | J1 |
| 1 | BBB-P9 | Connector_PinHeader_2.54mm:PinHeader_2x23_P2.54mm_Vertical | J2 |
| 1 | CONN-DEC-QUAD-CDEF | jh:dec-conn-quad-ht-pins-only_CDEF | J16 |
| 1 | Conn_01x01 | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J40 |
| 1 | GPIO1_16-19 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J11 |
| 1 | GPIO2_1-5 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J37 |
| 1 | HFD3 | jh:HFD3-relay | K1 |
| 1 | I2C2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J59 |
| 1 | LED0 | LED_THT:LED_D3.0mm_Horizontal_O3.81mm_Z2.0mm | D2 |
| 1 | LED1 | LED_THT:LED_D3.0mm_Horizontal_O3.81mm_Z2.0mm | D3 |
| 1 | LED2 | LED_THT:LED_D3.0mm_Horizontal_O3.81mm_Z2.0mm | D4 |
| 1 | LED3 | LED_THT:LED_D3.0mm_Horizontal_O3.81mm_Z2.0mm | D5 |
| 1 | LTC_IN | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J46 |
| 1 | LTC_OUT | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | MAX232 | Package_DIP:DIP-16_W7.62mm | U37 |
| 1 | ONBUS | LED_THT:LED_D3.0mm_Horizontal_O3.81mm_Z2.0mm | D6 |
| 1 | PRU_CONTROL | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J15 |
| 1 | PWR | LED_THT:LED_D3.0mm_Horizontal_O3.81mm_Z2.0mm | D1 |
| 1 | Panel | Connector_IDC:IDC-Header_2x05_P2.54mm_Horizontal | J7 |
| 1 | Panel_I2C | Connector_IDC:IDC-Header_2x07_P2.54mm_Horizontal | J43 |
| 1 | REG_DATA_FROM_PRU0 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J10 |
| 1 | REG_DATA_TO_PRU1 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J17 |
| 1 | Reichelt AKL 059-6 | TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-6-3.5-H_1x06_P3.50mm_Horizontal | J60 |
| 1 | SW0-3 | Button_Switch_THT:SW_DIP_SPSTx04_Piano_CTS_Series194-4MSTN_W7.62mm_P2.54mm | SW1 |
| 1 | UART1_RS232_Schneid-Klemm_2x5 | Connector_IDC:IDC-Header_2x05_P2.54mm_Horizontal | J27 |
| 1 | UART2_RS232_Schneid-Klemm_2x5 | Connector_IDC:IDC-Header_2x05_P2.54mm_Horizontal | J33 |
| 1 | UB_ADDR | Connector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_Vertical | J21 |
| 1 | UB_BRG4 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J28 |
| 1 | UB_BRG5 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J29 |
| 1 | UB_BRG6 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J30 |
| 1 | UB_BRG7 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J31 |
| 1 | UB_C01 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J22 |
| 1 | UB_DATA | Connector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_Vertical | J19 |
The 1,312 most common of 1,317 parts.
Similar boards
- 2 layers82.6 × 58.4 mm

- 2 layers235 × 158.8 mm

Gigatron
flypie/Gigatron
This is a version of the files from https://gigatron.io/ altered to work on a vanilla KiCAD 5.1.6. Changes are minimal in the schematic and PCB, layout has only been changed where dimensions or orientations changed as a…
151 parts2 - 2 layers99.1 × 87.6 mm

- 2 layers102 × 96 mm

- 4 layers200 × 50 mm

- 4 layers280 × 140 mm

P8x alu card
ksr/p8x
Generated by generators/genkicad.py from the canonical geneagle netlist (CARDS["peripheral-card"]), same standard as the memory card: 4-layer (F/B signals, In1=GND, In2=VCC planes), a bypass cap above each IC, a…
77 parts - 2 layers284.9 × 96.5 mm

- 4 layers306 × 244 mm

Questions
How big is the Unibone.unrouted PCB?
It measures 265.6 × 214.1 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Unibone.unrouted use?
1,317 parts, built around the AM26S10DC, MAX232N, 74HCT377D and 24LC256-I/P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Unibone.unrouted KiCad files?
From the QUniBone/QUniBoneClassic repository on GitHub, at the commit this page was made from: the board is 01.01_pcb/unibone/unibone.unrouted.kicad_pcb and its schematic 01.01_pcb/unibone/DS8641.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Unibone.unrouted design in my own project?
Its repository publishes it under the BSD-2-Clause licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).