Mbiarrambang-Lab/KiCADthis repository serves to keep all electrical PCBs schematics and Gerber files
Arduino Output X module is an open-source printed circuit board by Mbiarrambang-Lab, from the Mbiarrambang-Lab/KiCAD repository on GitHub. It is a 2-layer board of 64.6 × 102.6 mm with 35 parts on 50 nets, routed with 428 tracks and 20 vias.
It is built around the LM2596S-5.0 and IRF540N. Its parts include 10 diodes, 9 resistors, 8 transistors, 2 capacitors and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
this repository serves to keep all electrical PCBs schematics and Gerber files
| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 1N4007 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2, D4, D5, D6, D7, D8, D9 |
| 8 | 220 ohm | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | R1, R2, R3, R4, R5, R6, R7, R8 |
| 8 | IRF540N | Package_TO_SOT_THT:TO-220-3_Vertical | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8 |
| 1 | 1K ohms | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_Vertical | R9 |
| 1 | 1N5822-30A/40V | Diode_THT:D_DO-201AD_P15.24mm_Horizontal | D3 |
| 1 | 220uF/35V | Capacitor_THT:CP_Radial_D8.0mm_P3.80mm | C2 |
| 1 | 220uF/50V | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C1 |
| 1 | 47uH/3A | Inductor_THT:L_Radial_D10.0mm_P5.00mm_Fastron_07M | L1 |
| 1 | Arduino_Nano_v2.x | Module:Arduino_Nano | A1 |
| 1 | LED | Library:LED_D1.8mm_Horizontal_06.35mm_Z16.0mm | D10 |
| 1 | LM2596S-5 | Package_TO_SOT_THT:TO-264-5_Vertical | U2 |
| 1 | MAX485_MODULE_5V_LOGIC_TLL_TO_RS-485_CONVERTER | MAX485_MODULE_5V_LOGIC_TLL_TO_RS-485_CONVERTER:MODULE_MAX485_MODULE_5V_LOGIC_TLL_TO_RS-485_CONVERTER | U1 |
| 1 | Screw_Terminal_01x08 | Connector_Phoenix_GMSTB:PhoenixContact_GMSTBA_2,5_8-G_1x08_P7.50mm_Horizontal | J2 |
| 1 | Terminal_01x04 | Connector_IDC:IDC-Header_2x04_P2.54mm_Horizontal | J1 |
umut181/pcb-mini-racecar
A custom PCB design for a 2WD, IR-controlled differential-drive robot vehicle. Built to run on 2S–6S LiPo battery input, drive 5 V-based microcontrollers, and power low-reduction TT motors: all on a single compact board.
iowlabs/incubadora
Proyecto para confeccionar una incubadora bajo costo.
profdc9/DRSSTC-PCB-Pack
A pack of PCBs for a dual resonant solid state tesla coil setup. Pretty much everything you need.
AmericanRework/Pico-2x-BLDC
One RP2040 Pico drives two brushless motors! SimpleFOC + Halls + 2304 drivers + TO-220 mosfets or IGBTs. Plugs directly into 450x automower motors.
It measures 64.6 × 102.6 mm and has 2 copper layers, 1.6 mm thick.
35 parts, built around the LM2596S-5.0 and IRF540N. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Mbiarrambang-Lab/KiCAD repository on GitHub, at the commit this page was made from: the board is Arduino_Output-X-module/Arduino_Output-X-module.kicad_pcb and its schematic Arduino_Output-X-module/Arduino_Output-X-module.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Mbiarrambang-Lab before reusing the design.
