

Klxecu
Speeduino based ECM for the fuel injected KLX 250 and 300
- Size
- 80.3 × 86.4 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 79
- Nets
- 121
- Pads
- 325
- Tracks, vias
- 784, 21
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 6 (file 20211014)
- Created
- 21 May 2022
- Updated
- 2 Mar 2022
Overview
Klxecu is an open-source printed circuit board by JourneyMan61, from the JourneyMan61/klxecu repository on GitHub. It is a 4-layer board of 80.3 × 86.4 mm with 79 parts on 121 nets, routed with 784 tracks and 21 vias.
It is built around the TC4424AVPA, TC4422ESM and TC4424EPA, with the SSM3K357R, 1SMB5919BT3G and B130-13-F(MS) among its other parts. Its parts include 21 capacitors, 21 resistors, 8 connectors, 7 transistors and 5 ICs.
Main components
6TC4424AVPA
PDIP-8-40℃~+150℃ 12ns 12ns 2 4.5A 4.5A 4.5V~18V MOSFET PDIP-8 Gate Drivers ROHSMicrochip TechnologyGate DriversTC4422ESM
SOIJ-8-40℃~+150℃ 1 200uA 4.5V~18V 60ns 60ns 9A 9A MOSFET SOIJ-8 Gate Drivers ROHSMicrochip TechnologyGate DriversTC4424EPA
PDIP-823ns 25ns 3A 3A MOSFET PDIP-8 Gate Drivers ROHSMicrochip TechnologyGate Drive ICsSSM3K357R
SOT23FSOT23F New Arrivals ROHSToshibaUncategorised1SMB5919BT3G
SMB(DO-214AA)Zener DiodesFUXINSEMIB130-13-F(MS)
SMASchottky DiodesMSKSEMI
README
README.mdklxecu
Speeduino based ECM for the fuel injected KLX 250 and 300. Firmware compatible with the Speeduino 0.4.4c. It has only one fuel and ignition channel, but adds a few extra features, namely:
- control of the check engine/temperature warning lights on the dashboard
- control of the secondary throttle plate in the intake (we'll abuse the open loop idle control built in to the speeduino)
- control of the bike's safety switches (tbd, might just use some logic gates. currently a DIP8 socket is available on the board for testing)
- auxiliary "self diag" pin connected to the speeduino processor
This project borrows from the following:
- NO2C Speeduino - https://github.com/turboedge/SpeedyBoards for parts of the board design
- Speeduino Hardware - https://github.com/speeduino/Hardware for the VR conditioner and other bits of the board design
- Speeduino Firmware - https://github.com/noisymime/speeduino for the ECM firmware
Parts
79| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C5, C6, C7, C10, C13, C14, C15 |
| 7 | 470 | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R6, R7, R8, R10, R12, R13, R14 |
| 6 | SSM3K357R | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q4, Q5, Q6, Q7 |
| 5 | 0.22uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C8, C9, C11, C12, C18 |
| 3 | 2.49K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R3, R9, R11 |
| 2 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C2, C3 |
| 2 | 0.33uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C16, C17 |
| 2 | 1K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R5, R18 |
| 2 | 1N5818 | Diode_THT:D_DO-41_SOD81_P7.62mm_Horizontal | D3, D4 |
| 2 | Jumper_3_Open | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | JP1, JP3 |
| 2 | MountingHole_2.2mm_M2_Pad | MountingHole:MountingHole_2.2mm_M2_Pad | PAD3, PAD4 |
| 2 | TC4422 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP4, JP5 |
| 1 | 0.1uf | Capacitor_SMD:C_0805_2012Metric | C19 |
| 1 | 100K | Resistor_SMD:R_0805_2012Metric | R16 |
| 1 | 100K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R19 |
| 1 | 100uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C21 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R21 |
| 1 | 10R | Resistor_SMD:R_0805_2012Metric | R20 |
| 1 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-7343-31_Kemet-D | C1 |
| 1 | 1K | Resistor_SMD:R_0805_2012Metric | R17 |
| 1 | 1SMB5919BT3G | Diode_SMD:D_SMB | D2 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R2 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R15 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C20 |
| 1 | 2k | Resistor_SMD:R_0805_2012Metric | R1 |
| 1 | 3.9K | Resistor_SMD:R_0805_2012Metric_Pad1.20x1.40mm_HandSolder | R4 |
| 1 | 47uF | Capacitor_Tantalum_SMD:CP_EIA-3528-21_Kemet-B | C4 |
| 1 | Arduino Mega 2560 Pro | mega_2560:mega_2560_pro | U3 |
| 1 | B130-13-F | Diode_SMD:D_SMA | D1 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | Conn_02x04_Counter_Clockwise | mega_2560:vr_conditioner | J4 |
| 1 | DIP8 | Package_DIP:DIP-8_W7.62mm_Socket | J3 |
| 1 | IGN_ARD_OUT | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J6 |
| 1 | IGN_CONN | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J8 |
| 1 | IGN_DRV_OUT | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J7 |
| 1 | Jumper_2_Open | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP2 |
| 1 | LM2940S-5.0/NOPB | Package_TO_SOT_SMD:TO-263-3_TabPin2 | U2 |
| 1 | Pololu_Breakout_A4988 | Module:Pololu_Breakout-16_15.2x20.3mm | A1 |
| 1 | S36B-WPZK-A | mega_2560:S36B-WPZK-A | U1 |
| 1 | SP721 | Package_DIP:DIP-8_W7.62mm | IC1 |
| 1 | STP62NS04Z | Package_TO_SOT_THT:TO-220-3_Horizontal_TabDown | Q3 |
| 1 | TACH_OUT | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | J5 |
| 1 | TC4424 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | JP6 |
| 1 | TC4424AVPA | Package_DIP:DIP-8_W7.62mm_Socket | U4 |
| 1 | Varistor | Varistor:RV_Disc_D15.5mm_W4.7mm_P7.5mm | RV1 |
| 1 | cam_sensor | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J1 |
The 76 most common of 79 parts.
More from JourneyMan61/klxecu
3Similar boards
- 2 layers100 × 100 mm

- 2 layers100 × 100 mm

- 4 layers100 × 100 mm

- 4 layers100 × 100 mm

- 2 layers98 × 79.5 mm

Flex over can
twisted-builds-llc/sloppy_holley_flex-over-can
CAN bus input/output module for Holley Terminator X (also HP/Dominator class ECUs).
86 parts1 - 2 layers109.4 × 94.4 mm

- 2 layers80 × 99.8 mm

- 4 layers51.1 × 45.1 mm

Rave Controller
D3stan/EV-Controller
ESP32-based exhaust valve controller for 2 stroke motorcycle.
23 parts1
Questions
How big is the Klxecu PCB?
It measures 80.3 × 86.4 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Klxecu use?
79 parts, built around the TC4424AVPA, TC4422ESM, TC4424EPA and SSM3K357R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Klxecu KiCad files?
From the JourneyMan61/klxecu repository on GitHub, at the commit this page was made from: the board is v3/klxecu.kicad_pcb and its schematic v1/klxecu.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Klxecu design in my own project?
Its repository states no licence, so its author keeps all rights: ask JourneyMan61 before reusing the design.

