Skip to the content
2 layers59.5 × 25.3 mmIMUMaster, the printed circuit board in 3D
Size
59.5 × 25.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
58
Nets
45
Pads
188
Tracks, vias
241, 33
Pours
4
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
6 Oct 2026
Updated
6 Oct 2026

Overview

IMUMaster is an open-source printed circuit board by Pledoge, from the Pledoge/IMU-ESPC3-Board repository on GitHub. It is a 2-layer board of 59.5 × 25.3 mm with 58 parts on 45 nets, routed with 241 tracks and 33 vias.

It is built around the ESP32-C3-WROOM-02-H4, SY8120B and ICM-42688-P, with the AO3400A, K34 and MLT-9032 among its other parts. Its parts include 21 resistors, 17 capacitors, 4 diodes, 3 ICs and 2 transistors. It belongs with the ESP32 and RISC-V boards of this library.

Main components

7

README

README.md

IMUMaster-PCB

Project Overview

IMUMaster is a hardware circuit board project based on the ICM-42688-P (a high-precision 6-axis motion tracking/Inertial Measurement Unit). The schematic and PCB layout for this project are designed using KiCad 9.0 (and above). The board is equipped with an ESP32-C3-WROOM-02 module for processing and communication, an SY8120B high-efficiency synchronous buck converter to provide stable power, and integrates an MLT-9032 SMD buzzer for status indications or alarms. Power and programming can be achieved via the onboard USB-C receptacle or the JST single-row connector.

Key Components

  • MCU/Wireless Module: ESP32-C3-WROOM-02 (Espressif) - Provides Wi-Fi & Bluetooth LE connectivity and acts as the main controller.
  • IMU Sensor: ICM-42688-P (TDK InvenSense) - 6-axis motion tracking device (3-axis gyroscope + 3-axis accelerometer).
  • Power Management: SY8120B (Silergy) - High-efficiency 2A, 18V input synchronous step-down regulator.
  • Audio Feedback: MLT-9032 - SMD passive/active buzzer.
  • Connectors: 16-pin USB Type-C receptacle, JST XH 2.50mm 1x02 for external power input.

Pin Configurations

Depending on the schematic routing, the key pinouts and interfaces are typically summarized as follows:

  • IMU (ICM-42688-P) Interface: Connects to the ESP32-C3 via the SPI or I2C bus (Check the schematic for exact SCL/SCLK, SDA/SDI, SDO, CS pin mappings).
  • Buzzer (MLT-9032): Driven by an ESP32-C3 GPIO via a PWM signal to generate tones.
  • USB-C (16-Pin): Used for VBUS (Power input) and D+/D- for USB Serial / JTAG flashing for the ESP32-C3.
  • JST-XH (1x02): Used for external power supply input (e.g. Battery VCC and GND).

Directory Structure

  • IMUMaster.kicad_sch / .kicad_pcb: Core KiCad schematic and PCB design files. (Requires KiCad 9.0 or later)
  • kicad_api_libs/: Contains project-specific component symbols (.kicad_sym), footprints (.pretty/.kicad_mod), and 3D models.
  • bom/: Contains the interactive BOM file (ibom.html), which is highly recommended for manual soldering and debugging.
  • production/: Manufacturing & fabrication files ready to be sent to PCBA manufacturers (like JLCPCB), including the production BOM (bom.csv) and component placement coordinates (positions.csv).

Fabrication and PCBA Instructions

All necessary files for fabrication and PCB Assembly (PCBA) are located in the production/ directory. You can directly use the provided Bill of Materials (BOM) and CPL/POS data for manufacturing submission.

Local Viewing and Editing

  1. Please install KiCad EDA version 9.0 or newer.
  2. Double-click the IMUMaster.kicad_pro file to open the entire project, schematic, and PCB layout.
  3. Open bom/ibom.html in your web browser to preview the Interactive BOM, which clearly highlights the exact position of each component on the PCB.

