Skip to the content
2 layers144 × 127 mmTuco, the printed circuit board in 3D

LTI Modular DAQ & Flight Computer Based on the Teensy 4.1

Size
144 × 127 mm
Copper layers
2
Thickness
1.6 mm
Parts
27
Nets
143
Pads
212
Tracks, vias
0, 0
Routed
Not yet
KiCad
KiCad 10.0 (file 20260206)
Created
1 Oct 2026
Updated
5 Nov 2026

Overview

Tuco is an open-source printed circuit board by KXR-UCF, from the KXR-UCF/mdfc repository on GitHub. It is a 2-layer board of 144 × 127 mm with 27 parts on 143 nets.

It is built around the TEENSY 4.1 and S16B-XH-A. Its parts include 8 connectors and 1 IC. It belongs with the NXP (LPC, Kinetis, i.MX RT) boards of this library.

Main components

2

README

heisenberg/readme.md

LTI Modular DAQ & Flight Computer

image

This is a teensy 4.1 based analog data acquisition system and flight computer.

It consists of 5 PCBs:

Heisenberg (Mainboard)

The Heisenberg board carries the Teensy 4.1 and all the modules, mounts to the chassis, and has the servo/aux connector. It provides the same pinout to each of the two modules so they are interchangeable. image image

Fring/Schrader (Flight/Ground Power Modules, these will most likely be two different PCBs)

These boards convert input voltage, either from battery during flight use or power over ethernet for ground use, into the necessary voltages for the rest of the system. They also handle the ethernet input to the Teensy 4.1, and allow the Teensy 4.1 to independently enable/disable each voltage output. image image

Goodman (ADC Module) This board carries the HiLetgo ADS1256 board, along with analog circuitry and a sensor connector, for use with analog sensors such as Pressure Transducers, Thermocouples, and Load Cells. A future development will be to create a fully SRAD ADC module instead of relying on the COTS ADS1256 board.

Pinkman (Flight Sensor/Telemetry Module) This board contains flight sensors (IMU and barometric), a GPS receiver, and a 433 MHz LoRa radio for telemetry in flight. image image

The Heisenberg board has 2 module slots and 1 power module slot, and its two primary configurations are as follows:

  • DAQ/Ground use: Module A: Goodman Module B: Goodman Power Module: Schrader PoE powered, 16 channel analog input, no flight sensor/telemetry, no servo output.
  • Flight use: Module A: Goodman Module B: Pinkman Power Module: Fring Battery powered, 8 channel analog input, flight sensors/telemetry, servo output.

The primary goals of this project are:

  • Emulate the EE design, collaboration, integration, and test processes used in the aerospace industry to provide a valuable learning experience for members
  • Increase the sampling speed of the DAQ system
  • Increase the expandability of the DAQ system
  • Move ADCs closer to sensors to decrease analog wire length for less noise
  • Improve power filtering for ADCs and load cells
  • Record fast analog data in flight
  • Transmit flight data to ground via telemetry at the highest speed possible
  • Create a platform that can be expanded and upgraded by future students

Parts

27
QtyValueFootprintReferences
2Conn_02x10_Odd_EvenConnector_PinSocket_2.54mm:PinSocket_2x10_P2.54mm_VerticalJ1, J2
1Conn_01x10Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_VerticalJ8
1Conn_01x16Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_VerticalJ3
1Conn_01x20Connector_PinHeader_2.54mm:PinHeader_1x20_P2.54mm_VerticalJ6
1Conn_01x23Connector_PinHeader_2.54mm:PinHeader_1x23_P2.54mm_VerticalJ5
1LOGOMDFC Common:kxr-logo-15mmG***
1S16B-XH-AConnector_JST:JST_XH_S16B-XH-A_1x16_P2.50mm_HorizontalJ4
1Screw_Terminal_01x04TerminalBlock_Phoenix:TerminalBlock_Phoenix_PT-1,5-4-5.0-H_1x04_P5.00mm_HorizontalJ7
1Teensy4.1MDFC Common:Teensy41U1

The 10 most common of 27 parts.

More from KXR-UCF/mdfc

4
  • 2 layers117 × 63.5 mmHeisenberg template, the printed circuit board in 3D

    Heisenberg template

    KXR-UCF/mdfc

    LTI Modular DAQ & Flight Computer Based on the Teensy 4.1

    19 parts3
  • 2 layers100 × 21.5 mmSchrader, the printed circuit board in 3D

    Schrader

    KXR-UCF/mdfc

    LTI Modular DAQ & Flight Computer Based on the Teensy 4.1

    9 parts3
  • 2 layers100 × 38 mmGoodman pro, the printed circuit board in 3D

    Goodman pro

    KXR-UCF/mdfc

    LTI Modular DAQ & Flight Computer Based on the Teensy 4.1

    7 parts3
  • 4 layers117 × 63.5 mmHeisenberg, the printed circuit board in 3D

    Heisenberg

    KXR-UCF/mdfc

    LTI Modular DAQ & Flight Computer Based on the Teensy 4.1

    6 parts3

Similar boards

  • 2 layers118.1 × 101.6 mmTeensy eurorack, the printed circuit board in 3D

    Teensy eurorack

    newdigate/teensy-eurorack

    Hardware Design: Eurorack shield for teensy 4.1 with 14 in / 16 out analog channels

    102 parts259MIT
  • 2 layers240 × 240 mmKfchess, the printed circuit board in 3D

    Kfchess

    misprit7/real-time-chess

    A physical chess board without the concept of turns

    235 parts254MIT
  • 2 layers304.8 × 170.8 mm00Key, the printed circuit board in 3D

    00Key

    ZeroZeroOne-dev/00Key

    00Key a 75% keyboard

    268 parts241GPL-3.0
  • 2 layers66.5 × 36.5 mmSyncBoard, the printed circuit board in 3D

    SyncBoard

    anthonytec2/OctoSense

    OctoSense is a multimodal dataset

    9 parts211MIT
  • 2 layers312 × 140 mmTsynth2 Rev1.3, the printed circuit board in 3D

    Tsynth2 Rev1.3

    Electrotechnique/TSynth-Teensy4.1

    TSynth for Teensy 4.1

    108 parts182
  • 2 layers316 × 119 mmTeensy Grovebox, the printed circuit board in 3D

    Teensy Grovebox

    jerry20091103/Teensy_Grovebox

    A portable synth and music multi-tool made with Teensy 4.1

    142 parts150MIT
  • 2 layers304.8 × 95.2 mmLMN, the printed circuit board in 3D

    LMN

    FundamentalFrequency/LMN-3-ECAD

    Electrical CAD Files for the LMN-3 Project

    106 parts106CC-BY-SA-4.0
  • 2 layersT41-Main+RF board V012, the printed circuit board in 3D

    T41-Main+RF board V012

    DRWJSCHMIDT/T41

    This is the repository for the officially released V10, V11, and V12 versions of the T41 Software Defined Transceiver hardware and kits.

    255 parts66

Questions

How big is the Tuco PCB?

It measures 144 × 127 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Tuco use?

27 parts, built around the TEENSY 4.1 and S16B-XH-A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Tuco KiCad files?

From the KXR-UCF/mdfc repository on GitHub, at the commit this page was made from: the board is tuco/tuco.kicad_pcb and its schematic _templates/Heisenberg_/Heisenberg_template.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Tuco design in my own project?

Its repository states no licence, so its author keeps all rights: ask KXR-UCF before reusing the design.