Skip to the content
2 layers70 × 20.2 mmPCF8575-HD44780, the printed circuit board in 3D

8 bit I2C using PCF8575 and custom interface board to drive HD44780 LCD hardware, code driver for STM32 "BlackPill" board

Size
70 × 20.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
17
Nets
30
Pads
100
Tracks, vias
324, 12
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
7 Jul 2026
Updated
18 Jul 2026

Overview

PCF8575-HD44780 is an open-source printed circuit board by MrCrusty, from the MrCrusty/PCF8575-HD44780 repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board of 70 × 20.2 mm with 17 parts on 30 nets, routed with 324 tracks and 12 vias.

It is built around the BC847. Its parts include 7 resistors, 5 connectors, 2 capacitors, 1 IC and 1 transistor. It belongs with the retro computing and games and lEDs and displays boards of this library.

Main components

1

README

README.md

PCF8575-HD44780

8BIT 12C HD44780

The Kicad 10.x 3D rendered image above shows a PCB designed to use a PCF8575 I2C two port 8bit custom interface for HD44780 LCD's

A C99 Software driver is provided for STM32 "BlackPill" development board, which should be easily modifed for other MCU's

Hitachi brought the HD44780 to market 40 years ago, at that time I was just turning 40 and in that year my employer complained at the exhorbitant cost of using this display in a digital multimeter that could have quite have easily been an off the peg analogue AVO.

Today these LCd's are sub £5.00 for a 4 line by 20 character display. However interfacing this LCD in it's native 8bit data bus mode uses to many I/O pins on an embeded MCU design. The solution has been to use I2C interface modules notably the PCF8574 which has become popular as they only require the MCU to use 2 I/O pins (SDA and SCK) to effect communication between the LCD and the MCU.

image image curtosy of "Cricklewood Electronics"

There is to my knowledge only one 8 Bit I2C interface specifically sold to interface directly with the pins of an HD44780LCD display

There is a lot of excelent code that suports these I2C port extender modules. There is a trade off with using only an 8 bit extender port which is that the display has to be operated in 4 bit bus mode so that the other 4 bits can be used for the displays control lines. Whilst there is a lot of code for writing to a display in 4 bit mode, there is a very limited amount of code to be found for reading the display memory in 4 bit mode.

So is it possible to write to the Hd44780 with I2C in 8 bit mode yes it is not very difficult and a commercial module for doing this is as shown below

image image curtosy of "diymore Alice1101983 Store"

It uses the MCP23017 chip to provide all the control bits and data bits required to run an hd44780 LCD in 8 bit mode. I have written code for it to run on a STM32 "BlackPill" development board. It works, its fast, and it easily reads the memory from the HD44780 bus.

So why design and build my own I2C dual 8 bit port device using the PCF8575 the answer is that the MCP23017 chip needs at least one more I/O pin to be supplied by the MCU in the guise of a reset line, this is essential in my view as the adressing mode of the device can be two diferent options. The other problem for me is that it has far more registers than I need to run the LCD.

Parts

17
QtyValueFootprintReferences
7R_SmallResistor_SMD:R_0805_2012MetricR1, R2, R3, R4, R5, R6, R7
10.1ufCapacitor_SMD:C_0805_2012MetricC2
11ufCapacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolderC1
13362P-1-253LF3362P-1-253LF:TRIM_3362P-1-253LFVR1
1BC847Package_TO_SOT_SMD:SOT-23Q1
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ3
1Conn_01x16_SocketConnector_PinHeader_2.54mm:PinHeader_1x16_P2.54mm_VerticalJ2
1Conn_01x18_SocketConnector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_VerticalJ4
1Conn_02x03_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_VerticalJ1
1Conn_02x05_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x05_P2.54mm_VerticalJ5
1PCF8575DBRPackage_SO:SSOP-24_5.3x8.2mm_P0.65mmU1

Similar boards

  • 2 layers271.8 × 114.3 mmArdumower mega shield svn, the printed circuit board in 3D

    Ardumower mega shield svn

    Ardumower/ardumower

    Develop an open source robotic lawn mower (HW+SW reference platform)

    426 parts282
  • 2 layers130 × 80 mmSmu main 1, the printed circuit board in 3D

    Smu main 1

    jaromir-sukuba/J-SMU

    DIY source-measure unit

    210 parts244
  • 2 layers58 × 110 mmVco core, the printed circuit board in 3D

    Vco core

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    146 parts222
  • 4 layers124.6 × 68.7 mmOssc board, the printed circuit board in 3D

    Ossc board

    marqs85/ossc_pcb

    ossc pcb design files

    265 parts163
  • 2 layers200 × 100 mmPolykit x monosynth, the printed circuit board in 3D

    Polykit x monosynth

    polykit/polykit-x-monosynth

    The Polykit X1 is a DIY semi-modular, analog, patchable synthesizer

    167 parts94
  • 2 layers156.6 × 125.2 mmAutoFeeder, the printed circuit board in 3D

    AutoFeeder

    ErichStyger/McuOpenPnP_Machine

    Repository for the McuOnEclipse OpenPnP machine

    58 parts69
  • 2 layers45.2 × 36.6 mmKaffeeInterface v1, the printed circuit board in 3D

    KaffeeInterface v1

    misteu/RPiCoffee

    Modding / hacking of a coffee machine (DeLonghi ECAM 22.110.B Magnifica S) for IoT capabilities

    50 parts64BSD-3-Clause
  • 4 layers43.8 × 30.2 mmS VHS ZX Spectrum Rev. D, the printed circuit board in 3D

    S VHS ZX Spectrum Rev. D

    redhawk668/ZX-Spectrum-S-Video

    S-Video Modification PCB for the ZX Spectrum

    17 parts47GPL-3.0

Questions

How big is the PCF8575-HD44780 PCB?

It measures 70 × 20.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PCF8575-HD44780 use?

17 parts, built around the BC847. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PCF8575-HD44780 KiCad files?

From the MrCrusty/PCF8575-HD44780 repository on GitHub, at the commit this page was made from: the board is PCF8575_HD44780/PCF8575_HD44780.kicad_pcb and its schematic PCF8575_HD44780/PCF8575_HD44780.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PCF8575-HD44780 design in my own project?

Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).