2 layers107.1 × 39.9 mm
Amplifier
spel-uchile/anemometroSonico
https://code.google.com/p/uch-ultrasonic-anemometer/w/list
15 parts1GPL-3.0
4 layers46 × 93.7 mm
BaSe PWR V3 3
M-Welsch/base-pcb-powerBackup Server Circuit Board that contains power management and sbu
- Size
- 46 × 93.7 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 110
- Nets
- 78
- Pads
- 900
- Tracks, vias
- 765, 234
- Pours
- 23
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 30 Mar 2022
- Updated
- 30 Mar 2022
Overview
BaSe PWR V3 3 is an open-source printed circuit board by M-Welsch, from the M-Welsch/base-pcb-power repository on GitHub. It is a 4-layer board of 46 × 93.7 mm with 110 parts on 78 nets, routed with 765 tracks and 234 vias.
It is built around the ATTINY816-SN, INA2128U and ADG734BRU, with the BSS123, BS170 and CM2021Y330R-10 among its other parts. Its parts include 21 capacitors, 17 resistors, 7 transistors, 6 ICs and 6 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
12
ATTINY816-SN
SOIC-20-300mil-40℃~+105℃ 1.8V~5.5V 10bit 128Byte 18 20MHz 512Byte 8 Bit 8KB 8bit AVR Built-in FLASH SOIC-20-300mil Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)
INA2128U
SOIC-16-300mil-18V~-2.25V、2.25V~18V -40℃~+85℃ 1% 1.5mA 18mA 1V/V~10000V/V 1nA 2 200kHz 200nV/℃ 25uV 2nA 30pA/℃ 4.5V~36V 4V/us 7us 86dB 8nV/√Hz@1kHz External resistor gain、Overvoltage protection Single-Ended SOIC-16-300mil Instrumentation Amplifiers ROHSTexas InstrumentsInstrumentation Amplifiers
ADG734BRU
TSSOP20CMOS, 2.5 Ohms Low Voltage, Quad SPDT SwitchAnalog DevicesUncategorised
BSS123
SOT-23-55℃~+150℃ 1 N-channel 1.4V 1.4nC@10V 100V 170mA 22pF 2pF 3.5pF 680mW 6Ω@10V、10Ω@4.5V N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
BS170
TO-92-55℃~+150℃ 1 N-channel 1.2Ω@10V 17pF 2.1V 24pF 500mA 60V 7pF 830mW N-Channel TO-92 MOSFETs ROHSonsemiMOSFETs
CM2021Y330R-10
SMD-4P,5.9x5.6mm-40℃~+125℃ SMD-4P,5.9x5.6mm Common Mode Filters ROHSLairdCommon Mode FiltersXHP-2
P=2.5mm-25℃~+85℃ 1 1x2P 2 2.5mm Non-Latching PA6 UL94V-0 White Without Fins XH P=2.5mm Housings (Wire To Board / Wire To Wire ) ROHSJSTHousings (Wire To Board / Wire To Wire )
B4B-PH-K-S(LF)(SN)
插件,P=2mm-25℃~+85℃ 1 100V 1x4P 2A 2mm 4 4.5mm 4P 6mm 9.9mm Brass K Pin PA66 PH Through Hole Tin UL94V-0 White 插件,P=2mm Wire To Board Connector ROHSJSTWire To Board Connector
B9B-PH-K-S(LF)(SN)
插件,P=2mm-25℃~+85℃ 1 100V 19.9mm 1x9P 2A 2mm 4.5mm 6mm 9 9P Brass K Pin PA66 PH Through Hole Tin UL94V-0 White 插件,P=2mm Wire To Board Connector ROHSJSTWire To Board Connector
BSC028N06LS3 G
TDSON-8(5x6)-55℃~+150℃ 1 N-channel 100A 139W 13nF 2.2V 2.3nF 2.8mΩ@10V 60V TDSON-8(5x6) MOSFETs ROHSInfineon TechnologiesMOSFETsBSC093N04LSG
TDSON-8(5x6)-55℃~+150℃ 1 N-channel 1.9nF 16pF 24nC@10V 2V 35W 40V 450pF 49A 9.3mΩ@10V N-Channel TDSON-8(5x6) MOSFETs ROHSInfineon TechnologiesMOSFETs
EC2-12TNU
DIP,7.5x15mm-40℃~+85℃ 12V 1ms 2 Form C: 2C (DPDT-CO) 220V@DC、250V@AC 2A 2ms Dual Coil Silver Alloy DIP,7.5x15mm Magnetic Latching Relays ROHSKEMETMagnetic Latching Relays