IMU-ESPC3-Board

Parts

58
QtyValueFootprintReferences
710kResistor_SMD:R_0603_1608MetricR3, R4, R7, R12, R13, R15, R54
4100nCapacitor_SMD:C_0603_1608MetricC7, C8, C10, C11
4MountingHole_PadMountingHole:MountingHole_3.2mm_M3_DIN965_PadH1, H2, H3, H4
322uCapacitor_SMD:C_1206_3216MetricC14, C16, C18
322uFCapacitor_SMD:C_1206_3216MetricC2, C25, C26
20Resistor_SMD:R_0603_1608MetricR1, R2
20.01uFCapacitor_SMD:C_0603_1608MetricC15, C27
21kResistor_SMD:R_0603_1608MetricR8, R52
222Resistor_SMD:R_0603_1608MetricR5, R6
25.1kResistor_SMD:R_0603_1608MetricR21, R22
2AO3400APackage_TO_SOT_SMD:SOT-23Q1, Q4
2SW_PushButton_Switch_SMD:SW_SPST_B3U-1000PSW1, SW14
1(36R)Resistor_SMD:R_1206_3216MetricR62
10.1uFCapacitor_SMD:C_0603_1608MetricC1
1100kResistor_SMD:R_0603_1608MetricR10
1100nFCapacitor_SMD:C_0603_1608MetricC6
110uCapacitor_SMD:C_0603_1608MetricC4
110uInductor_SMD:L_Vishay_IHLP-2020L3
1120RResistor_SMD:R_0603_1608MetricR14
11A 1206Fuse:Fuse_1206_3216MetricF1
11uFCapacitor_SMD:C_0603_1608MetricC3
120pCapacitor_SMD:C_0603_1608MetricC23
122.1kResistor_SMD:R_0603_1608MetricR11
12k2Resistor_SMD:R_0603_1608MetricR51
133RResistor_SMD:R_0603_1608MetricR57
1Conn_01x02_PinConnector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_VerticalJ1
1ESP32-C3-WROOM-02RF_Module:ESP32-C3-WROOM-02U1
1GreenLED_SMD:LED_0603_1608MetricD23
1ICM-42688-Pkicad_api_lib:ICM-42688-PU2
1K34Diode_SMD:D_SMFD7
1MLT-9032kicad_api_lib:MLT-9032BUZZER1
1SS34Diode_SMD:D_SMAD1
1SY8120Bkicad_api_lib:SY8120BU4
1USB_C_Receptacle_USB2.0_16PConnector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_HorizontalJ2
1YellowLED_SMD:LED_0603_1608MetricD22

Similar boards

  • 6 layers84.5 × 56 mmVLF4 PCB, the printed circuit board in 3D

    VLF4 PCB

    McMaster-Rocketry-Team/VLF4r2

    PCB schematics and layout for Void Lake Fusion 4 Avionics

    156 parts3
  • 2 layers105.4 × 86.5 mmGood Boy Limiter, the printed circuit board in 3D

    Good Boy Limiter

    JohnanLuca02/BYTE_Electronics

    Repository for everything concerning the electronics (PCB, Electrical schemes, BOM, ...) of the robot dog project of the AiTeam called BYTE.

    111 parts1
  • 4 layers80 × 50 mmMianCtrl H7, the printed circuit board in 3D

    MianCtrl H7

    Aiyin4Da-2/Main_Ctrl_H7

    STM32H723VGT6 MainCtrlBoard Author: Aiyin4DaGLD · Hardware: v1.2 · Updated: 2026-08-21

    153 partsMIT
  • 4 layers38 × 74 mmStratosdrone, the printed circuit board in 3D

    Stratosdrone

    equationstratos/STRATOSDRONES

    A 4-layer, 36×70 mm Tello-style portrait controller board for the STRATOSDRONE: chip-down ESP32-P4 (flight + camera + hardware H.264) with an ESP32-C6-MINI-1 Wi-Fi co-processor, IMU / barometer / ToF / optical-flow…

    115 parts
  • 4 layers91.9 × 91.9 mmPursuit, the printed circuit board in 3D

    Pursuit

    Pai-88/pursuit-drone

    92 mm person-following quadcopter whose 4-layer PCB is its own airframe: ESP32-S3 flight firmware, off-board face and body re-identification, generated wire protocol. Bench-tested, not yet flown.

    58 parts
  • 4 layers80 × 80 mmUnderwaterCom, the printed circuit board in 3D

    UnderwaterCom

    Frrrrrrrrrank/Underwater-Communication

    212 parts
  • 4 layers63.7 × 64 mmWirelessCharger V0.1, the printed circuit board in 3D

    WirelessCharger V0.1

    htsong-lab/hardware

    Hardware engineering portfolio: FPGA high-speed board, RoboMaster power electronics and smart-car projects.

    196 parts

Questions

How big is the IMUMaster PCB?

It measures 59.5 × 25.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the IMUMaster use?

58 parts, built around the ESP32-C3-WROOM-02-H4, SY8120B, ICM-42688-P and AO3400A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the IMUMaster KiCad files?

From the Pledoge/IMU-ESPC3-Board repository on GitHub, at the commit this page was made from: the board is IMUMaster.kicad_pcb and its schematic IMUMaster.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the IMUMaster design in my own project?

Its repository states no licence, so its author keeps all rights: ask Pledoge before reusing the design.