
BMT BionX Minimum Translator vereinfacht
stancecoke/BionX_Minimal_Translator
Drive your BionX motor with a no-name battery and a Kunteng LCD-display without any further BionX-components

Breakout and control interface PCB designed for Robocon 2024 R1 robot, supporting Arduino Mega + Host Shield stacking, motor control interfaces, and regulated power distribution from external supply modules.
R1 PCB 2024-25 VRC is an open-source printed circuit board by Loki045, from the Loki045/R1_Robocon_24_Breakout repository on GitHub. It is a 2-layer board of 132.3 × 100.3 mm with 66 parts on 96 nets, routed with 252 tracks and 0 vias.
It is built around the IRF3205. Its parts include 34 connectors, 7 resistors, 6 capacitors, 3 diodes and 2 transistors. It belongs with the robots and motor control and interfaces and adapters boards and the AVR (ATmega, ATtiny) boards of this library.
Breakout and control interface PCB designed for Robocon 2024 R1 robot, supporting Arduino Mega + Host Shield stacking, motor control interfaces, and regulated power distribution from external supply modules.
This repository contains the hardware design files for the R1 Control Breakout PCB used in the Robocon 2024 robot.
The board was designed to serve as a stackable control and interface breakout, enabling easy connection of motors, actuators, and control modules using an Arduino Mega + Host Shield stack.
In Robocon 2024, Robot 1 (R1) performed the following operations:
This PCB supported the control and actuator interfacing required to perform these tasks.
The R1 PCB was designed as a centralized control breakout board, allowing:
This modular approach simplified robot wiring and improved system maintainability.
Regulated voltages were supplied from an external power distribution board.
These headers enabled clean routing of regulated voltages to connected modules.
These supported the mechanisms required for seedling placement and ball throwing operations.
Designed to support:
This stack allowed wireless/manual control of the robot.
R1_PCB_2024-25_VRC/
├── PCB Layout File
├── Project File
├── Schematic File Images/
├── Top Layer View
├── Bottom Layer View
├── 3D View
.gitignore
README.md
This PCB was used in the Robocon 2024 R1 robot, providing structured connectivity for locomotion motors, actuators, and control interfaces required for seedling placement and ball-throwing operations.
Developed as part of the Robocon 2024 electronics system, contributing to hardware layout planning, connector design, and system-level integration for robot subsystems.
Schematic
F.Cu Layer View
B.Cu Layer View
3D View
This board was designed to reduce wiring complexity, improve modularity, and enable rapid maintenance during robot testing and competition.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 14 | Conn_01x03 | Connector_JST:JST_XH_B3B-XH-A_1x03_P2.50mm_Vertical | J5, J6, J7, J8, J9, J10, J11, J12, J13, J14, J24, J25, J26, J27 |
| 6 | Conn_01x02 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J17, J18, J19, J21, J22, J23 |
| 4 | Conn_01x05 | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | 5V1, 7.4V1, DIR1, GND1 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2 | H1, H2, H3, H4 |
| 4 | R | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R3, R5, R6, R7 |
| 3 | 0.1uF | Capacitor_THT:C_Disc_D3.0mm_W1.6mm_P2.50mm | C3, C4, C5 |
| 3 | Conn_01x02 | Connector:JWT_A3963_1x02_P3.96mm_Vertical | J15, J16, J20 |
| 3 | LED | LED_THT:LED_D5.0mm | D1, D2, D3 |
| 2 | . | modfied footprints:logo | ., . |
| 2 | 100 nf | Capacitor_THT:C_Radial_D5.0mm_H7.0mm_P2.00mm | C2, C6 |
| 2 | 360 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R1, R4 |
| 2 | Analog | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J3, J5 |
| 2 | BACK | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J3, J4 |
| 2 | FRONT | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J1, J2 |
| 2 | IRF3205 | Package_TO_SOT_THT:TO-220-3_Vertical | Q3_N1, Q3_N2 |
| 2 | LOGO | kicad footprints:VRC_fox_white | G***, G*** |
| 1 | 10 mf | Capacitor_THT:C_Radial_D5.0mm_H7.0mm_P2.00mm | C1 |
| 1 | 220 | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P5.08mm_Horizontal | R2 |
| 1 | ARDUINO_MEGA_2560_REV3_A000067 | modfied footprints:ARDUINO_ARDUINO_MEGA_2560_REV3_A000067 | A2 |
| 1 | Communication | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J6 |
| 1 | Conn_02x03_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | ICSP1 |
| 1 | Digital | Connector_PinSocket_2.54mm:PinSocket_2x18_P2.54mm_Vertical | J7 |
| 1 | PWM | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J4 |
| 1 | PWM | Connector_PinSocket_2.54mm:PinSocket_1x10_P2.54mm_Vertical | J2 |
| 1 | Power | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J1 |

stancecoke/BionX_Minimal_Translator
Drive your BionX motor with a no-name battery and a Kunteng LCD-display without any further BionX-components


jayanta525/dual-h-bridge
Dual H-Bridge Controller with IRF3205 and IR2104 MOSFET Driver, and with ATMega328P-AU PWM Controller




ampnics/Project-10
Mater KiCad with Projects is a series of lectures in which we are learning PCB designing

It measures 132.3 × 100.3 mm and has 2 copper layers, 1.6 mm thick.
66 parts, built around the IRF3205. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Loki045/R1_Robocon_24_Breakout repository on GitHub, at the commit this page was made from: the board is R1_PCB_2024-25_VRC/R1_PCB_2024-25_VRC.kicad_pcb and its schematic R1_PCB_2024-25_VRC/R1_PCB_2024-25_VRC.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Loki045 before reusing the design.