README
README.mdBackup Server Power PCB
This circuit board has the following responsibilities
- take 12V Power connection from outside
- generate 5V and 3.3V
- supply BananaPi and HDD
- switch power to BananaPi and HDD (separately)
- take BananaPi M1
- connect to HMI Board
Parts
110| Qty | Value | Footprint | References |
|---|---|---|---|
| 11 | 47k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | 2k3, R2, R4, R8, R14, R15, R16, R17, R20, R25, Ron1 |
| 7 | 1µF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C2, C3, C8, C10, C13, C17, C20 |
| 7 | 742792602 | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | FB3, FB4, FB5, FB6, FB7, FB9, FB10 |
| 4 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C6, C7, C16 |
| 4 | ASPHSPH24K51 | G7_Custom:BOM_ITEM | Cable_Stepper_preconfected1, Cable_Stepper_preconfected2, Cable_Stepper_preconfected3, Cable_Stepper_preconfected4 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 4 | NO | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R7, R18, R26, R27 |
| 3 | 0R | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R9, R10, R11 |
| 3 | 100k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R12, R21, R22 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5, R19, Rfbt1 |
| 3 | 10µF | Capacitor_SMD:C_1210_3225Metric_Pad1.42x2.65mm_HandSolder | C5, C15, C18 |
| 3 | 1k2 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | 2k4, R6, R24 |
| 3 | BSS123 | Package_TO_SOT_SMD:SOT-23 | Q2, Q6, Q7 |
| 2 | 0 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R13, R23 |
| 2 | 100µF | Capacitor_SMD:C_1210_3225Metric_Pad1.42x2.65mm_HandSolder | C4, C11 |
| 2 | 1N4148 | Diode_SMD:D_SOD-123F | D1, D2 |
| 2 | 220µF | Capacitor_SMD:C_Elec_6.3x7.7 | C14, C19 |
| 2 | ASXHSXH22K51 | G7_Custom:BOM_ITEM | Cable_BPi_SPLY_preconfected1, Cable_BPi_SPLY_preconfected2 |
| 2 | BS170 | Package_TO_SOT_THT:TO-92_Inline | Q1, Q5 |
| 2 | CM2021Y330R-10 | G7_Custom:CMC_Laird_CM2021Y330R-10 | FL1, FL2 |
| 2 | NO | Diode_SMD:D_SMA | D4, D5 |
| 2 | XHP-2 | G7_Custom:BOM_ITEM | Conn_Socket_BPi_SPLY_atJ5, Conn_Socket_BPi_SPLY1 |
| 1 | 0151670333 | G7_Custom:BOM_ITEM | FFC_Cable1 |
| 1 | 1,87K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | Rfbb1 |
| 1 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C9 |
| 1 | 12V Power In | G7_Custom:BarrelJack_Wuerth_6941xx301002 | J1 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R3 |
| 1 | 1m | Resistor_SMD:R_1206_3216Metric_Pad1.42x1.75mm_HandSolder | R1 |
| 1 | 1nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C24 |
| 1 | 47nF | Capacitor_SMD:C_1210_3225Metric_Pad1.42x2.65mm_HandSolder | C12 |
| 1 | 742792093 | Inductor_SMD:L_0805_2012Metric_Pad1.15x1.40mm_HandSolder | FB2 |
| 1 | 824501121 | Diode_SMD:D_SMA | D3 |
| 1 | A4988_Module | G7_Custom:A4988_Module | SCT1 |
| 1 | ADG734 | Package_SO:TSSOP-20_4.4x6.5mm_P0.65mm | U3 |
| 1 | AP2204K-3.3 | Package_TO_SOT_SMD:SOT-23-5_HandSoldering | U7 |
| 1 | ASPHSPH24K152 | G7_Custom:BOM_ITEM | Cable_HDD_ENDSW_preconfected2 |
