

Esp32-dimmer slim
ESP32 multi channel dimmer
- Size
- 60 × 55 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 51
- Nets
- 37
- Pads
- 281
- Tracks, vias
- 274, 47
- Pours
- 25
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 10 Oct 2020
- Updated
- 21 Nov 2023
Overview
Esp32-dimmer slim is an open-source printed circuit board by MikkoTervala, from the MikkoTervala/esp32-dimmer repository on GitHub. It is a 2-layer board of 60 × 55 mm with 51 parts on 37 nets, routed with 274 tracks and 47 vias.
It is built around the ESP32-C3-WROOM-02-H4, R-78E3.3-0.5 and AON7524. Its parts include 11 resistors, 6 transistors, 5 capacitors, 5 connectors and 2 ICs. It belongs with the ESP32 and RISC-V boards of this library.
Main components
3ESP32-C3-WROOM-02-H4
SMD,20x18mm-105dBm -40℃~+105℃ 2.4GHz 20.5dBm 345mA 3V~3.6V 82mA Bluetooth5.0 ESP32-C3 On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,20x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesR-78E3.3-0.5
SIP,11.5x7.6mmDC-DC Power ModulesYLPTECAON7524
DFN-8(3x3)-55℃~+150℃ 1 N-channel 1.2V 2.25nF 25A、28A 3.3mΩ@10V 30V 50nC@10V DFN-8(3x3) MOSFETs ROHSAlpha & Omega SemiconductorMOSFETs
README
README.mdesp32-dimmer
PCB for the ESP32 WROOM module, with power supply and up to six mosfets for LED strip dimming.
2023 Model

Specifications
- Uses the ESP32-C3-WROOM-02-H4 microcontroller module
- Built in USB C connector for programming
- Designed to be made with SMD assembly
- 12 to 24V
- Designed for 5A single channel or 10A combined.
Notes
- Ordering 10 PCB's with SMD assembly not including ESP32 cost 65€
- Ordering 10 ESP32-C3 modules and regulators cost 43€
Next version ideas
- Add power LED
- Move 24V and GND pins to the middle of connector for shorter routing
- Expose all unused GPIO's as SMD test points
2020 Model
Specifications
- 12 or 24V
- Designed for 5A single channel or 10A combined with a low cost 1 oz PCB.
- Can be used with ESP32-WROOM-32 module or the DOIT Esp32 DevKit available from china.
- Can be used with CUI VXO7803-500 DC-DC converter or with "mini power supply module 3A" available from china.
- Fits inside square european electrical box.

Parts
51| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | Thermal via | AON7524:thermal via | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP11, TP12, TP13, TP14, TP15 |
| 6 | 100 | Resistor_SMD:R_0603_1608Metric | R4, R5, R6, R7, R8, R9 |
| 6 | AON7524 | AON7524:TRANS_AON7403 | Q1, Q2, Q3, Q4, Q5, Q6 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R10, R11 |
| 3 | JLCPCB tooling hole | AON7524:JLCPCB tooling hole | H1, H2, H3 |
| 2 | 10µf | Capacitor_SMD:C_1206_3216Metric | C4, C5 |
| 2 | 1N5819WS 1A 40V | Diode_SMD:D_SOD-323 | D1, D2 |
| 2 | 5.1k | Resistor_SMD:R_0603_1608Metric | R2, R3 |
| 2 | Conn_01x05 | Wago-2604:CONN_2604-1105_WAG | J4, J5 |
| 1 | 1µF | Capacitor_SMD:C_0603_1608Metric | C1 |
| 1 | BOOT | XKB_button:SW_Push_1P1T_XKB_TS-1187A | SW1 |
| 1 | C3 220nf | Capacitor_SMD:C_0603_1608Metric | C2 |
| 1 | C4 10µf | Capacitor_SMD:C_1206_3216Metric | C3 |
| 1 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | ESP32-C3-WROOM-02-H4 | esp32-c3:MODULE_ESP32-C3-WROOM-02-H4 | U1 |
| 1 | R-78E3.3-0.5 | Converter_DCDC:Converter_DCDC_RECOM_R-78E-0.5_THT | U2 |
| 1 | RESET | XKB_button:SW_Push_1P1T_XKB_TS-1187A | SW2 |
| 1 | USB_C_Receptacle_USB2.0 | usb-c:TYPE-C-31-M-12 | J1 |
More from MikkoTervala/esp32-dimmer
1- 2 layers67 × 68 mm

Similar boards
- 2 layers50 × 25 mm

Module-4ch dimmer
MikkoTervala/modular-esp32-dimmer
ESP32 based led dimmer with modular components
21 parts - 4 layers42 × 42 mm

- 4 layers52 × 52 mm

Hot plate controller
Angelo13C/hot-plate
It's based on an STM32F730R8T6. The board receives stable 24V from an external power supply unit and requires around 10A of current.
84 parts - 4 layers46 × 238 mm

Assembly review
OAK-WJR/rocket-flight-computer
Amateur rocket flight computer: single-board KiCad PCB (STM32H743), firmware and diagnostics
208 parts - 4 layers150 × 155 mm

Usb console server
TheKingOfChaos/Console-Server
48 RS-232 console ports on one Raspberry Pi: three identical boards, 16 ports each. Built from the design record of 2026-10-10. KiCad 10.0.7. This is Rev B (git tag rev-A is the first board).
361 parts - 4 layers52.5 × 46.5 mm

- 2 layers122.5 × 70.5 mm

Main pcb
Potato-eater/Legacy2026
github repo for Robocup Junior Australia lightweight soccer team
74 parts2 - 4 layers40.8 × 40.8 mm

Questions
How big is the Esp32-dimmer slim PCB?
It measures 60 × 55 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Esp32-dimmer slim use?
51 parts, built around the ESP32-C3-WROOM-02-H4, R-78E3.3-0.5 and AON7524. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32-dimmer slim KiCad files?
From the MikkoTervala/esp32-dimmer repository on GitHub, at the commit this page was made from: the board is esp32-dimmer-slim/esp32-dimmer-slim.kicad_pcb and its schematic esp32-dimmer-slim/esp32-dimmer-slim.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32-dimmer slim design in my own project?
Its repository states no licence, so its author keeps all rights: ask MikkoTervala before reusing the design.