

Rpi breakout
- Size
- 36.8 × 24.1 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 40
- Nets
- 58
- Pads
- 187
- Tracks, vias
- 219, 13
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 20 Aug 2025
- Updated
- 21 Aug 2025
Overview
Rpi breakout is an open-source printed circuit board by LastZactionHero, from the LastZactionHero/rpi_breakout repository on GitHub. It is a 4-layer board of 36.8 × 24.1 mm with 40 parts on 58 nets, routed with 219 tracks and 13 vias.
It is built around the W25Q16JVZPIQ, AP2112K-3.3TRG1 and SKRWAEE030, with the ABM8-12.000MHZ-B2-T and USB4520-03-0-A among its other parts. Its parts include 15 capacitors, 13 resistors, 3 ICs, 3 connectors and 1 crystal. It belongs with the interfaces and adapters boards of this library.
Main components
5W25Q16JVZPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10ms 10uA 120ms@(32KB) 133MHz 16Mbit 2.7V~3.6V 20 Years 400us Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbond ElecNOR FLASHAP2112K-3.3TRG1
SOT-25-5-40℃~+85℃@(Ta) 1 250mV@(600mA) 3.3V 50uVrms 55uA 600mA 65dB@(1kHz) 6V Fixed Over Current Protection、Thermal Shutdown、Enable control Positive SOT-25-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSDiodes IncorporatedVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsSKRWAEE030
SMD-4P,3.7x3.7mm-30℃~+85℃ 0.35mm 1.6N 12V 3.7mm 3.7mm 500,000 Cycles 50mA J-Lead Round Button SPST-NO Surface Mount,Vertical SMD-4P,3.7x3.7mm Tactile Switches ROHSALPSALPINETactile SwitchesABM8-12.000MHZ-B2-T
SMD3225-4P-20℃~+70℃ 120Ω 12MHz 18pF Crystal Oscillator ±20ppm ±50ppm SMD3225-4P Crystals ROHSAbraconCrystalsUSB4520-03-0-A
SMD-25℃~+85℃ 1 12P 48V 5A Black Female Surface Mount, Right Angle Type-C USB 2.0 SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB Connectors
Parts
40| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C2, C4, C5, C6, C7, C8, C10, C13 |
| 7 | 10k | Resistor_SMD:R_0402_1005Metric | R5, R6, R7, R8, R9, R10, R11 |
| 4 | 1uF | Capacitor_SMD:C_0402_1005Metric | C9, C11, C12, C16 |
| 2 | 27 | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | 27pF | Capacitor_SMD:C_0402_1005Metric | C14, C15 |
| 2 | 5.1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 68 | Resistor_SMD:R_0402_1005Metric | R12, R13 |
| 2 | Conn_01x10 | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J2, J3 |
| 2 | LED | LED_SMD:LED_0805_2012Metric | D_POWER1, D1 |
| 2 | SKRWAEE030 | KiCad:SKRWAEE030 | BOOTSEL1, RESET1 |
| 1 | ABM8-12.000MHZ-B2-T | ABM8_12_000MHZ_B2_T:XTAL_ABM8-12.000MHZ-B2-T | Y1 |
| 1 | AP2112K-3.3TRG1 | AP2112K_3_3TRG1:SOT95P285X140-5N | U3 |
| 1 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J_SWD1 |
| 1 | SC0914_13_ | SC0914_13_:QFN40P700X700X90-57N | U1 |
| 1 | USB4520-03-0-A | KiCad_USB:USB4520030A | J1 |
| 1 | W25Q16JVZPIQ | W25Q16JVZPIQ:SON127P500X600X80-9N | U2 |
Similar boards
- 4 layers125 × 95 mm

- 2 layers51 × 21 mm

Bench rp2040 usb hid 5eab0a5d
mrcha033/hw-codesign
Agentic hardware co-design: brief to KiCad, firmware, 3D review, and explicit fabrication blockers.
15 parts2Apache-2.0 - 4 layers42.3 × 47 mm

- 4 layers95 × 67 mm

- 4 layers36 × 77 mm

- 2 layers139.5 × 92 mm

- 4 layers26 × 30 mm

- 2 layers5 × 11.2 mm

Questions
How big is the Rpi breakout PCB?
It measures 36.8 × 24.1 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Rpi breakout use?
40 parts, built around the W25Q16JVZPIQ, AP2112K-3.3TRG1, SKRWAEE030 and ABM8-12.000MHZ-B2-T. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Rpi breakout KiCad files?
From the LastZactionHero/rpi_breakout repository on GitHub, at the commit this page was made from: the board is rpi_breakout.kicad_pcb and its schematic rpi_breakout.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Rpi breakout design in my own project?
Its repository states no licence, so its author keeps all rights: ask LastZactionHero before reusing the design.