

KEY LED LM321
Eurorack development from 0
- Size
- 16.5 × 14 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 9
- Nets
- 9
- Pads
- 29
- Tracks, vias
- 0, 0
- Routed
- Not yet
- KiCad
- KiCad 7 (file 20221018)
- Created
- 6 May 2024
- Updated
- 9 Nov 2024
Overview
KEY LED LM321 is an open-source printed circuit board by LAJILaaaaaaaa, from the LAJILaaaaaaaa/Eurorack repository on GitHub. It is a 2-layer board of 16.5 × 14 mm with 9 parts on 9 nets.
It is built around the LM321. Its parts include 3 capacitors, 3 resistors, 1 IC, 1 connector and 1 switch.
Main components
1README
README.mdEurorack
模块尺寸规范
[01] 物理规格参考链接_doepfer
[02] 物理规格参考链接_intellijel
信号和电压
音频信号
通常在10Vpp范围内(从-5V到+5V)。
控制电压
由LFO和ADSR等调制源产生,LFO通常从-2.5 V到+2.5 V(5 Vpp),ADSR从0 V到+8 V。
触发电压
触发器、门或时钟信号,启动过程或功能,是矩形信号,典型电压电平为0/+5 V。在触发应用程序的情况下,通常是用于触发事件的信号的上升边缘。
常用网站
模块制造商
- makenoise
- instruo
- 4ms
- mutable-instruments
- busycircuits
- intellijel
- expert-sleepers
- befaco
- Der Mann mit der Maschine
- antumbra
- QU-Bit
- 2HP
- musicthing
- abyssdevices
- monome
其他
开发者套件
开发者套件的目的是将Eurorack中常用的电路模块化,方便Eurorack开发者们在面包板上进行电路实验。
PJ301M-12 [blocked]
单声道音频输入模块
PJ301BM [blocked]
单声道音频输入模块
KEY_LED [blocked]
带led灯的轻触开关模块
KEY [blocked]
轻触开关模块
LED [blocked]
LED灯模块
ENCODER [blocked]
编码器模块
常用电路
- ne555时钟发生电路
- 白噪声发生电路
- 粉色噪声发生电路
- 采样保持电路
- 电压比较器电路
- 门转触发电路
- 触发转门电路
- 随机门发生器
- 门随机跳过电路
- AR包络发生器电路
- 随机电压发生电路
LED灯光电路
- 三极管
- lm321运算放大器
- 单led
- 双led
- rgb
运算放大器电路
- 同相比例放大
- 反相比例放大
- 加法器
- 电压跟随器
硬件驱动库
- OLED
- Key
- Encoder
- LED
- ADC
- DAC
- CAP1214电容触摸
- MAX7219数码管驱动
模拟电路
- multisim电路仿真
PCB绘制
Kicad
- PCB艺术外观
合成器电路
参考网站
DSP算法
常用开发板
- Stm32
- f103c8t6
- f411c8t6
- 树莓派
- pico
- 5
- 4B+
- Arduino
- nano
- Uno R4
常用硬件
- 基础
- 电阻
- 电容
- 二极管
- 1N4148高速开关二极管
- 肖特基二极管
- 1N5819HW
- BAT54SLT1G双肖特基二极管
- NPN三极管
- MMBT3904
- LDO
- LM1117
- MCP1703 LDO Vref
- 磁珠
- 控制
- 按键
- 电位器
- 编码器
- 显示
- LED灯
- OLED显示器
- 0.96英寸(驱动SSD1306)
- 1.29英寸(驱动CH1115)
- 1.3英寸
- 1.54英寸(驱动SSD1306)
- 2.7英寸
- 输入输出
- 3.5mm单声道插座
- type-c插座
- 连接
- 2.54排针排母
- 1.27排针排母
- 跳线帽
- 11mm,m2铜柱
- 运算放大器
- TL072
- TL074
- MCP6002 R2R
- MCP6004 R2R
- OPA4171 四运放
- OPA2171 双运放
- LM324 四运放
- ADC
- ADS1115
- DAC
- WM8731
- DAC8564
- DAC128S085
- 其他
- LM4040
- CD4051
- 74hc595 移位寄存器
- 74AHCT1G125
- MAX7219 数码管驱动
开源模块存储库
存储一些开源的模块资料,防止丢失
Parts
9| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | 0.1uf | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 1 | 1k | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J1 |
| 1 | LM321 | Package_TO_SOT_SMD:SOT-23-5 | U1 |
| 1 | SW_LED | Eurorack:Button_LED | SW1 |
More from LAJILaaaaaaaa/Eurorack
1- 2 layers

Similar boards
- 2 layers36.5 × 56 mm

- 4 layers17.5 × 35 mm

KungFuSID
Sgw32/KungFuSID
Kung Fu SID is a firmware based on Kung Fu Flash which allows SID emulation
35 parts65 - 2 layers99 × 99.8 mm

- 2 layers13 × 10.2 mm

- 4 layers100 × 100 mm

PCB Motor
SaralTayal123/PCB_Motors
Code & Firmware to generate continuous coil PCB motor designs
33 parts10 - 4 layers100 × 50 mm

Psu ext
PSU-Ext-Org/psu-ext-hardware
A repository to store PSU-EXT hardware design assets, schematics, circuit diagrams, CAD files and manufacturing data.
137 parts9CERN-OHL-S-2.0 - 4 layers86.4 × 69.9 mm

- 2 layers55 × 53 mm

Heatgun
m24h/heatgun
A small hot air station for soldering, using type-858 heat gun as handle, STC8G1k17 as MCU, copper wire resistor for cold junction compensation
40 parts3Apache-2.0
Questions
How big is the KEY LED LM321 PCB?
It measures 16.5 × 14 mm and has 2 copper layers, 1.6 mm thick.
What parts does the KEY LED LM321 use?
9 parts, built around the LM321. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the KEY LED LM321 KiCad files?
From the LAJILaaaaaaaa/Eurorack repository on GitHub, at the commit this page was made from: the board is DevKit/KEY_LED_LM321/KEY_LED_LM321.kicad_pcb and its schematic DevKit/KEY_LED_LM321/KEY_LED_LM321.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the KEY LED LM321 design in my own project?
Its repository states no licence, so its author keeps all rights: ask LAJILaaaaaaaa before reusing the design.