
JK BMS CAN
dremeier/Arduino-JK-BMS-To-Pylontech-CAN-PCB
PCB and Case for the Arduino JK-BMS To Pylontech CAN converter

To test ESP-Hosted-ng I designed this board to plug into and SD-card slot for easy testing.
Esp32 hosted is an open-source printed circuit board by Mr-Bossman, from the Mr-Bossman/esp_hosted-board repository on GitHub. It is a 2-layer board of 56.5 × 31 mm with 27 parts on 38 nets, routed with 197 tracks and 36 vias.
It is built around the ESP32-WROOM-32 and AP7384-33SA. Its parts include 12 resistors, 7 capacitors, 4 connectors, 3 ICs and 1 switch. It belongs with the ESP32 boards of this library.
To test ESP-Hosted-ng I designed this board to plug into and SD-card slot for easy testing.
The mothod I used before has some major signal integrity loss due to the jumper wires I used.



| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 10k | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | R1, R2, R3, R4, R5, R7, R8, R9, R10, R11, R12 |
| 5 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3, C5, C6, C7 |
| 2 | 10u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C4 |
| 1 | 1k | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | R6 |
| 1 | AP7384-33SA | Package_TO_SOT_SMD:SOT-23 | U1 |
| 1 | BT_UART | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J1 |
| 1 | ESP32-WROOM-32 | RF_Module:ESP32-WROOM-32 | U2 |
| 1 | PCB_SD | sd_card:PCB-SD | U3 |
| 1 | PROG | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J4 |
| 1 | PWR | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J3 |
| 1 | RESET | Button_Switch_THT:SW_PUSH_6mm | SW1 |
| 1 | WIFI | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J2 |

dremeier/Arduino-JK-BMS-To-Pylontech-CAN-PCB
PCB and Case for the Arduino JK-BMS To Pylontech CAN converter



asterics/esp32_mouse_keyboard
ESP32 implementation for HID over GATT Keyboard and Mouse (Bluetooth Low Energy). Including serial API for external modules (similar to Adafruit EZKey HID)


Bellafaire/ESP32-Smart-Watch
An open source smartwatch based on the ESP32 compatible with the Arduino IDE.


It measures 56.5 × 31 mm and has 2 copper layers, 0.8 mm thick.
27 parts, built around the ESP32-WROOM-32 and AP7384-33SA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Mr-Bossman/esp_hosted-board repository on GitHub, at the commit this page was made from: the board is esp32_hosted.kicad_pcb and its schematic esp32_hosted.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Mr-Bossman before reusing the design.