| 1 | ATtiny816-S | Package_SO:SOIC-20W_7.5x12.8mm_P1.27mm | U5 |
| 1 | B4B-PH-K-S(LF)(SN) | Connector_JST:JST_PH_B4B-PH-K_1x04_P2.00mm_Vertical | J6 |
| 1 | B9B-PH-K-S(LF)(SN) | Connector_JST:JST_PH_B9B-PH-K_1x09_P2.00mm_Vertical | J4 |
| 1 | BPi Supply | Connector_JST:JST_XH_S2B-XH-A_1x02_P2.50mm_Horizontal | J2 |
| 1 | BSC028N06LS3 | Package_TO_SOT_SMD:TDSON-8-1 | Q3 |
| 1 | BSC093N04LS | Package_TO_SOT_SMD:TDSON-8-1 | Q4 |
| 1 | BaSe_PWR_V3_2 | G7_Labels:BaSe_PWR_V3_2 | PCB1 |
| 1 | BananaPi_M1 | G7_Custom:BananaPi-M1 | M1 |
| 1 | DebugAtTiny | G7_Custom:JST_XH_B4B-XH-AM_1x04_P2.50mm_Vertical | J3 |
| 1 | EC2-12TNU | G7_Custom:Relay_Kemet_EC2-12TNU | K1 |
| 1 | Fuse | Fuse:Fuse_Littelfuse-NANO2-451_453 | F1 |
| 1 | INA212 | Package_TO_SOT_SMD:SOT-363_SC-70-6_Handsoldering | U1 |
| 1 | LMZ12003 | G7_Custom:LMZ12003_Handsolder | U2 |
| 1 | LTC4359-MS8 | G7_Custom:MSOP-8_3x3mm_P0.65mm_Py0.45mm | U4 |
| 1 | Molex 0522071860 | G7_Custom:Conn_FFC_Molex_52207-1860 | J5 |
| 1 | NO | Diode_SMD:D_SMC | D6 |
| 1 | PHR-4 | G7_Custom:BOM_ITEM | Conn_Socket_Stepper1 |
| 1 | PHR-6 | G7_Custom:BOM_ITEM | Conn_Socket_at_Stepper1 |
| 1 | PHR-9 | G7_Custom:BOM_ITEM | Conn_Socket_PWR_HDD1 |
Similar boards
- 6 layers130 × 85 mm
CS Shim
shomi74/TUCAN_64CH_SHIM_CURRENT_SUPPLY
64-channel modular ultra-stable bipolar current supply system developed for TUCAN neutron EDM shim-coil magnetic-field control using precision mixed-signal feedback architecture and low-noise PCB design.
156 parts - 4 layers114.3 × 114 mm
- 2 layers184.2 × 59.7 mm
Power Distribution Board Rock64
AngelDMercedes/UNS_SBCPWRDIST
These are the design files for a DIY power distribution board for Single Board Computers powered by an ATX PSU
69 parts2GPL-3.0 - 2 layers58 × 63 mm
Camping LightRelay
Rustaphor/LightRelay4Camping
Analog light sensor to night power up LED garland. For Camping use.
91 parts2GPL-3.0 - 4 layers50 × 50 mm
A3-srad camera v2
eric-handley/a3-srad-cameras
Please read the following document carefully as there are several important notes that could result in data loss or damage if ignored. After the rocket is recovered, please follow Post-Flight Operations.
181 parts - 2 layers
Indicator driver
virtualagc/agc_hardware
Schematics and board layouts for an Apollo Guidance Computer replica
176 parts118MIT - 4 layers48 × 46 mm
Questions
How big is the BaSe PWR V3 3 PCB?
It measures 46 × 93.7 mm and has 4 copper layers, 1.6 mm thick.
What parts does the BaSe PWR V3 3 use?
110 parts, built around the ATTINY816-SN, INA2128U, ADG734BRU and BSS123. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BaSe PWR V3 3 KiCad files?
From the M-Welsch/base-pcb-power repository on GitHub, at the commit this page was made from: the board is BaSe_PWR_V3_3.kicad_pcb and its schematic BaSe_PWR_V3_3.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BaSe PWR V3 3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask M-Welsch before reusing the design.