

ESP8266-breakout
Breakout board for the ESP8266-03, Chaos InKL version
- Size
- 42.5 × 45.1 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 38
- Pads
- 137
- Tracks, vias
- 273, 27
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 3
- Created
- 4 Dec 2014
- Updated
- 17 Feb 2016
Overview
ESP8266-breakout is an open-source printed circuit board by LongHairedHacker, from the LongHairedHacker/ESP8266-breakout repository on GitHub. It is a 2-layer board of 42.5 × 45.1 mm with 46 parts on 38 nets, routed with 273 tracks and 27 vias.
It is built around the FT230XS-R. Its parts include 16 resistors, 10 capacitors, 3 ICs, 3 diodes and 3 connectors. It belongs with the interfaces and adapters boards and the ESP8266 boards of this library.
Main components
1README
README.mdESP8266 Breakout Chaos InKL Version
Slightly modified version of limpkins ESP8266 breakout board. See: http://www.limpkin.fr/index.php?post/2014/11/27/A-Development-Board-for-the-ESP8266-03 for the original files.
Licenses
Anything in the folder libs/smisitoto_eu/ is taken from http://smisioto.no-ip.org/elettronica/kicad/kicad-en.htm The files are made avaible under the Creative Commons license rev2.5 Attribution-ShareAlike. (see https://creativecommons.org/licenses/by-sa/2.5/)
The Chaos InKL logo is licensed CC BY-NC-SA 3.0.
The exploding open hardware logo (artwork/hacker_logo.mod) is my private logo, you are not allowed to use it on your own design and you should therefore remove it, after forking this repository.
All remaining files repository are under the CERN Open Hardware Licence v1.2.
Thanks to limpkin for the initial design.
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | 1k | SM0603_Resistor | R1, R2, R4, R5, R9, R10, R11, R12, R13, R14, R15, R16, R17, R18 |
| 5 | 4.7uF | SM0805 | C1, C2, C3, C9, C10 |
| 3 | 100nF | SM0603_Resistor | C4, C7, C8 |
| 3 | P*** | 1pin | 1PIN, 1PIN, 1PIN |
| 2 | 27R | SM0603_Resistor | R6, R7 |
| 2 | 47pF | SM0603_Resistor | C5, C6 |
| 2 | TEST | SM0603_Resistor | W1, W2 |
| 1 | CONN_12 | SIL-12 | P1 |
| 1 | CONN_2 | coaxial_u.fl-r-smt-1 | P2 |
| 1 | ESP8266-3 | ESP8266-3 | U2 |
| 1 | FILTER | SM0805 | FB1 |
| 1 | FT230XS | ssop-16 | U3 |
| 1 | LED | SM0603_Capa | D3 |
| 1 | MOS_N | SOT23GDS_L | Q2 |
| 1 | MOS_P | SOT23GDS_L | Q1 |
| 1 | NCP1117LP | sot223 | U1 |
| 1 | RXLED | SM0603_Capa | D1 |
| 1 | SW_PUSH | SW_PUSH_SMALL | SW1 |
| 1 | TXLED | SM0603_Capa | D2 |
| 1 | USB-MICRO-B2 | USB_MINI_B | CON1 |
| 1 | chaosinkl_silkbot_25_00mm | chaosinkl_silkbot_25_00mm | G*** |
| 1 | logo_hacker_silkbot_15_00mm | logo_hacker_silkbot_15_00mm | G*** |
Similar boards
- 2 layers229.9 × 111.8 mm

- 2 layers203.2 × 149.9 mm

- 2 layers77.5 × 40.6 mm

Link adapter
jkominek/piano-conversion
Hardware, and some firmware, for acoustic piano to MIDI controller conversion.
42 parts53 - 4 layers62 × 42 mm

- 4 layers65 × 56 mm

Copilot Lite
BayLibre/Copilot
Manage a DUT power and serial through a single USB port, no additional software required.
80 parts22MIT - 2 layers48.2 × 49.3 mm

Nixie pipe
tuna-f1sh/nixiepipe-hardware
Hardware design files and firmware for my Nixie Pipe modules
49 parts19 - 2 layers120 × 98 mm

BioAmp v1.1.0
prototipado/bioamp
BioAmp is an opensource project of a multichannel biopotential adquisition system for EEG, EMG, EOG and EOG signals.
139 parts16 - 2 layers41 × 14 mm

96boards uart
96boards/96boards-uart
96Boards UART adapter hardware design files
31 parts13BSD-2-Clause
Questions
How big is the ESP8266-breakout PCB?
It measures 42.5 × 45.1 mm and has 2 copper layers, 1.6 mm thick.
What parts does the ESP8266-breakout use?
46 parts, built around the FT230XS-R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP8266-breakout KiCad files?
From the LongHairedHacker/ESP8266-breakout repository on GitHub, at the commit this page was made from: the board is esp8266_breakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP8266-breakout design in my own project?
Its repository states no licence, so its author keeps all rights: ask LongHairedHacker before reusing the design.