

Driver Control PCB
- Size
- 132.7 × 121.4 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 71
- Pads
- 165
- Tracks, vias
- 201, 16
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 15 Feb 2026
- Updated
- 6 May 2026
Overview
Driver Control PCB is an open-source printed circuit board by Monash-Railway-Express, from the Monash-Railway-Express/KiCad_Files repository on GitHub. It is a 4-layer board of 132.7 × 121.4 mm with 46 parts on 71 nets, routed with 201 tracks and 16 vias.
It is built around the ESP32-S3-DEVKITC-1-N8 and SN65HVD230D. Its parts include 21 resistors, 4 connectors, 2 ICs and 1 capacitor. It belongs with the ESP32 boards of this library.
Main components
2ESP32-S3-DEVKITC-1-N8
-- WiFi Modules ROHSEspressif SystemsWiFi ModulesSN65HVD230D
SOIC-8-40℃~+85℃ 1 17mA 1Mbps 370uA 3V~3.6V CAN Transceiver Low-power mode、Wake-up function、ESD protection、Thermal shutdown protection、Bus fault protection、Hot-swap protection SOIC-8 CAN Transceivers ROHSTexas InstrumentsCAN Transceivers
README
README.mdKiCad-Libraries
To add the footprint library, go to Assign footprints -> Manage footprint libraries -> Add existing library and select the MREx.pretty folder. Alternatively, from the main KiCad project go to Preferences -> Manage footprint libraries -> Add existing library and select the MREx.pretty folder. The library “MREx” will then appear in the footprint library list and you will be able to access its footprints in Assign footprints. When updates are made to the library, pull origin in the cloned repo (clone this repo) and KiCad will use the updated library automatically.
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 10 | 1K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R2, R3, R4, R5, R6, R7, R8, R9, R10, R11 |
| 9 | 10k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1, R12, R13, R14, R15, R16, R18, R19, R20 |
| 4 | , , , | ||
| 4 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | SW_Push1, SW_Push2, SW_Tog1, SW_Tog2 |
| 2 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R17, R21 |
| 2 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Horizontal | R_BRK1, R_THR1 |
| 2 | Conn_01x04_Pin | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Horizontal | R_pos1, R_pos2 |
| 2 | Conn_01x06_Pin | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Horizontal | R_5Pos1, R_5Pos2 |
| 2 | DSUB9_FEMALE_RIGHT-ANGLE-THT_2301844-1_TEC | MREx:DSUB9_FEMALE_RIGHT-ANGLE-THT_2301844-1_TEC | J7, J8 |
| 2 | LOGO | LOGO | MREx, MREx |
| 1 | 0.1uf | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 120 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R_term1 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | Conn_01x03_Pin | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J1 |
| 1 | ESP32-S3-DevKitC | Esp32:ESP32-S3-DevKitC | U1 |
| 1 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP2 |
| 1 | SN65HVD230 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
More from Monash-Railway-Express/KiCad_Files
11- 4 layers64.3 × 97.6 mm

- 4 layers100 × 100 mm

- 2 layers100 × 100 mm

- 2 layers110.2 × 89.6 mm

- 2 layers100 × 100 mm

- 2 layers100 × 91.7 mm

- 2 layers100 × 91.7 mm

- 2 layers79 × 90.9 mm

- 2 layers52 × 100 mm

- 2 layers100 × 100 mm

- 2 layers100 × 100 mm

Similar boards
- 2 layers96.3 × 78.3 mm

Actuation board2
cuspaceflight/Engine-Test-Stand-Instrumentation
Engine test stand for Cambridge University Space Flight
20 parts - 2 layers100 × 86.5 mm

SensactHs modular esp32
klaus-liebler/sensact
Es gibt vier Namespaces für Nachrichten "REQUEST" und "RESPONSE", "EVENT" und "ACKNOWLEDGE". Dies wird mit den beiden LSB des Versions-Namespace-Bytes erklärt (Somit bleiben 64 Versionierungsmöglichkeiten) Alle vier…
28 parts4Apache-2.0 - 4 layers95 × 95 mm

Cube motherboard
willem-pennings/balancing-cube
A cube that balances itself in a corner or edge using reaction wheels
52 parts1.1kGPL-3.0 - 2 layers129.9 × 63.6 mm

Traeger rev 2.3.0.kicad pro
jazzmonger/Traeger-PID-Controller
Traeger Smoker/Grill Controller based on an
45 parts36 - 2 layers168.8 × 78.9 mm

Gameboy3
ohasanov-hbrw/tribit32-advanced
A tri-microcontroller, overengineered GameBoy Advance clone. More value was given to the controls and the exterior look, which is cool!
61 parts8 - 2 layers134.6 × 49.5 mm

- 2 layers90 × 102 mm

- 2 layers119.4 × 98.9 mm

PCB Pami
FIPATECH/CDFR26_PAMI
Open source firmware and PCB for a differential mobile robot (PAMI) based on ESP32-S3 - Coupe de France de Robotique
25 parts6
Questions
How big is the Driver Control PCB PCB?
It measures 132.7 × 121.4 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Driver Control PCB use?
46 parts, built around the ESP32-S3-DEVKITC-1-N8 and SN65HVD230D. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Driver Control PCB KiCad files?
From the Monash-Railway-Express/KiCad_Files repository on GitHub, at the commit this page was made from: the board is PCBs/DriverControlsPCB/Driver_Control_PCB/Driver_Control_PCB.kicad_pcb and its schematic PCBs/Archive/ScreenPCB/Screen_PCB/Screen_PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Driver Control PCB design in my own project?
Its repository states no licence, so its author keeps all rights: ask Monash-Railway-Express before reusing the design.