

Recent IMU
Inertial measurement unit project
- Size
- 89 × 35.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 58
- Nets
- 75
- Pads
- 301
- Tracks, vias
- 544, 75
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 1 Aug 2024
- Updated
- 1 Aug 2024
Overview
Recent IMU is an open-source printed circuit board by Ndambia-007, from the Ndambia-007/IMU repository on GitHub. It is a 2-layer board of 89 × 35.9 mm with 58 parts on 75 nets, routed with 544 tracks and 75 vias.
It is built around the CH340C, ICM-42688-P and IFX25401TBV, with the MPU-6050, BC847 and SP0502BAHTG among its other parts. Its parts include 15 resistors, 13 capacitors, 10 diodes, 5 ICs and 4 transistors. It belongs with the sensors and measurement boards and the ESP32 and RISC-V boards of this library.
Main components
8CH340C
SOP-16-20℃~+70℃ 2Mbps 3.3V、5V 50uA 7mA Transceiver USB 2.0 SOP-16 USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersICM-42688-P
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 2KB 7.5uA IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps Motion Event Detection, Synchronization, Timestamp Support LGA-14(2.5x3) Accelerometers ROHSTDK InvenSenseAccelerometersIFX25401TBV
TO-263-5-40℃~+125℃@(Tj) 1 2.5V~20V 220uA 400mA 40V 500mV@(250mA) 54dB@(100Hz) Adjustable Over Current Protection、Over Temperature Protection、Reverse connection protection、Enable Positive TO-263-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSInfineon TechnologiesVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMPU-6050
QFN-24-EP(4x4)-40℃~+85℃ 16bit 1KB 2.375V~3.46V 5uA Accelerometer Gyroscope I2C X,Y,Z X,Y,Z ±16g ±2000dps QFN-24-EP(4x4) Accelerometers ROHSTDK InvenSenseAccelerometersBC847
SOT-231 NPN 100MHz 100mA 100nA 110 200mW 45V 500mV 6V NPN SOT-23 Bipolar (BJT) ROHSShikuesBipolar (BJT)SP0502BAHTG
SOT-23-40℃~+125℃ 100nA 2 30pF 5.5V 8.5V IEC 61000-4-2 TVS Unidirectional SOT-23 ESD and Surge Protection (TVS/ESD) ROHSLittelfuseESD And Surge Protection (TVS/ESD)CD4148WP
1206-55℃~+150℃ 1 Independent 1.25V@100mA 150mA 1A 400mW 4ns 5uA@75V 75V 1206 Switching Diodes ROHSLIZSwitching DiodesTS02-66-95-BK-260-LCR-D
插件-30℃~+80℃ 12V 2.6N 50mA 60,000 Cycles PC Pin Round Button SPST Through Hole 插件 Tactile Switches ROHSCUITactile Switches
Parts
58| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 0.1uF | Capacitor_SMD:C_01005_0402Metric | C2, C3, C5, C6, C8, C9 |
| 5 | 10k | Resistor_SMD:R_0201_0603Metric | R3, R9, R11, R12, R15 |
| 5 | 4.7k | Resistor_SMD:R_0201_0603Metric | R1, R2, R6, R7, R10 |
| 4 | BC847 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3, Q4 |
| 3 | D_Schottky | Schottky:DIO_MMSZ4700T1G | D5, D6, D7 |
| 3 | TX | TestPoint:TestPoint_Pad_D1.0mm | +5v, TP2, TP6 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C10, C12 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | 1k | Resistor_SMD:R_0201_0603Metric | R13, R14 |
| 2 | SP0502BAHT | Package_TO_SOT_SMD:SOT-23 | D3, D4 |
| 1 | 0.1uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C13 |
| 1 | 1000uF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C11 |
| 1 | 10nF | Capacitor_SMD:C_01005_0402Metric | C7 |
| 1 | 10uF | Capacitor_SMD:C_01005_0402Metric | C1 |
| 1 | 13.19k | Resistor_SMD:R_0201_0603Metric | R8 |
| 1 | 2.2nF | Capacitor_SMD:C_01005_0402Metric | C4 |
| 1 | CD4148W | Diode_SMD:D_0805_2012Metric | D10 |
| 1 | CH340C | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U6 |
| 1 | Conn_01x04_Pin | Connector_PinHeader_1.00mm:PinHeader_1x04_P1.00mm_Vertical | J1 |
| 1 | ESP32-PICO-MINI-02 | esp 32:MODULE_ESP32-PICO-MINI-02 | U1 |
| 1 | ICM-42688-P | ICM:PQFN50P300X250X97-14N | U3 |
| 1 | IFX25401TBV | Package_TO_SOT_SMD:TO-263-5_TabPin3 | U4 |
| 1 | MPU-6050 | mpu:QFN50P400X400X95-24N | U2 |
| 1 | RX | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D9 |
| 1 | RX | TestPoint:TestPoint_Pad_D1.0mm | RX |
| 1 | Red Led | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | Relay_SPDT | Relay_THT:Relay_SPDT_Finder_32.21-x000 | K1 |
| 1 | SCL | TestPoint:TestPoint_Pad_D1.0mm | SCL |
| 1 | SDA | TestPoint:TestPoint_Pad_D1.0mm | SDA |
| 1 | Screw_Terminal_01x03 | Screw:CUI_TB009-508-03BE | J4 |
| 1 | Status Led | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | TS02-66-95-BK-260-LCR-D | button:SW_TS02-66-95-BK-260-LCR-D | S1 |
| 1 | TX | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D8 |
| 1 | USB_C_Receptacle_USB2.0 | Connector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J2 |
Similar boards
- 2 layers67.5 × 32 mm

- 4 layers30.2 × 68.6 mm

Esp32
skkgokul/4-layer--PCB-Design-esp32--mini-board
ESP 32 mini is a type of microcontroller which is uesd to control the IOT devices and for various projectes
26 parts - 2 layers25.4 × 25.4 mm

PIC Timer
cnkurzke/HelloPIC_Interrupts
Sample code for the PIC 12F1572 interrupt handling
25 partsBSD-2-Clause - 2 layers80 × 50 mm

- 2 layers150 × 100 mm

SmartCube
kokhaie/Smart-Refrigerator-Demo
The KiCad-generated BOM is mirrored into the documentation site under docs/ so it can be published through GitHub Pages.
91 parts - 2 layers68.6 × 53.3 mm

- 2 layers100 × 100 mm

Internship
neilgibsonpinto-art/litewing-65-flight-controller
An ultra-low SWaP-C (Size, Weight, Power, and Cost) monolithic flight computer and decentralized micro-UAV swarm reconnaissance architecture engineered by Neil Gibson Pinto at Sahyadri College of Engineering &…
87 parts - 4 layers48.9 × 49.8 mm

FC REV2
xXsenseiXx/KHATAF-F411
Open-hardware 4-layer STM32F411 drone flight controller designed in KiCad for INAV and Betaflight.
73 parts2
Questions
How big is the Recent IMU PCB?
It measures 89 × 35.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Recent IMU use?
58 parts, built around the CH340C, ICM-42688-P, IFX25401TBV and MPU-6050. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Recent IMU KiCad files?
From the Ndambia-007/IMU repository on GitHub, at the commit this page was made from: the board is Recent IMU.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Recent IMU design in my own project?
Its repository states no licence, so its author keeps all rights: ask Ndambia-007 before reusing the design.