

ESP32 Breakouts Playground
Various PCB projects, mostly in KiCad
- Size
- 203.1 × 108.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 117
- Nets
- 121
- Pads
- 404
- Tracks, vias
- 1,016, 53
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 27 May 2023
- Updated
- 8 May 2026
Overview
ESP32 Breakouts Playground is an open-source printed circuit board by PockyBum522, from the PockyBum522/cad-pcb-projects repository on GitHub, published under the MIT licence. It is a 2-layer board of 203.1 × 108.1 mm with 117 parts on 121 nets, routed with 1,016 tracks and 53 vias.
It is built around the ESP32-S3-WROOM-1-N8, AP63203WU and FT230XS-R, with the LAN8720A-CP and USB4105-GF-A among its other parts. Its parts include 27 connectors, 16 capacitors, 8 resistors, 5 ICs and 2 switches. It belongs with the interfaces and adapters boards and the ESP32 boards of this library.
Main components
5ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesAP63203WU
TSOT-23-6-40℃~+85℃@(TA) 1 1.1MHz 22uA 2A 3.3V 3.8V~32V Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Cycle-by-cycle current limiting、Hiccup current limiting、EMI optimization (spread spectrum) Step-down type Yes TSOT-23-6 DC-DC Converters ROHSDiodes IncorporatedDC-DC ConvertersFT230XS-R
SSOP-16-150mil-40℃~+85℃ 125uA 3.3V~5V 8mA USB 2.0 USB to UART SSOP-16-150mil USB Converters ROHSFTDIUSB ConvertersLAN8720A-CP
QFN-24-EP(4x4)Ethernet ICsMicrochip TechnologyUSB4105-GF-A
SMD-40℃~+85℃ 1 12P 48V 5A Black Female Surface Mount, Right Angle Type-C USB 2.0 SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB Connectors
README
README.mdcad-pcb-projects
Various PCB projects, mostly in KiCAD
WT32-ETH01 Programming Shield
ESP32-DevKitC-1 Prototype Shield


Parts
117| Qty | Value | Footprint | References |
|---|---|---|---|
| 57 | TestPoint | David-Footprints:KOA_RCWCTE_TEST_POINT | TP1, TP2, TP10, TP11, TP12, TP13, TP14, TP15, TP16, TP17, TP18, TP19, TP20, TP21, TP22, TP23 +41 |
| 10 | Conn_01x02_Socket | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J1, J2, J3, J4, J5, J8, J13, J19, J20, J23 |
| 6 | 100nF | Capacitor_SMD:C_1206_3216Metric | C3, C5, C6, C8, C12, C13 |
| 5 | Conn_01x06_Socket | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J6, J15, J21, J24, J25 |
| 3 | 0R | Resistor_SMD:R_2010_5025Metric_Pad1.40x2.65mm_HandSolder | R1, R2, R3 |
| 3 | 1uF | Capacitor_SMD:C_1206_3216Metric | C7, C9, C14 |
| 3 | 22uF | Capacitor_SMD:C_1206_3216Metric | C2, C4, C15 |
| 3 | Conn_01x03_Socket | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J10, J11, J18 |
| 2 | 1K5 | Resistor_SMD:R_0603_1608Metric | R7, R8 |
| 2 | 47uF | Capacitor_SMD:CP_Elec_5x5.3 | C1, C16 |
| 2 | 5.1K | Resistor_SMD:R_0603_1608Metric | R5, R6 |
| 2 | Conn_01x05_Socket | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J16, J22 |
| 2 | Conn_01x11_Socket | Connector_PinHeader_2.54mm:PinHeader_1x11_P2.54mm_Vertical | J7, J12 |
| 1 | 10nF | Capacitor_SMD:C_1206_3216Metric | C10 |
| 1 | 10uH | Inductor_SMD:L_Taiyo-Yuden_NR-60xx | L1 |
| 1 | 22nF | Capacitor_SMD:C_1206_3216Metric | C11 |
| 1 | 430R | Resistor_SMD:R_0603_1608Metric | R4 |
| 1 | AP63203WU | Package_TO_SOT_SMD:TSOT-23-6 | U1 |
| 1 | Conn_01x04_Socket | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J26 |
| 1 | Conn_01x12_Socket | Connector_PinHeader_2.54mm:PinHeader_1x12_P2.54mm_Vertical | J9 |
| 1 | ESP32-S3-WROOM-1 | David-Footprints:ESP32-S3-wrooom | U3 |
| 1 | FT230XS-R | DigiKey Footprints:SOIC-16_W3.90mm | U2 |
| 1 | FerriteBead_Small | Inductor_SMD:L_0603_1608Metric | FB1 |
| 1 | LAN8720A | David-Footprints:VQFN-24-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U5 |
| 1 | MAX31865xAP | Package_SO:SSOP-20_5.3x7.2mm_P0.65mm | U4 |
| 1 | RJ45_Amphenol_RJMG1BD3B8K1ANR | Connector_RJ:RJ45_Amphenol_RJMG1BD3B8K1ANR | J27 |
| 1 | SW_BOOT | Button_Switch_SMD:SW_SPST_EVPBF | SW2 |
| 1 | SW_RST | Button_Switch_SMD:SW_SPST_EVPBF | SW1 |
| 1 | Screw_Terminal_01x04 | TerminalBlock_RND:TerminalBlock_RND_205-00069_1x04_P7.50mm_Horizontal | J14 |
| 1 | USB4105-GF-A | David-Footprints:GCT_USB4105-GF-A | J17 |
More from PockyBum522/cad-pcb-projects
2- 2 layers50.8 × 98.3 mm

- 2 layers133.1 × 119.9 mm

Similar boards
- 4 layers67 × 42 mm

Sonar Controller
haydenmc/McAfee-Farm-Sonar-Controller
An ESP32 project that uses a sonar depth sensor to measure the water level of a cistern tank.
59 parts - 4 layers102.6 × 107.3 mm

- 4 layers46.8 × 72.5 mm

Fiddler
ausocean/rig
Repository for AusOcean CAD files, PCB design files, 3D models and 3D modeling scripts.
124 parts - 4 layers100 × 100 mm

Hw alpha
Yexall/CPE-450.Capstone
Fall 24 - Winter 25 Cal Poly Capstone project by Haas Hooligans. This projects aims to build a machine monitoring system for the Cal Poly IME department.
171 parts - 4 layers180 × 110 mm

PETER
dennowiggle/Retro-PETER
3.3V Retro computer project => FPGA + RCBUS + CPU boards making a custom system.
419 parts4LGPL-2.1 - 4 layers55 × 100.5 mm

OSS Radio Hardware Design
Arkos-Engineering/HT-15_hardware
We can split this out into separate repos later, right now its very convenient to have everything here.
256 parts72 - 4 layers119.4 × 119.4 mm

- 2 layers194.1 × 141.7 mm

Questions
How big is the ESP32 Breakouts Playground PCB?
It measures 203.1 × 108.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP32 Breakouts Playground use?
117 parts, built around the ESP32-S3-WROOM-1-N8, AP63203WU, FT230XS-R and LAN8720A-CP. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32 Breakouts Playground KiCad files?
From the PockyBum522/cad-pcb-projects repository on GitHub, at the commit this page was made from: the board is Playgrounds/ESP32 Breakouts Playground/ESP32 Breakouts Playground.kicad_pcb and its schematic ESP32-S3-DevKitC-1/Car NFC Reader Main Board/Car NFC Main Board/Car NFC Main Board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32 Breakouts Playground design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).