Skip to the content
2 layers44.6 × 18.6 mmLED Flip Flop, the printed circuit board in 3D

This project is a LED Flip-Flop Circuit PCB designed using KiCad.

Size
44.6 × 18.6 mm
Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
8
Pads
24
Tracks, vias
45, 0
Pours
1
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
28 Sep 2026
Updated
28 Sep 2026

Overview

LED Flip Flop is an open-source printed circuit board by Manideep136, from the Manideep136/-LED-Flip-Flop-Circuit repository on GitHub. It is a 2-layer board of 44.6 × 18.6 mm with 11 parts on 8 nets, routed with 45 tracks and 0 vias.

It is built around the BC547. Its parts include 4 resistors, 2 capacitors, 2 diodes, 2 transistors and 1 connector.

Main components

1

README

README.md

-LED-Flip-Flop-Circuit

LED Flip-Flop Circuit PCB

📌 Project Overview

This project is a LED Flip-Flop Circuit PCB designed using KiCad.

The circuit alternately switches between two LEDs, creating a simple blinking/flip-flop effect. The PCB was designed to provide a compact and organized implementation of the circuit using standard electronic components.

The project focuses on the complete PCB design process, including schematic creation, footprint assignment, component placement, PCB routing, and Design Rules Check (DRC).


🎯 Project Objectives

  • Design a simple LED flip-flop circuit.
  • Create the schematic in KiCad.
  • Assign suitable footprints to all components.
  • Design a compact PCB layout.
  • Route all electrical connections properly.
  • Add PCB labels and component references.
  • Perform ERC/DRC checks before fabrication.
  • Generate manufacturing files when required.

⚙️ Working Principle

The LED flip-flop circuit uses a transistor-based switching arrangement to alternately turn two LEDs ON and OFF.

When one transistor conducts, one LED is activated while the other remains OFF. The circuit then changes state, causing the LEDs to switch alternately.

Basic operation

`` +VCC │ ┌──┴──┐ │ │ LED1 LED2 │ │ Q1 Q2 │ │ └──┬──┘ │ GND

Q1 and Q2 alternately switch ON/OFF

🧩 PCB Design Process

  1. Schematic Design

The circuit schematic was created in KiCad with all components and electrical connections.

  1. Footprint Assignment

Suitable PCB footprints were assigned to each component based on the physical component/package being used.

  1. PCB Layout

The schematic was transferred to the PCB Editor and the components were arranged to create a compact and organized board.

  1. Routing

Copper tracks were routed between the components according to the schematic connections.

  1. Design Rules Check

The PCB was checked using KiCad's Design Rules Check (DRC) to identify issues such as:

Clearance violations Unconnected nets Track width violations Pad clearance problems Board-edge clearance problems 6. Final Verification

The PCB layout was visually inspected and checked before preparing the manufacturing files.

📐 PCB Features Compact PCB layout Two alternating LEDs Through-hole/component footprints where applicable Clearly marked component references Dedicated power input Organized component placement KiCad DRC verification Suitable for PCB fabrication

🚀 Future Improvements

Possible improvements include:

Add a power indicator LED Add adjustable blinking speed Use a potentiometer for frequency control Improve PCB size and component placement Add mounting holes Add polarity and power markings Manufacture and test the PCB Create an SMD version of the circuit 📚 Learning Outcomes

Through this project, the following PCB design skills were practiced:

KiCad schematic design Component and footprint selection PCB component placement Through-hole PCB design Copper track routing PCB layout optimization ERC and DRC checking Gerber generation PCB documentation 🛠️ Tools & Technologies

Design Software: KiCad PCB Design: KiCad PCB Editor Schematic: KiCad Schematic Editor Verification: ERC / DRC Output: Gerber + Drill Files

Project

LED Flip-Flop Circuit PCB

Designed as a practical electronics PCB design project using KiCad.

Parts

11
QtyValueFootprintReferences
210kResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR2, R3
2330Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_HorizontalR1, R4
2BC547Package_TO_SOT_THT:TO-92_InlineQ1, Q2
2C_PolarizedCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC1, C2
2LEDLED_THT:LED_D5.0mmD1, D2
1Conn_01x02_PinConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ1

Similar boards

  • 2 layers83.3 × 65.3 mmSimonShield, the printed circuit board in 3D

    SimonShield

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    46 parts14kMIT
  • 2 layers56 × 65 mmSeaTalk1, the printed circuit board in 3D

    SeaTalk1

    dotnet/iot

    This repo includes .NET Core implementations for various IoT boards, chips, displays and PCBs.

    24 parts2.4kMIT
  • 2 layers132.1 × 45.7 mmIPoS, the printed circuit board in 3D

    IPoS

    peterheinrich/InternetOverSpaghetti

    Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.

    42 parts342
  • 2 layers99.1 × 99.7 mmRC6502 General Video Adapter, the printed circuit board in 3D

    RC6502 General Video Adapter

    tebl/RC6502-Apple-1-Replica

    An expandable SBC-version of the Apple 1 computer, easy to get started with and lot of cool stuff that can be added to it!

    80 parts193GPL-3.0
  • 2 layers55.9 × 38.6 mmMega Amp, the printed circuit board in 3D

    Mega Amp

    theacodes/genesynth

    A Sega Genesis inspired synthesizer

    40 parts178Apache-2.0
  • 2 layers40 × 100 mmBack pcb, the printed circuit board in 3D

    Back pcb

    ZeroPhone/ZeroPhone-PCBs

    PCB files for ZeroPhone - for gerbers and schematics, go to "Releases" tab!

    118 parts148GPL-3.0
  • 2 layers100 × 100 mmCANBuster, the printed circuit board in 3D

    CANBuster

    GBert/misc

    miscellaneous stuff / unsorted

    182 parts99

Questions

How big is the LED Flip Flop PCB?

It measures 44.6 × 18.6 mm and has 2 copper layers, 1.6 mm thick.

What parts does the LED Flip Flop use?

11 parts, built around the BC547. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the LED Flip Flop KiCad files?

From the Manideep136/-LED-Flip-Flop-Circuit repository on GitHub, at the commit this page was made from: the board is LED Flip Flop/LED Flip Flop.kicad_pcb and its schematic LED Flip Flop/LED Flip Flop.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the LED Flip Flop design in my own project?

Its repository states no licence, so its author keeps all rights: ask Manideep136 before reusing the design.